Parts for Ge ZV850SB2SS: 01 - Range Hood Parts

The Grease Filter is an OEM part for GE range hoods. It is responsible for trapping grease and other particles from the air as it is drawn through the hood, helping to keep the kitchen environment clean and free of contaminants.  The filter measures approximately 9" x 16".

Causes of a bad grease filter can include clogging due to accumulated grease and debris, damage from cleaning or mishandling, and general wear over time that reduces its effectiveness. 

Symptoms of a bad grease filter include:

• Reduced airflow through the range hood
• Unpleasant odors lingering in the kitchen
• Grease buildup on kitchen surfaces
• Visible dirt and debris on the filter

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is the interior/cooktop lamp bulb used in select GE microwaves. It restores proper lighting inside the cavity and/or over the cooktop so you can clearly see food while cooking and during cleanup.

• Provides illumination inside the microwave and/or for the cooktop task light
• A failed bulb can cause dim, flickering, or no light
• Helps you verify doneness and monitor cooking progress safely

• Unplug the microwave or disconnect power before service
• Allow the bulb and surrounding area to cool before handling
• Use clean, dry hands or gloves to avoid contaminating the bulb
• Replace access covers and secure fasteners before restoring power

This blower and motor assembly moves air through the appliance to support proper ventilation and heating. Replacing a worn assembly restores airflow and can reduce noise or overheating caused by a failing blower. What it does:

• Spins the blower wheel to circulate air through the appliance's airflow path
• Restores normal ventilation and heat distribution when the blower stops working
• Reduces rattling, grinding, or whistling noises from a worn motor or fan
• Helps prevent overheating or poor performance caused by restricted or non-moving airflow

• One blower and motor assembly as shown

• Disconnect all power before beginning service to avoid shock or injury
• Handle the assembly carefully to avoid bending the blower wheel or damaging wiring
• Basic hand tools typically required; follow appliance service manual for disassembly steps

This plastic screw visor is the small trim screw cover that protects and hides the fastener on appliance control panels and exterior trim. It keeps the appearance tidy and prevents dirt from collecting around exposed screw heads. What it does:

• Covers and conceals a panel or trim screw to restore original appearance
• Protects the screw head from dirt, moisture and accidental contact
• Helps maintain a finished look on control panels, bezels and exterior trim
• Commonly used where small plastic caps are needed to match factory styling

• Simple push-on or snap-fit installation; press into place over the screw head
• Use standard hand tools to access screw; disconnect power to the appliance before servicing
• Replace any damaged surrounding trim clips or screws for secure fit

A replacement glass visor that restores the finished front trim and protective cover on compatible GE appliances. Replaces a cracked or damaged front visor to improve appearance and protect underlying components. What it does

• Covers and protects the appliance's front/control trim area from spills, grease and impact damage
• Restores the appliance's finished look when the original visor is cracked, chipped or cosmetically worn
• Keeps underlying controls and components shielded from debris that can affect operation
• Fits as a direct-fit cosmetic/trim piece when the matching part number is required

• One glass visor

• Turn off and unplug the appliance or disconnect power at the breaker before starting
• Handle with care—wear gloves and eye protection; glass edges can be sharp
• Use only the matching OEM part number for correct fit and to avoid damage

This charcoal filter set restores odor removal for ductless range hoods. In recirculating mode, the carbon media adsorbs cooking smells and smoke so your kitchen air stays fresher and the hood performs as intended.

• Traps odors and smoke during recirculating operation
• Helps maintain airflow and ventilation performance
• Replace when saturated or damaged to keep odor removal effective
• Common signs it's time: lingering cooking odors, reduced smoke capture, heavily discolored filter media

• Disconnect power and allow the hood and lamps to cool before service
• Remove grease filters to access the charcoal filters; release clips/tabs, swap in the new set
• Seat filters securely; align any arrows or tabs as marked
• Charcoal filters are not washable—replace when saturated

Replace a cracked or heat-damaged light socket base with this ceramic insulation base. It insulates and secures the lamp receptacle, helping the bulb seat correctly and maintain a reliable connection for consistent lighting.

• Provides a heat-resistant, insulated mounting point for the light socket
• Helps maintain a stable electrical connection to the bulb
• Common symptoms: light won't turn on with a known-good bulb, flickers, bulb won't seat securely, scorch marks or cracking at the socket base
• Restores reliable illumination when the original base is worn or damaged

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the area to cool completely before working near the lamp
• Handle ceramic components carefully; transfer any leads or hardware one at a time to maintain correct wiring
• Use the correct bulb type and wattage as specified by the appliance rating label

The Transformer is an OEM replacement part for GE range hoods. It is an electrical component responsible for regulating voltage levels both internally and to exterior control panels. Proper voltage regulation from the transformer ensures accurate function of hood features like lighting, fan speeds, and exhaust capabilities. 

Causes of a bad transformer typically involve degradation over extended use. Faulty wiring or damage from power surges are other potential causes.

Symptoms of a bad transformer include:

• Lights flickering or not turning on as intended
• Variable or inadequate fan performance  
• Control issues such as buttons not working reliably  
• Abnormal noises from electrical components

This genuine OEM GE part is compatible with GE Monogram and select Kenmore hood brands.

This ring nut is a small threaded retaining nut that secures a mating component to its shaft or connection, restoring a stable mechanical or sealed connection and reducing movement or leaks when properly installed. What it does:

• Holds a shaft, tube or fitting in place by threading onto the mating component
• Prevents components from working loose and reduces rattling or vibration
• Helps maintain a sealed connection where used on fittings or hose connections
• Useful when a stripped or missing nut causes loose hardware or intermittent operation

• One ring nut

• Disconnect power and shut off water before beginning work
• Inspect mating threads and replace if damaged; clean threads before installing
• Hand-start threads to avoid cross-threading, then tighten with appropriate tool; avoid overtightening

Solid-state triac that switches AC power under command of the appliance's electronic control board. Replacing a failed triac restores proper power control to heating elements or motors and resolves intermittent or no-power symptoms. What it does:

• Acts as a solid-state switch on the control board to regulate AC power to heating elements or motors
• Enables the electronic control to modulate output for temperature or speed control
• Failure can cause no heat, intermittent heating, or loss of motor control
• Designed to match the original control circuit; check board mounting and connections before replacing

• Always disconnect all power at the breaker or unplug the appliance before servicing — risk of electric shock
• This part mounts to the control board; handle the board and connectors carefully to avoid damage
• Use anti-static precautions when handling electronic components;
• Verify the part number on the original board before installation