Jeff May 28, 2022 for Model Number C301 When reinstalling fan on blower motor, how do you realign the fan onto the shaft? Also, a metal clip fell off the fan, where does it belong on the fan?
1 Answer Jeff, the set screw on the fan base would need to be aligned with the flat spot of the motor shaft. In regards to a metal clip, this could have come from where a wire goes into the housing or from the plenum housing. Read More...
Suzy March 21, 2020 for Model Number C316 I can't figure out how to get the blower wheel off. It is covered in thick grease and really needs be cleaned.
1 Answer Suzy, On the side of the blower wheel, there is a set screw that you would loosen and then you will have to pull the blower wheel off. If the blower wheel is stuck you may need to tap the motor shaft to get it to come free. Read More...
Bill January 06, 2016 for Model Number Jenn Air D140 Paper towel got sucked down the exhaust and is making terrible noise. How do I get to the paper towel to remove it?
1 Answer Hello Bill. You will need to remove the vent hose from the blower wheel to access and remove the paper towel. Read More...
Jim C. April 05, 2014 for Model Number 88353 jennair When the blower motor comes on, there is a lot of vibration. it shakes the frying pan and make a lot of noise. Do you know which parts need to replace to reduce vibration?
1 Answer Jim, You will need to remove the blower motor 707704K and blower wheel WPY707985 from the plenum assembly, and check to see if something got dropped into the plenum, and got sucked into the blower wheel. Check and make sure the motor mount clamp inside the motor cover, is not loose or worn and allowing the motor to vibrate and shake. Read More...
Doug1966 January 02, 2014 for Model Number C228 The blower wheel no longer spins (but tries to) likely due to grease and deposit buildup, but you can still hear the motor activation. Is it sufficient to replace the Blower wheel, and what else might I need to include?
1 Answer Hello Doug1966, This is more likely to be a bad winding in the motor 707704K. I doubt that just changing the blower wheel will solve the issue. Read More...
John August 15, 2012 for Model Number AP4292620 Is this like a filter and does it need to be changed . Mine looks like grease on it . I have mine out of the counter top and would like to just change all filters and any other parts it needs . The Jar lid only which holds the grease needs to be replaced Thank You John 415-892-7733
1 Answer Hello John. No, WPY707985 is the blower wheel that moves the air. WP707929 is the grease filter for the unit. Read More...
Dennis April 04, 2012 for Model Number jed8230ads Can the bearings be lubricated or replaced on the motor or do I need to replace the motor? It currently overheats and quits.
1 Answer Hello Dennis, No sir, I'm sorry to say that the bearings are not replaceable on these motors. They can't be lubricated as they are sealed bearings. If it overheats, I would definitely check the ducting to insure there isn't a squirrels nest or anything blocking the duct. This may sound ridiculous but I have removed at least 5 bird or squirrel nests in the past three years. Read More...
Dennis April 04, 2012 for Model Number jed8230ads What is the size of the Blower Wheel lock nut and does it require a special tool?
1 Answer Dennis, The "set screw" or "Lock nut" that holds the blower wheel to the motor shaft is a "hex head" and will require a set of "allen wrenches" or "hex key" wrenchesto remove and install the wheel. I could be wrong, but it appears the set screw would require a 3/16 or 1/4 inch wrech to loosen and remove the set screw. Thanks and Good Luck Read More...
1 Answer Hello Ken. No, you can unscrew the set screw on the blower wheel WPY707985 and slide it off the motor shaft. Hope this helps. Read More...