John August 18, 2014 for Model Number LSE7806ACE There are two questions answered with regards to this part that have the same issue I had with mine. They both would not fill, but would spin. One answer says to replace the pressure switch, the other says to replace the lid switch. My machine now blows the 1 amp fuse in the block inside the front panel of the washing machine, and does not function at all. What do you suggest?
Bill April 15, 2014 for Model Number maytag lsg7806aae Washer fills but will not start agitation. Is it the water fill switch?
1 Answer Hello Bill. You need to check and see if the lid switch is bad and needs to be replaced on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Adam March 28, 2014 for Model Number LSE7800 Maytag Washer My washer will fill with the water then it wont switch to the agitation cycle. Please help.
John B July 15, 2013 for Model Number LSE7806ACE Washer will fill on it's own when not in use-it will overflow.
1 Answer John, This issue would be caused by a faulty water valve since it is continuing to allow water in even when off. Read More...
Gary March 17, 2013 for Model Number LSE7806ACE I have a maytag model #LSE7806ACE. At load size med it works good the drain valve stays closed. At load size large it keeps filling but the drain valve is open so it does not advance the wash cycle. The air tube is not blocked and where it connects to the tub is not clogged. I think the water level switch is faulty. What do you think?
1 Answer Hello Gary, Based on the information you provided, it sounds like the pressure switch is bad and will need to be replaced on the unit. Read More...
Larry March 06, 2013 for Model Number LSE7804ACE My washer does not fill with water but will spin. I don't know what it could be. Can you help? Thanks,
1 Answer Hello Larry. You will need to order and replace the lid switch on the unit. Also, order and replace the fuse WP22001555 on the unit. Read More...
Michael K December 19, 2012 for Model Number Maytag Washer Dryer Stacked LSG7806AAE Washer will not stop filling. Replaced water level switch. (Still same problem). Air Tube seem clear. Even when I blow into the air tube it will not stop filling. (When lid is open it does stop filling so this should ruled out water valves) When on small load size it will start to agitate with water level switch connected or not but will not stop filling. On medium or large loads it will just keep filling but will never start to agitate. Any suggestions. Thanks
1 Answer Hello Michael. Based on the information you provided, you need to check the pressure hose for cracks and make sure the air dome on the side of the tub is not clogged. If everything is good, then there is a wiring issue with the unit. Read More...
Joe October 13, 2012 for Model Number LSG7804AAE Tub filled Large load & just started to agitate & stopped. I suspected door switch. I emptied clothes & water from tub & pulled washer from dryer frame & tub started to fill again. I shut it off & emptied it again & tried to fill it to lowest level but it continued to fill higher. Tried shutting off water supply to & turn on machine but it still won't spin. Could it only be the level switch?
1 Answer Joe, It does sound like a water level switch or air dome hose issue 12002304 and 22001616 These two components control the water level in the tub. It doesn't sound like a faulty fill valve, at this point. The next check is at the umbilical cord, Make sure all the pins and receptacles in both ends are clean, make good, proper contact, and the ends are locked and secure when plugged into each other. If alls OK and the washer still won't spin and drain, then check the lid switch assembly 12001513 or 12001514 (depending on series or serial number). Read More...
Joll September 24, 2012 for Model Number LSG7806AAE Water starts to fill and the same time machine starts to turn. Then the water doesnt stop to fill until it overflows.
1 Answer Hello Joll. If you can stop the water with the power, replace the water level switch. if you have to turn off the water, replace the valve on the unit. Read More...
Gary April 27, 2012 for Model Number LSE7806ACE Water will come into the tub at desired levels but it will not advance to the next cycle.
1 Answer Hello Gary, If the water level switch 12002304 is passing voltage, check the lid switch WP22001682. If it tests good I would suspect the contacts in the timer WP22001924 not passing voltage or the timer motor has failed. Read More...