Jim D October 20, 2012 for Model Number GR9FHKXPBOO Whirlpool Refrigerator The replacement defrost timer has a black wire, and I'm not sure what terminal number to attach it to. Thanks in advance for your help.
1 Answer Jim, Based on your wiring digram, and the W10822278 defrost timer kit instruction sheet, you have a "version 2" Cumulative Compressor Run Application" (page 1, figure 3), and you will use Procedure 3 (page 3, bootom half) to attach the wires to the repalcement timer terminals. The Black timer motor wire will attach to terminal #1 along with the orange wire. Good Luck and Thanks Read More...
Frank October 15, 2012 for Model Number frs26hasb6 frigerdaire side by side has just stop freezing and icemaker stop ! just found out that a soda was left in there and exploded could this had something to why it doesnt work it was manufactured in 7/03
1 Answer Frank, It's not likely that an exploding soda would cause a refrigerator to stop cooling, or an icemaker to stop working. You may want to check and make sure there is not a heavy build up of frost or ice on the back wall of the freezer, and that you can hear or feel the evaporator fan operating. You could be on the right track, your refriigerator has an ADC control 5303918476 and the circuit to the compressor may have failed and the refrigerator would stop cooling. Read More...
Verlina October 15, 2012 for Model Number ED25PEXHW00 I purchased a new defrost timer and like most people am confused as to which terminal the black wire goes on. I have read through all the questions and answers and since I could not find my exact model number I need to verify if the black wire needs to go on Terminal 1 or 2. Would be helpful if you had a chart that cross referenced the model numbers with which terminal the black wire goes one. Would be quicker for both of us. Thanks for your help.
1 Answer Verlina, As the instruction sheet states" Unplug refrigerator or disconnect power. Before installing timer, check wiring diagram or Tech Sheet in product to determine type of timer application." Based on the wiring diagram for your refrigerator, you will wire the new defrost timer according to "Version 2" Cumulative compressor run application (fig 3 on pg.1) and use Procedure 3 (pg.3) to wire and install the new timer. Read More...
Jon October 05, 2012 for Model Number Maytag MTB2156DEW What terminal do I connect the black wire to? Thank you Jon
1 Answer Hello Jon, Connect the Black wire to the terminal labeled number 1. This will allow a defrost cycle every 6 hours of continuous run. Read More...
Gary September 21, 2012 for Model Number ED25PQXFH02 Hi, I purchased a new defrost timer and don't know if I have a continuous run or a cumlative run model refrigerator. Which pin does the black wire go to? Thanks...Gary
1 Answer Hello Gary. Based on the model number you provided, For continuous run timerpush slotted loose timermotor lead over & all theway down terminalnumber 1 with wiretoward timer motor. Read More...
Jim M. September 18, 2012 for Model Number ET18GKXHTO SER EL0715502 What terminal do I connect the black wire to? Thank you! Jim
Paul September 14, 2012 for Model Number EEB191PK Where does the Black Wire go for for the Whirlpool EEB191PK NR3?
1 Answer Hello Paul. Sorry, but you will need to use the wiring diagram on the unit, and the instruction sheet to determine where the wire goes on the timer. The wiring diagram is not available for this model and we can not help without the diagram. Thank you. Read More...
1 Answer Hello Paul. The model number you provided does not work. We will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Nel September 07, 2012 for Model Number ET4WVLXVQ00 I purchased a new defrost timer. What terminal do I connect the black loose wire? My refrigerator is model #ET4WVLXVQ00 Whirlpool. Thanks :D
Dale August 22, 2012 for Model Number Ed26 ssxlwro Would a defective defrost timer make a loud ticking noise?
1 Answer Hello Dale. Yes if the gear is broke, it can cause the timer W10822278 to be very loud and click. Read More...