David N. June 09, 2015 for Model Number LSR8444LQ0 I recently replaced the lid switch, as it had basically fell apart. We were able to get three loads completed successfully afterwards; but on the fourth load the tub would not empty during the last FINAL RINSE of the NORMAL wash mode. I was able to rotate the knob to other RINSE positions in hopes of removing the water, but it only worked when I went to the FINAL RINSE of the DELICATE cycle. Also, while this was happening, the Timer/Load Swith area was "chattering" loudly, or at least more than usual (if it's supposed to chatter at all!) So what do you think? Timer Control Switch?
1 Answer Hello David. Yes, it sounds like the timer is bad and will need to be replaced on the unit. Read More...
Mike June 04, 2013 for Model Number lsr8444lq0 My whirlpool washer after completing its wash cycle stopped working. I tried every cycle no agitate, spin or drain. I drained the water and tried again it would fill with water but thats all.
1 Answer Hello Mike. It sounds like the lid switch is bad and will need to be replaced on the unit. Check and see if it is broke or bad on the unit. Read More...
Jaime November 16, 2012 for Model Number Lsr8444LQ0 Our washer recently stopped in the middle of a cycle, when it was supposed to start it's spin dry phase. I tried everything to test it, setting the timer to different settings/modes to try to gauge what was going on and it absolutely would not spin (and ultimately drain) on any setting. After researching a little online, I decided to start with the lid switch, since it was broken by my g/f trying to get it to work before I got home - figuring it was probably bad, and she just made it worse by completely breaking it. The machine would agitate and rinse, but WOULD NOT drain or spin. I got a new lid switch, installed it and PRESTO, the spin cycle now works, however, it is now the only thing that works. The machine WILL NOT fill with water. Everything is hooked up. I've taken all the power cords out of their respective slots and reseated them. One of two things happen when I try to start a cycle on the machine: more frequently the machine will make a humming noise that is originating from the back of the machine near the top but below the timer. Other times timer will make some clicking noises. This happens when I try to set it to rinse as well. It's always either timer clicking or humming from the back - it doesn't seem ever like both are happening simultaneously. The thing that blows my mind is that everything except the spin was working prior to me changing the lid switch, and now the spin is the only thing that works. Please HELP! I'm trying to DIY because we have limited resources available presently. Thank you!!!
1 Answer Hello Jamie. You need to check and see if she turned the water supply off behind the machine. It sounds like the water is turned off. Read More...
Chris July 28, 2012 for Model Number lsr8444lqo I have a Whirlpool washer that will fill up and agitate but will not drain or spin. I did not check the lid switch with a meter. The timer makes a lot of funky noise. Is the timer most likely bad?
1 Answer Hello Chris, You need to check that lid switch 3949247V. If the lid switch is okay, my next question is do you hear any noise other than the timer? If so, you could have a bad motor coupler 285753A. If not, you could have a bad connection, or a bad pressure switch W10337780. I guess the timer could be an issue, but the most common parts to fail should be checked first. Read More...
Doug L. February 04, 2012 for Model Number LSR8444LQ0 whirlpool washer The washer will fill up and agitate but when it goes to rinse it will not advance and therefore will not spin. I moved it manually to the next cycle,same thing also the 3rd cycle the same. all three will fill with water but will not rinse or spin.
1 Answer Hello Doug. If the unit will wash, but will not spin or drain, you will need to check and see if the lid switch 3949247V is bad on the unit. It should read closed with the lid closed. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Scooter July 07, 2011 for Model Number LSR5100LQ0 HOUSE HIT BY LIGHTNING WASHER STOP WORKING.ANY IDEAS? ALSO TIMER ON MY DRYER STOP WORKING. HELP.
1 Answer Hello Scooter, as for the washer you could have a defective lid switch 3949247V or the timer WP3951166 itself has shorted out. You will want to test the components with a multi meter MA-DM1. If your dryer does nothing, you might have a blown thermal fuse or damaged timer. You can use the multi meter to test all of the dryer's thermostats, they should all read close for continuity. Here is a link you can refer to for help with using a multi meter: http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html . Hope this helps! Read More...
J.D. April 02, 2011 for Model Number LSR8444LQ0 Is the timer the only possible problem when the washer just goes dead at the drain portion of every wash cycle? The agitator works. I can hear the motor running during wash. the fill portion of the cycle works. But there is no sound at all when the timer hits the drain section of the cycle. Everything just stops. The timer does not buzz or sound like it is trying to go on. it is just dead.
1 Answer Hello J.D! If the unit is not spinning or draining I would start with checking your lid switch. This will stop the unit from spinning and draining. You should hear a clicking noise when you close the lid, this activates the switch. If the part is bad order 3949247V. Thanks! Read More...