Ray May 15, 2014 for Model Number ED25DWXTW03 There is no green ground connection, do I just tape it up? Which connector do I attach the black wire to?
1 Answer Ray, The black lead will go on terminal number 2 for your model refrigerator. For the ground wire just attach to a piece of metal on the inside of the refrigerator Read More...
Repair Rookie May 13, 2014 for Model Number Estate by Whirlpool TS25AFXKQ03 Which terminal does the black wire go on for my Estate Model TS25AF? Thanks!
Mike April 17, 2014 for Model Number ED25PQXFW01 I think the black wire should go to terminal #1 on the defrost timer. Can you confirm this? Thanks
1 Answer Hello Mike, You are correct. The black lead connects to terminal number 1. This will provide a defrost cycle every 8 hours. Read More...
Bill April 07, 2014 for Model Number Whirlpool ED25DQ s x s refrigerator Evaporator coils completely freeze over. Cleaned condenser coils and manually defrosted refrigerator. Week later it is frozen over again. Door seals look to be good. Think it is defrost timer, defrost thermostat or heater. How do I determine which one? Thanks
1 Answer Hello Bill. It sounds like you may have a defrost problem with the unit. If so, you will need to test the defrost heater and the defrost thermostat. They should read closed for continuity when cold. You can test this with a multi-meter TJMA-DMT3. I will include a link at the end to assist you how to use the multi-meter if needed. If both parts are good, you will need to replace the defrost timer. Once the problem is repaired, you will need to thaw out the ice on the coils before the unit will operate properly. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Tony March 30, 2014 for Model Number ed5hhgxtq00 Hello, I replaced the thermostat, heating element and timer to repair a no defrost situation. Couldn't find a wiring diagram and now the defrost only works when I manually adjust the timer. What is the correct jumper position for my application? Thanks, Tony
1 Answer Hello Tony. For continuous run timerpush slotted loose timermotor lead over & all theway down terminalnumber 1 with wiretoward timer motor. Read More...
Matt March 29, 2014 for Model Number Kenmore Coldspot 106.57378700 Can you please tell me which pin I should connect the black wire to for my particular model?
1 Answer Matt, For your unit you will need to connect the black lead on the defrost timer to the number 1 terminal of the timer. Read More...
Bob March 26, 2014 for Model Number Model# ED27PQXEW00 My unit will run for about 8 hrs. It will stop and not restart. If I turn the cold control off and then back on it will run again for about 8hrs. Making me believe the cold control is bad. But the unit will also restart if I turn the defrost timer until it clicks. So a little confused wether I need a cold control or a defrost timer. Thanks I'm advance
1 Answer Hello Bob. Based on the information you provided, it sounds more like the cold control than the timer in the unit. The reason is, turning off and on the cold control has no effect on the timer advancing in the unit. You will need to replace the cold control. Read More...
Theresa S. March 25, 2014 New defroster and defrost timer. It works initially, however when after it cools refrigerator and makes ice cubes it turns off and doesn't go on again. To operate, I put it on manually. When we installed the defrost timer we never set it by turning clockwise .Could that be the problem?
1 Answer Theresa, No advancing the defrost timer wouldn't make a difference in the timer operation. You do have to make sure the timer is wired correctly based on the wiring diagram of the refrigerator. The cold control could be the issue as well, but without a model number, we can't verify the proper wiring at the timer, or trace circuits to advise you properly. Read More...
1 Answer Hello Theresa. For continuous run timerpush slotted loose timermotor lead over & all theway down terminalnumber 1 with wiretoward timer motor. Read More...