Gary February 22, 2025 for Model Number KUIC18PNTS4 Does the display transformer provide voltage to the control board as well as the various components in the ice machine. Should the secondary voltage be DC or AC. I'm assuming DC but want to be sure.
1 Answer Hello Gary, thank you for contacting Appliance Parts Pros.[WP2310139] is not a display transformer, it supplies low AC voltage to several other components like the recirculation pump and reservoir drain pump. It should have 120v AC incoming on the Black and White wires, w/ 8-9v AC from Yellow w/ Blue tracer to Yellow and 11-13v AC from Red w/ Black tracer to Gray on the outgoing side. Read More...
John January 24, 2023 for Model Number KUIC15PRTS1 Transformer seems to get unusually hot even when ice maker is turned off but plugged in. There is also a slight hum when off. Does this point to a problem with the transformer or is it normal? I feel like its so hot it is melting ice when it is making it or that it will damage another component. Thank you
1 Answer John,The transformer does have power to it any time the machine is plugged in so it could be a little warm to the touch. Read More...
Johnny January 12, 2017 for Model Number KUIS15NRTB2 My ice machine quit making ice. I changed the pump and the water level sensor. Its now making very little ice. the ice is building up on the plate but looks like its not filling up the cutter grid. It seems the cutter grid wires are not as hot as should be. I don't see any broken wire, but there seems to be a little corrosion. How do you think I should proceed. Thanks
1 Answer Johnny, The cutter grid is very low wattage and should not be really hot. You should be able to touch the cutter grid and hold your hand on it. The ice should drop down onto the cutter grid after it forms on the plate. If it is not then you will want to check the thermistor on the bottom of the ice plate to make sure that the thermistor is good. Read More...
Klane October 03, 2015 for Model Number KUIS18NNXS0 I just replaced on e of the grid wires and ice maker worker great for a couple hours, then all the power just went off? Light in bin and non of the controls work. I have electricity to machine. Do you have any ideas?? Thanks
1 Answer Klane, You will want to test the transformer on your unit to make sure that it is good. If the transformer checks ok then the issue will be the control board. Read More...
Dkg September 17, 2015 for Model Number KUIC15PRTS2 Ordered control board from you. The repairman said it was out. Still no power to controls. Would the transformer have anything to do with this, It was very warm to the touch Thanks
1 Answer DKG, Yes the transformer can cause the controls on the unit to not work. You can test for 120 vac going in to the transformer and then test for 12-24 vdc coming out of transformer to make sure that it is working. If there is power in but not out then replace the transformer. IF there is no power in the check back from the transformer back to the power supply cord to ensure good wiring. Read More...
Bill August 24, 2015 for Model Number 106.89589705 Good morning, the ice maker pumps, sump and recirulate not working. Voltage at the plug in is 0.50 is this enough for pumps to run? Thanks
1 Answer Hello Bill. No, that is not enough for the unit to run. You need to check wiring on the unit and the control if the wiring is good. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Paul November 01, 2013 for Model Number mim1554wrs2 Ice cutter grid seems to cut slowly. Showing 8 volts at plug is that normal or should it be more.
1 Answer Paul, 8 to 8.4 volts DC is the correct voltage range for the cutter grid circuit from the control board. The cutter grid assembly should have a resistance reading of 4(four) to 5(five) ohms resistance if it is intact, It sounds like it is operating properly at this point.Perhaps someone has adjusted the cube size to a thicker setting ? Read More...
Jeff December 09, 2012 for Model Number KUIS18NNTS1 I amd getting a 22 volt reading at the plug in terminals for both pumps. Since pumps are rated at 12VAC is the 22 volts normal?
1 Answer Hello Jeff, If you are getting 22 vdc then your transformer [AP3956373 is defective and would need to be replaced. You should have no more than 13.2 vdc coming to the pumps. Read More...