Parts for Columbia 12AJ836L597 / 2008: .Quick Reference Parts

This is a simple set of lawnmower ignition keys. They’re also used for an array of riding mowers, lawn tractors, and even snowblowers. To simplify repair and replacement procedures, most manufacturers use standardized keys for all their machines in a given class. As a result, a single key can be used for dozens of machines. The keys are manufactured from stainless steel, with an INDAK logo stamped into the center. Regardless of whether the machine is a walk-behind mower or a full-sized lawn tractor, a keyed ignition is easier to operate than a recoil cord. Similarly, replacing a key is generally straightforward. The exception is if the old key has snapped off in the ignition. In this case, a set of needle-nosed pliers can sometimes be used to extract the key. A powerful magnet can also be helpful if the broken key is being stubborn. In the worst-case scenario, the ignition may need to be replaced. This is an OEM part sourced directly from MTD, and it is sold as a set of two.

This replacement part is a V-belt. This is a genuine replacement part made by MTD. V-belts are usually found in engines and allow for the parts to run smoothly and efficiently while in use.A new v-belt might be needed if the current one is becoming worn down or is damaged. This can be caused by normal wear and tear over time as belts typically experience lots of friction during use. Be sure the engine is completely turned off and cooled down before attempting to replace any kind of belt. Refer to the owner manual for more specific directions on how to replace this part.This v-belt is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

This is a spark plug that is installed on a variety of different outdoor power equipment. A spark plug is a component that delivers the electric current from the ignition system to the internal combustion engine. One spark plug is included in this package. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment.The spark plugs can get dirty, and then they will require a replacement. Never perform care and maintenance on an appliance that is powered on.This spark plug is a genuine OEM MTD part. It is sold individually. This specific spark plug is compatible with snowblowers, lawnmowers, lawn tractors, log splitters, and blowers that are manufactured by MTD, Yard Machines, Troy-Bilt, Bolens, Yard-Man, and Cub Cadet.

The blade support is found between the blade and the bolt. As its name suggests, it is designed to provide support for the blade to ensure it is secured to the base of the mower deck. It is made of metal and it will need a replacement if it becomes worn or damaged. To replace a blade support or blade spacer, first, the engine needs to be cool. Remove the wire and boot from the spark plug. Tip the mower back on its handle assembly and use a piece of wood or sturdy object to hold the cutting blade in place. Remove the old blade support and blade. When installing the new one, ensure that the blade's sharp edge faces away from the mower deck. Re-thread and torque the bolt between 40 and 50 ft-lbs. This is an original OEM replacement part for lawnmower blade support made by Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, MasterCut. It is sold individually.

This is a blade adapter that is intended for use with lawnmowers. The blade adapter attaches the motor shaft to the lawnmower blade. A new blade adapter may be needed if there is any damage to the part. Any damage to the blade adapter can make the lawnmower vibrate excessively and loosen the blade mounting. If the blade loosens, it can strike the housing or the ground and cause it to break. This can be dangerous. Blade adapters are designed to be a breaking point between the blade and the crankshaft, making any damages less expensive to repair. Make sure to wear gloves when performing care and maintenance or replacing any parts on a lawnmower. The spark plug wire should be disconnected before attempting to install the blade adapter. A power drill, wrench set, and socket set are required to replace this part.This blade adapter is a genuine OEM Craftsman part. It is sold individually. This particular blade adapter is compatible with lawnmowers that are manufactured by the Husqvarna brand.

This replacement part is a hex bolt. It is a genuine replacement part made by MTD. Hex bolts are named because they are shaped like a hexagon and are different from the regular circle-shaped bolts. These parts are able to hold other parts secure and in place so that everything can operate as needed. A new hex bolt might be needed if the current ones are damaged in any way. It is possible that these bolts become stripped or lodged in place over time due to normal wear and tear and should be replaced. The repair should be fairly easy, only requiring a screwdriver or pliers if the previous part is stuck. Be sure the engine is completely powered down before beginning this repair. This bolt is sold individually. Be sure to purchase the correct amount as many appliances require more than one. This is a genuine OEM replacement part sourced directly from the manufacturer.

A mulching blade has a unique curved or angled design that allows discharging, bagging, and mulching. If its edges are already dull, it can lead to longer mowing time and frayed and torn grass blades. Mulching blade installation is easy. First, unplug the spark plug wire. Then, position the lawnmower on its side. Get a woodblock, preferably 6 x 2 in size, and put it between the old blade and housing deck. Make sure that the wood will prevent the old blade from moving. Take a socket wrench and remove the blade’s nut and washer. Remove the old blade and put the new mulching blade in. Put the nut and washer back and tighten until it is secured. You can use the woodblock to prevent the replacement blade from moving when it is tightened. This mulching blade replacement s an original MTD product. This OEM mulching blade can be used for MTD, Craftsman, Cub Cadet, Murray, Yard-Man, and Bolens lawnmower models. This brand-new mulching blade is sold individually. The support blade and screw hex are sold separately.