Parts for Electrolux FGWC4633SS: 02 - Recommended Spares Parts

This hinge secures and lets the refrigerator door pivot smoothly so the door opens and closes correctly. Replacing a worn hinge restores proper door alignment and sealing for reliable cooling and easy operation. What it does:

• Provides the pivot point that supports and guides the refrigerator door
• Keeps the door aligned to maintain the cabinet seal and even closing
• Stops door sagging or misalignment that can cause gaps or rubbing
• Eliminates clicking, squeaking, or stiff movement when the hinge is worn

• Unplug the appliance or turn off power to avoid electrical hazards before starting
• Support the door while removing/installing the hinge to prevent damage or injury
• Use proper-size tools and follow torque guidance from the manufacturer; do not overtighten
• After installation, check door alignment and gasket seal; adjust as needed for an even gap

Replacement trim piece for wine cooler exterior or interior finish. Restores appearance when original trim is cracked, chipped, or missing.

Replacement door hinge for wine cooler. Installs on cabinet to support door opening and closing. Needed when original hinge is cracked or broken.

If your wine cooler runs too warm or too cold, this temperature sensor may have failed. Restores accurate temperature control and stable cooling cycles.

Wine cooler running warm or making loud noises? This fan assembly keeps air circulating for even cooling. Moderate DIY repair, typically 30-45 minutes.

This replacement cover is a factory-style access panel that protects internal components and restores the appliance's finished appearance. It keeps wiring and controls shielded while helping reduce noise and drafts. What it does

• Protects internal components from dust, spills and accidental contact
• Restores a damaged, cracked or missing panel for a finished look
• Helps eliminate rattles or vibration caused by a loose or broken cover
• Keeps seals and fasteners in place to maintain proper airflow around components

• Disconnect power to the appliance before starting any repair
• Remove any screws or clips holding the old cover, note fastener locations
• Align cover tabs and secure with original screws or clips; do not overtighten
• If access requires removing adjacent panels, keep track of all fasteners and wiring

Control board fixes wine cooler that won't cool, has blank display, or won't respond to buttons. Restores temperature control and display functions.

This is a genuine replacement mounting screw designed to secure appliance panels and small components. Installing the correct screw restores proper fit and reduces rattling or loose parts for safe, reliable operation. What it does:

• Secures panels, brackets, or small components to the appliance chassis
• Restores proper alignment and fit where a screw is missing or damaged
• Helps stop rattling, vibration, or loose parts caused by a stripped or lost fastener
• Simple, direct replacement when the original screw is worn or corroded

• Use the matching screwdriver or bit to avoid stripping the head
• Power off and unplug the appliance before accessing internal panels
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic
• Replace with the exact fastener type and length shown in your appliance's parts list

Replacement door handle for wine and beverage coolers. Restores safe, easy grip when original handle is cracked, broken, or worn. Matches factory mounting.

Control panel overlay for wine coolers. Replaces worn, faded, or peeling overlays on the front control interface. Direct replacement part.

Replace your wine cooler's door trim if it's cracked, chipped, or missing. This decorative trim piece frames the door glass for a finished appearance.

Replacement door hinge for wine cooler. Installs on cabinet to support door weight and allow smooth opening and closing. Needed when hinge is bent or broken.

Leveling foot for wine coolers. Installs at the base corner to support and level the unit. Replace if broken, cracked, or missing to restore stability.

Replaces a worn or damaged wine cooler door hinge to restore proper alignment and smooth operation. Install when door sags or doesn't seal evenly. Verify fit with your model number.

A flat metal washer used with fasteners to distribute load and protect appliance surfaces. Replaces a worn or missing washer to help maintain secure connections and reduce loosening from vibration. What it does:

• Provides a stable bearing surface for screws, bolts, and nuts
• Distributes clamping force to prevent damage to parts and panels
• Helps reduce fastener loosening from vibration or movement
• Restores proper fit where a missing or damaged washer causes wobble or gaps

• One flat washer

• Turn off and unplug the appliance before servicing
• Use the correct torque for the fastener to avoid crushing the washer

Wine cooler not cooling properly or making unusual noise? This fan assembly circulates air to maintain consistent temperature throughout your unit.

This replacement tray catches and channels defrost and condensation water inside the freezer compartment to help prevent leaks and water pooling. It restores proper drainage and helps keep the interior dry. What it does:

• Collects defrost and condensation water and directs it to the drain area
• Prevents water from pooling under food and components
• Supports and positions internal components in the drain area as designed
• Helps reduce odors and ice buildup caused by standing water

• One tray

• Disconnect power to the appliance before servicing
• Remove contents and any shelving/panels that block access to the tray
• Replace the tray in the same orientation; secure any retaining clips or screws as originally installed
• Inspect drain tube and surrounding seals for debris or damage and clean before reassembly