Parts for Electrolux RH42PC60GSB: 03 - Recommended Spare Parts

This electronic power board supplies and regulates voltage to the appliance's control system, helping restore reliable startup and control functions. Replace a damaged board to address intermittent power, no display, or failure to start. What it does

• Regulates and distributes power to the appliance's control modules and user interface.
• Helps restore normal startup when the unit won't power on or shows a blank display.
• Can stop erratic cycling or intermittent operation caused by failed power regulation.
• Works with the control electronics to enable responsive button/display behavior.

• One electronic power board (control PCB)

• Disconnect power at the breaker or unplug the appliance before servicing.
• Handle the board by the edges and avoid static discharge; use antistatic precautions if available.
• Verify harness connections match and seating is secure before reassembly.

This blower assembly circulates air through the appliance to support proper airflow and heat distribution, restoring normal operation and efficiency when the original blower is damaged or failing. It replaces worn or broken blower components to reduce noise and improve performance. What it does:

• Spins the blower wheel to move air through the unit for proper heating, cooling, or venting
• Restores airflow when reduced air movement causes longer cycles or poor performance
• Reduces unusual noise from a wobbling or damaged blower wheel/housing
• Helps prevent overheating caused by restricted or ineffective air circulation

• Disconnect power (and gas if applicable) before starting any repair
• Access typically requires removing exterior panels or the front panel; use basic hand tools
• Inspect and clean surrounding airflow paths and vents of lint or debris while replacing the blower

This metal mounting angle brackets a component to the appliance frame, restoring proper alignment and stable support for the attached assembly. It's a simple replacement that helps stop shifting, rubbing, or loose fits. What it does:

• Provides a secure mounting point for an appliance sub-assembly to the cabinet or frame
• Restores correct alignment to doors, panels, or internal components that rely on the bracket
• Stops movement, rattling, or rubbing caused by a bent or broken angle bracket
• Durable metal construction designed for OEM fit and function

• One angle as shown

• High-level replacement: remove any obstructing trim or components, unfasten the old bracket, and secure the new bracket with the original screws
• Verify alignment before fully tightening fasteners; adjust as needed for correct fit
• Use appropriate hand tools; avoid overtightening fasteners which can strip mounting holes
• Disconnect power when working near electrical components

This control panel is the front console that holds the oven/range controls and user interface, restoring a clean, functional control surface and allowing proper operation of the cooktop/oven controls. What it does

• Houses the control buttons, knobs, and display for the range/oven
• Provides the mounting surface and openings for switches, touchpads, and indicator lights
• Replaces a cracked, scratched, or cosmetically damaged console to restore appearance
• Can resolve issues where buttons or controls are loose, missing, or no longer responding due to physical damage

• Disconnect power (unplug or turn off house circuit breaker) before starting any repair
• Access usually requires removing backguard/console screws and unplugging electrical connectors
• Handle carefully to avoid scratching the finish or damaging clips and mounting tabs

A replacement refrigerator water filter that helps reduce taste and odor issues and improves clarity of drinking water. Fits inline into the refrigerator's water/ice system to restore cleaner-tasting water. What it does:

• Filters impurities that can cause off taste or odor in dispenser water and ice
• Helps reduce visible particles and cloudiness in dispensed water
• Supports proper water flow for the dispenser and ice maker when functioning correctly
• Commonly replaced when water tastes bad, smells, or appears cloudy

• Replace with manufacturer-recommended filter and follow refrigerator-specific instructions
• Turn off the water supply and dispense water briefly to depressurize before removing the old filter
• After installation, flush several gallons of water per manufacturer guidance to clear air and loose carbon
• Dispose of the used filter according to local regulations; check for any refrigerator-specific priming steps

This Lamp Assembly is an OEM part for Frigidaire range hoods. It is a crucial component designed to provide adequate lighting over the cooking area, enhancing visibility and safety while cooking. 

Over time, the lamp assembly can be affected by factors such as frequent usage, heat exposure, or accidental damage. A malfunctioning lamp assembly can lead to poor lighting conditions, which can affect cooking precision and safety.

Symptoms of a faulty lamp assembly  include:

• Dim or flickering lights.
• The light not turning on despite bulb replacement.
• Visible damage to the lamp housing or connections.
• Inconsistent lighting, affecting visibility on the cooktop.
• The lamp assembly overheating during use.

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
 

This refrigerator water filter cartridge replaces a factory filter to help restore clearer, better-tasting water and ice. It's a direct-replacement cartridge designed for simple swap-out maintenance. What it does

• Filters tap water that serves the fridge dispenser and ice maker to improve taste and reduce sediment and chlorine-related odors.
• Helps prevent sediment and debris from reaching dispenser and ice components.
• Common signs you need this part: reduced water flow, noticeable change in water or ice taste, or filter-change indicator.

• One refrigerator water filter cartridge.

• Turn off the water supply and relieve dispenser pressure before removing the old filter.
• Follow the fridge maker's published instructions for removal and insertion; ensure the filter seats and locks fully.
• Flush several glasses of water after installation to clear trapped air and carbon fines.
• Check for leaks at the filter housing and connections before finishing.