Parts for Kitchenaid KBFO42FTX06: 07 - Refrigerator Door Parts

Reduces contaminants for cleaner, better-tasting water and ice. Replace every 6 months or when indicator light activates. Verify fit by model number.

Seals the refrigerator door to prevent warm air from entering and cold air from escaping. Replace if torn, cracked, or no longer sealing properly.

Replaces a bent, worn, or damaged refrigerator door hinge. Restores smooth pivot action and proper door alignment for even gasket seal contact.

Replaces a bent, worn, or damaged refrigerator door hinge. Restores smooth pivot action and proper door alignment for even gasket seal contact.

The Screw is an OEM part for Whirlpool refrigerators. This screw plays a small but important structural role, securely fastening the refrigerator door hinges in place.

Causes of a bad screw include normal wear and tear, repeated door opening/closing stress, or accidental damage during cleaning or servicing of the hinge area.

Symptoms of a bad hinge screw include:

• Loose or sagging door that does not close or seal properly
• Increased vibration or noise from the hinge area
• Difficulty opening/closing the door smoothly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Replace a cracked, broken, or missing utility door bin for the center position of your refrigerator door. Restores organized storage for condiments.

Replacement door hinge for your refrigerator. Install when door sags, won't close properly, or pivot point is worn. Confirm fit with your model number.

Replacement door hinge for bottom-mount refrigerators. Mounts the door to the cabinet. Replace if cracked, bent, or causing misalignment issues.

Stainless steel corner trim for bottom-mount refrigerators. Replaces cracked, chipped, or missing decorative trim pieces on cabinet corners.

Trim cover cap for refrigerators. Installs on exterior panels to conceal screws and provide a finished look. Replace if cracked, broken, or missing.

Left-hand endcap trim anchors the rail for refrigerator bins and shelves. Replace this bracket if cracked, broken, or missing to restore proper support.

Right-hand end cap that secures the refrigerator door bin trim. Replace this plastic trim piece if cracked, broken, or missing to restore a flush fit.

Refrigerator door trim piece that covers the edge or gap along the refrigerator door. Needed when original trim is cracked, broken, or missing.

Replacement trim piece for refrigerator door edges. Installs along door perimeter to provide finished appearance. Needed when original is cracked or missing.

Decorative door trim piece for refrigerator. Installs along the door edge to provide a finished appearance. Replace if cracked, chipped, or missing.

This door bearing fits the washer door assembly to restore smooth opening and closing and reduce noise, wobble, or binding. Replacing a worn bearing helps maintain proper door alignment for reliable operation. What it does:

• Supports the door hinge so the door pivots smoothly without sagging or sticking
• Reduces squeaks, grinding, or rough movement when opening or closing the door
• Helps keep the door aligned to reduce stress on the latch and door seal
• Addresses symptoms like door wobble, uneven closing, or noisy operation

• Disconnect power (and water if accessing near waterlines) before starting any repair
• Removing the door panel or inner door trim may be required; retain all fasteners and document their locations
• Inspect surrounding parts (hinge, seal, latch) and replace if damaged; improper alignment can cause premature wear

Top hinge bushing provides smooth door support and movement. Replace if cracked, worn, or causing door misalignment. Installs at top refrigerator hinge.

Stainless steel screw that secures the back panel to the side panel of your dryer cabinet. Replace if screw is stripped, missing, or corroded.

Secures refrigerator door shelf bins in place for easy removal during cleaning. Replace if cracked, broken, or missing to restore proper bin engagement.

Cantilever door bin mounts on inner door rails to hold bottles, jars, and condiments. Replace cracked, broken, or missing bins to restore organized storage.

Replaces the small hinged cover on your refrigerator door's dairy or utility bin. Install when original door is cracked, broken, or missing.

This rail secures and guides the washer lid, restoring proper lid alignment and smooth opening/closing. Replaces a worn, cracked, or loose lid rail to reduce rattling and prevent the lid from catching during use. What it does:

• Provides a stable mounting surface for the washer lid so it opens and closes evenly
• Guides lid movement and helps prevent misalignment or binding
• Reduces noise and rattling caused by a loose or damaged rail
• Helps keep the lid seated correctly to prevent accidental gaps or snags

• Typical install requires removing the top or accessing the lid hinge area; retain original fasteners unless replacements are provided
• Disconnect power to the appliance before starting work to avoid injury

Seals your refrigerator utility bin to contain contents and prevent moisture transfer and odors. Replace if bin feels loose or leaks occur. Confirm fit with your model number before ordering.