Parts for Frigidaire FAC105T1A2: 03 - Recommended Spare Parts

This replacement louver directs and controls airflow inside the refrigerator, helping maintain even temperature distribution and proper circulation. It restores a damaged or missing vent to improve cooling performance and reduce drafts. What it does:

• Guides chilled air into the cabinet to support consistent cooling
• Replaces cracked, warped, or broken louvers that block airflow
• Helps reduce uneven temperatures and warm spots near the vent
• Stops rattling or vibration caused by loose or damaged louvers

• One replacement louver

• Disconnect power to the appliance before beginning any repair
• Remove the old louver carefully to avoid damaging surrounding trim
• Typically secures with clips or screws; basic hand tools may be required

This control panel is the front console that provides the oven/range user interface, mounting for the display and controls, and the connection point for the range's control electronics. Replaces a cracked, damaged, or nonresponsive console to restore normal operation and appearance. What it does

• Provides the user interface for setting bake/ broil/ timer and oven functions
• Houses the display and touchpads/controls and secures the underlying control electronics
• Restores responsive buttons or touch controls when the bezel or console is damaged
• Addresses visible damage, broken mounting tabs, or cosmetic wear on the front console

• Disconnect power to the appliance before beginning any work to avoid shock risk.
• Remove any trim or mounting screws to access the console; take care with clips and alignment tabs.
• Reconnect any ribbon cables or wire harnesses securely; avoid bending contacts.

This thermistor is the refrigerator temperature sensor that helps the control board monitor and regulate cooling. Replacing a failed thermistor restores accurate temperature readings for more consistent fridge and freezer performance. What it does:

• Senses internal air temperature and sends that information to the control board
• Helps the defrost and compressor cycles run at the correct times
• Commonly linked to symptoms like inconsistent temperatures, error codes, or a unit that runs constantly
• Does not control cooling directly but provides the temperature feedback the system needs

• Always disconnect power to the appliance before beginning service
• Typically located in the fresh food or freezer compartment near the evaporator
• Handle the sensor and wiring gently; avoid pulling on the wires or bending the probe sharply
• If troubleshooting, verify wiring and sensor resistance per the manufacturer's service instructions before replacement

A replacement start/run capacitor that helps the refrigerator's motor(s) get up to speed for reliable cooling and circulation. Restores proper motor starting when the original capacitor has failed. What it does:

• Provides the electrical boost needed for compressor and fan motors to start and run smoothly
• Commonly replaced when motors hum, fail to start, or fridge cooling is inconsistent
• Helps prevent motor overloads and repeated hard-start cycling when functioning correctly
• Matches the original part's role in the appliance's electrical starting circuit

• Disconnect power to the appliance at the breaker before servicing
• Discharge the capacitor before touching terminals to avoid shock; use insulated tools
• Verify terminal orientation and secure wire connections; do not force fit

This replacement water tube routes water between the dispenser and ice maker, restoring proper fill and drainage flow. It helps stop leaks and ensures the ice maker and dispenser receive water as intended. What it does:

• Channels water from the supply line to the ice maker/dispenser assembly
• Restores proper fill to the ice maker so ice production resumes
• Prevents water leaks and dripping when properly installed
• Can help stop no-fill or slow-fill symptoms when the original tube is damaged or kinked

• Disconnect power and shut off the water supply before beginning work.
• Access may require removing the refrigerator rear/inside panel or dispenser access panel.
• Inspect and reuse or replace any clamps, gaskets, or fittings as needed; tighten connections to prevent leaks.

Replacement evaporator fan blade that moves cold air across the evaporator coil and through the refrigerator compartments to help maintain even temperatures. Restores airflow to reduce warm spots and improve overall cooling consistency. What it does:

• Spins on the evaporator fan motor to circulate cold air through the freezer and fresh-food sections.
• Restores proper airflow when the original blade is cracked, warped, or broken.
• Common symptoms prompting replacement: reduced or uneven cooling, rattling/scraping noises from the freezer, or visible blade damage.
• Helps prevent excessive frost buildup by maintaining steady airflow over the evaporator.

• Disconnect power to the appliance before beginning any service.
• Handle the blade carefully; edges and broken pieces can be sharp.
• Ensure the blade is fully seated on the motor shaft and any retaining hardware is reinstalled per the OEM's guidance.

Mounting hardware, screws