Mike July 23, 2018 for Model Number WED6400SW1 When you try to start the dryer it starts like it is in wrinkle free mode? What would cause that to happen and not allow it to run its cycle
1 Answer Hello Mike, if your unit is not recognizing when you try to use any of the other functions it could be the user interface WP8563974. Check the push in buttons on the control to make sure they are not damaged. Hope this helps! Read More...
Tyler March 15, 2018 for Model Number WED6400SW0 My dryer has no power to the controls. I have power at the outlet and power to the back of the dryer. The control panel is completely dead tho. Control board? And which one? Looks like there is 2 of them. Thanks
1 Answer Tyler, You will want to check the thermal fuse on the blower housing to make sure that it is not blow but if it is not then this will be a control board issue and will need part number WPW10111616. Read More...
Steve February 01, 2017 for Model Number WED6600VW0 My button was broken on my dryer and I took out the circuit board but I can not get the plastic grey piece out that holds the button etc. Can you please help me. It has 3 tabs in the front and back, and one each on the sides. I have pushed ,pulled etc. and it want budge.
1 Answer Steve, If the plastic piece for the start button is broken then this would require the control board on the unit to be replaced. The gray plastic piece is not available separately. Read More...
Patrick June 02, 2014 for Model Number WGD6400SWO Start button stopped working on my 7 yr old Whirlpool Cabrio gas dryer, do I need to replace the electronic interface board - 8563974? Can I still get new parts or only remanufactured?
1 Answer Hello Patrick. If you are sure the start button is bad, you will need to replace the electronic control WP8563974. Read More...
Amy March 18, 2014 for Model Number WED6400SGO Whirlpool Cabrio Dryer Part #8563974 is super glued to the inside of the plastic cover. How can you replace the control without breaking the plastic cover? The dryer start button doesn't work.
1 Answer Hello Amy, This part WP8563974 should only be clipped onto the control panel and there may be a couple of screws. If it has been glued, the control panel will most likely have to be replaced to correct the issue. Read More...
Marc February 03, 2014 for Model Number WED6400SW1 Whirlpool Cabrio dryer, about 6 years old, stopped working. Control panel lights up and I get a flashing F1 error code. Any idea what the cause?
1 Answer Hello Marc! F-01 flashes when there is a primary control failure. Replace the machine control electronics. The part number is WPW10111616. Thanks. Read More...
Kd January 09, 2014 for Model Number wgd6400ws0 The start button does not engage to turn machine on. Do I need to purchase a new console for 200 and how difficult is it to replace? Thank you KD
1 Answer Hello KD. Yes if the start button is not working, you will need to order and replace part number WPW10110325. Read More...
Michael January 01, 2014 for Model Number WDG6400SG0 Can I order just the gray plastic housing inside the console. Because a plastic tab broke on the Start Button. What is the part # if you have it? Thank You.
1 Answer Hello Michael! Unfortunately, parts to the electronic control WP8563974 are not available separately. Sorry about that! Read More...
David December 09, 2013 for Model Number WED6400SW0 I was able to get the circuit board out, but I can't get out the gray plastic piece the broke in the control panel to replace it... How does that piece come out?
1 Answer Hello David. Once inside the control panel there is locking tabs you release to pull the board out of the control panel. Read More...
Patrick July 18, 2013 for Model Number Whirlpool Cabrio Dryer WSG6400SW0 I just purchased a new user control interface and when I installed in the unit all the indicators turned on. I can't even get into diagnostic mode. Any suggestions?
1 Answer Hello Patrick. It sounds like the unit has a stuck button. You need to check all the wiring and buttons on the control panel. Read More...