Parts for Frigidaire FFSC2315LS0: 05 - Refrigierator Door Parts

This single-pack Frigidaire PureSource 3 WF3CB Water Filter is an OEM replacement part for Frigidaire refrigerators. It improves the quality and taste of your drinking water. It removes impurities such as lead, cysts, and mercury, as well as reduces chlorine taste and odor. The filter is NSF and WQA certified and is designed to fit specific side-by-side models after 2009 where the filter is located in the back, right top. 

Specs:

• Pressure range: 30 - 100 PSIG
• Color: White
• Dimensions: Approximately 2-1/2 inches in diameter by 9-1/2 inches deep.

To ensure optimal performance, filters should be changed every 6 months or 200 gallons, depending on usage. 

This gray magnetic refrigerator door gasket replaces the perimeter seal on the fresh food door. It creates an airtight closure that keeps cold air in, blocks humid air, and helps prevent temperature swings, frost, and condensation. What it does:

• Seals the door perimeter with a flexible magnetic edge to stop air leaks
• Helps maintain proper refrigerator temperature and reduce frost/condensation near the door
• Restores smooth closing when the old gasket is torn, shrunken, or warped
• Typical symptoms: visible gaps, moisture on the gasket, frequent cycling, or food warming near the door

• 1 gray magnetic refrigerator door gasket

• Disconnect power before servicing
• Warm the new gasket with a hair dryer or hot water to relax folds for easier seating
• Remove the old gasket; press/fasten the new gasket evenly into the door channel or retainer, ensuring corners are fully engaged
• Close the door and check for uniform contact; adjust hinges or gently reshape with warm air as needed and allow the gasket to set with the door closed

The Can Rack is an OEM part for Frigidaire refrigerators. It provides shelving located internally for organized storage of canned drinks. The can rack creates additional capacity within the refrigerator compartment above other sliding shelves and drawers.

Causes of a bad can rack can include being damaged from accidental impacts if heavy items are dropped onto it from above over time.

Symptoms of a bad can rack include:

• Bent or misshapen wires that no longer securely hold cans
• Broken off sections that reduce usable shelf space
• Loose assembly unable to be positioned properly on refrigerator walls

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models. 

This dairy door is the flip-up cover for the refrigerator's dairy compartment on the fresh-food door. It keeps butter and cheese covered and contained, restoring a clean, finished look when the original cover is cracked or missing.

• Covers the dairy compartment and hinges open for easy access
• Helps keep small dairy items contained and organized on the door
• Replaces a cracked, warped, discolored, loose, or missing cover
• Closes properly when seated on the original hinge posts

• Disconnect power before servicing
• Remove the old cover by releasing its tabs from the hinge posts
• Align the new cover with the hinge posts and press to snap into place
• Avoid forcing brittle plastic; allow the part to reach room temperature before installation

This refrigerator door stop limits how far the door swings open. Replacing a worn or broken stop restores the correct opening range, protecting the hinge and nearby cabinets while keeping door movement smooth and controlled.

• Mounts at the hinge to limit door swing and prevent overextension
• Protects the door, hinge, and adjacent cabinetry from impact damage
• Helps maintain proper door alignment and smooth operation
• Typical symptoms: door opens too far, bangs into surroundings, or the stop is visibly cracked/missing

• Disconnect power and clear items from the door before starting
• Support the door; remove hinge cover/fasteners and the damaged stop
• Install the new stop in the same orientation; tighten screws securely
• Reassemble and test the door swing to ensure it stops smoothly

This outer refrigerator door panel replaces a damaged or dented door to restore appearance, seal performance, and proper operation of the fridge compartment. It's a full external door panel designed to mount in place of the original. What it does:

• Replaces a dented, scratched, or warped outer refrigerator door panel to improve cabinet appearance
• Restores alignment so the gasket can seal properly and help maintain cooling performance
• Provides the correct mounting surfaces for handles, hinges, and trim so existing hardware reattaches
• Matches the original OEM fit and finish for a factory appearance

• One outer refrigerator door panel

• Handle existing door weight and support the door while removing and installing hinges to avoid damage or injury
• Transfer existing hardware (hinges, handle, trim, shelves) only if specified by the OEM instructions
• Tighten hinge fasteners to manufacturer torque recommendations; check door alignment and gasket sealing after installation

This #10-32 x 3/4-inch machine screw secures appliance components such as panels, brackets, and handles. Using the correct length and thread helps restore a snug, rattle-free hold wherever this screw is specified by the manufacturer.

• Fastens components with a #10-32 machine thread and 3/4-inch length
• Helps keep panels, trim, brackets, or handles secured and aligned
• Replaces missing, stripped, or corroded hardware
• Common signs include loose or wobbly parts, rattling, missing screws, or damaged screw heads/threads

• Disconnect power before servicing; if working near a water connection, shut off the water supply
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping plastic or threads
• Reuse any model-specific washers or spacers if present

This hinge bearing supports and guides the refrigerator door as it pivots on the hinge, reducing friction and wear. Replacing a worn bearing restores smooth, quiet door movement and proper alignment for a reliable seal.

• Provides a low-friction pivot surface between the hinge pin and the door
• Helps support door weight and maintain alignment for proper gasket contact
• Common symptoms of a worn bearing: squeaking or popping, door sagging or binding, and doors that don't close smoothly or seal consistently
• Reduces hinge wear to help extend hinge life

• Disconnect power and remove items from the door for safety and easier handling
• Support the door, remove hinge cover and fasteners, and lift the door off the hinge
• Remove the worn bearing and install the new bearing in the same orientation on the hinge pin or seat
• Reinstall and align the door; tighten hardware and verify smooth movement and proper gasket seal

The Upper Hinge Bearing is an OEM replacement part for Frigidaire refrigerators. It facilitates the smooth and quiet opening and closing. By reducing friction at the hinge point, it ensures the door operates seamlessly and is less prone to wear over time.

Causes of a faulty upper hinge bearing include repetitive stress and wear from continuous door opening and closing over time. Exposure to moisture may accelerate bearing degradation.

Symptoms of a bad upper hinge bearing include:

• Squeaking or grinding noises emitted from the hinge area
• Difficult door operation requiring increased lifting force
• Potential misalignment compromising door seal integrity

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This door bin (also called a door shelf) mounts to the inner door panel and holds bottles, jars, and condiments. Replacing a cracked or missing bin restores storage capacity and keeps items upright when you open and close the door.

• Adds organized storage space on the door for frequently used items
• Attaches to molded rails/tabs to hold contents securely during door movement
• Replace if the bin is cracked, warped, or the retaining hooks are broken
• Common symptoms: bin falls off, won't stay in place, items slide out, or the bin is missing

• Unplug the appliance before servicing
• Lift the old bin straight up and out of the door-liner tabs; transfer contents
• Align the new bin with the same slots and press down firmly until fully seated
• Distribute weight evenly and avoid overloading after installation

The Door Bin is an OEM replacement part for Frigidaire refrigerators. Mounted on the fresh food compartment door, the white bin provides storage for snacks and beverages.

Causes of needing replacement include cracks or fractures over time from repeated loading/unloading of contents. Warping plastic that no longer securely clips into door rails is also remedied.

Symptoms of a failing bin consist of:

• Items freely sliding around uncontained during opening/closing of the door
• Difficulty completely emptying or accessing corners for cleaning
• Inability to re-secure basket into floor rails keeping it attached

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore ranges.

The Door Bin is an OEM replacement part specific to Frigidaire-brand refrigerator doors. As an interior storage component, the door bin provides convenient access to commonly used items. 

Symptoms of a damaged or worn door bin include:

• Warping, cracks, or splits develop in the plastic material
• Detached or loose hinges prevent secure attachment 
• Items inside shifting or falling out during opening/closing

Causes involve repeated opening/closing stresses over time weakening the plastic. Temperature fluctuations from door openings also affect integrity.

This genuine Frigidaire door bin is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement part is a set screw, and it is intended for use in different types of appliances. This is a genuine replacement part made by Frigidaire. This screw set is compatible in many different areas of the appliance. Screws are typically used for keeping parts of the machinery secure and in place. It is possible that screws can become loose over time and need to be replaced. A new screw set might be needed if the user notices parts of the appliances are becoming loose or are falling off. This can be due to screws becoming stripped over time or if the appliance is bumped during transport. It is typically easy to replace screws. Simply remove the old screw and replace it with a new part. The only tools needed for this repair are a screwdriver and possibly pliers if the damaged screw is stuck in place.Note that this is a genuine OEM replacement part and is sourced from the manufacturer. This set screw is sold individually.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.