Parts for Craftsman 31BH95SI799 / 2012: .Quick Reference Parts

This replacement part is a cable assembly. This is a genuine replacement part made by MTD. This cable assembly is made up of many different wires and is responsible for connecting certain parts together so that they may work in tandem during use. A new cable assembly might be needed if the current one is unable to stay secure within the machine or is damaged in any way. The cables might have become stripped down over time and should be replaced if this happens. This is common after years of normal wear and tear for this to be the case. Be sure the engine is completely turned off and cooled down before attempting to repair this specific part. Refer to the correct user manual before starting this repair. This part is sold individually and is sourced directly from the manufacturer to ensure proper fit. This part is a genuine OEM replacement part.

This light bulb is designed for use with outdoor lawn and garden power equipment such as lawn mowers, snow blowers, and snow throwers. It is compatible with products made by Craftsman, MTD, Columbia, Husky, Yard-Man, Cub Cadet, White Outdoor, and Troy-Bilt.This light bulb attaches to the light socket in a mower or blower and illuminates the area in front of the machine. The purpose of the light bulb is to make the machine operable even when light is sparse. For example, if someone is mowing their lawn at dusk and it gets too dark to see the yard, they'll need a functioning light bulb to finish the job. This is also an important piece for snow blowers because even if it isn't nighttime, a dense snowfall can greatly limit visibility. A light bulb on the front of the machine can make the task less overwhelming when the environment is dark or if visibility is otherwise limited. To replace a broken bulb, unscrew the bad bulb and screw the new one in. No extensive technical knowledge of the machine is required for a simple light bulb replacement.This light bulb is a genuine OEM part sourced directly from the manufacturer, and it is sold individually. It is manufactured by MTD.

This power cord extension is a genuine MTD part, sold individually. This power cord extension can be used as a replacement part for a snowblower. This power cord extension lengthens the reach of the power cord so that the appliance can be used from a greater distance from its direct power source while it is plugged in. The power cord extension might have to be replaced at some point if the cord suffers damage that renders it beyond functionality. This could occur if the cord is frayed, if it gets wet, or if it is punctured, torn, scratched, or eroded to the point that it does not power on the snowblower when properly plugged in. Remember to wear work gloves as a safety precaution while repairing or replacing parts within an outdoor appliance. This is an OEM part sourced directly from the manufacturer. It is sold individually. This power cord extension is compatible with the following outdoor appliance brands: MTD, Toro, Cub Cadet, Ryobi, Tecumseh, Lawn Boy, Huskee, Montgomery Wards, Bolens, Yard Man, Troy-Bilt, and Yard Machines.

Note: This is a quantity of 1 shear pin only. For kit of 4 shear pins with retainers, order OEM-738-04155

This auger cable is a genuine MTD part. It is manufactured for use with snowblowers and snow throwers. On a snowblower, the auger cable connects the control lever and the engagement lever as part of the machine's auger drive system. If the auger cable becomes worn or broken, the snowblower will malfunction and may not work at all.Typically, the auger cable will last the life of the mower, but it may become damaged, especially while performing another repair or through extended use. To replace the auger cable, disconnect the spark plug, let the engine cool, and empty the fuel tank. Remove the belt cover, disconnect the cable from the cable guide pulley, release the cable from the bracket, disconnect the cable completely, and then install the new auger cable.This auger cable is a genuine OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with equipment made by Columbia, Craftsman, White Outdoor, Troy-Bilt, and Yard-Man.

This is a small engine spark plug positioned in the engine cylinder head. It supplies the spark that will ignite the air-fuel mixture to enable an engine to produce power. This particular spark plug is designed with superior corrosion resistance and dependable performance. Small but mighty, this component allows for increased conductivity and heat control. If the spark plug is damaged or in poor condition, many problems may arise in equipment, including sudden stop while running, overheating, and excessive gas consumption. Replace the spark plug by disconnecting the spark plug wire first, then use a socket driver or wrench to remove the spark plug. Install the new spark plug by turning it by hand initially to avoid cross-threading. If it doesn't twist anymore, use a deep socket wrench or socket driver to tighten the plug until snug. The spark plug can also be used to tune up outdoor power equipment or improve a small engine. This part is recommended to be replaced once per season. This part works with lawn mowers, snowblowers, tillers, leaf blowers, log splitters, wood chippers, and others with small engines. It is compatible with brands such as Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, and MasterCut. This is a genuine OEM part directly from the manufacturer and is sold individually.

This is a genuine replacement ignition key that is manufactured by MTD for use in select models of outdoor power equipment. The ignition key is a plastic piece that is inserted into the ignition cylinder to start the machine. Turning the plastic key will signal to the engine to fire. This is a durable plastic piece, but it can become damaged or lost over time, which will render the machine unable to start. Replacing it will be necessary in order to operate the unit. This genuine OEM ignition key is manufactured to exact standards. It can be used in snowblowers and snow throwers from MTD, Yard Machines, Troy-Bilt, Cub Cadet, Yard-Man, and Husky. The durable plastic key is sold as an individual unit and does not require any tools for installation. This is a simple replacement that should only take a couple of minutes. In the event that the old key is damaged or stuck in the ignition, it may take more effort. It is important to disconnect the power supply for safety before performing any repairs, as well as to wear gloves for hand protection.

A cotter pin, also known as a hitch pin, is used to secure pins and shafts in place. Meant for snowblowers, riding lawnmowers, and lawn tractors, this bow-tie shaped cotter pin has a double-end design making it easy to pull or push through either side of a pre-drilled hole. This pin snaps into a locked position without tension, keeping it secure during operation. Designed for lawn and garden maintenance equipment, this part ensures secure fastening. If the power equipment is used frequently, cotter pins may have to be replaced regularly so it would be practical to keep extra bow tie cotter pins on hand. It is highly recommended that work gloves be worn during the installation of this part. This part is compatible with Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, and MasterCut brands of lawn mower, snowblower, and log splitters. This is a genuine OEM replacement part that is sold individually.