Maytag Washer A902 Leaking

The Mounting Stem Repair Kit is an OEM part for Whirlpool washing machines. It includes all necessary components to repair the mounting stem, which is a critical part of the washer's tub support system. Comes with the hub assembly, seal, and spanner nut. 6-2040130 should also be replaced at the same time. A spanner wrench is required to complete the repair TB123B.

Symptoms of a bad mounting stem include:

• Excessive noise or vibration during the spin cycle.
• The washer tub appearing loose or off-balance.
• Leakage around the central area of the washer, indicating a possible seal failure.

Causes of a bad mounting stem can include wear and tear from normal usage, especially with heavy loads, or corrosion and material fatigue that weaken the stem's integrity.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Tub Bearing Kit is an OEM part for Whirlpool washers. It includes all the necessary components to replace the tub bearing which is responsible for supporting the inner tub and allowing it to spin smoothly during the wash cycle. Over time, the bearing may wear out or become damaged, leading to excessive noise, vibrations, or even leaks from the washer.

Causes of a bad tub bearing can include regular wear and tear, exposure to heavy loads or unbalanced loads that put excessive strain on the bearing, or damage due to water leaks.

Symptoms of a bad tub bearing include:

• Excessive noise or grinding during the wash cycle.
• Vibrations or shaking of the washer.
• Leaks from the washer, around the tub area.
• The inner tub not spinning or becoming stuck.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Note: It is advised to replace the Mounting Stem Repair Kit, part number 6-2040130 at the same time.  To complete the repair, you’ll also need a Spanner Wrench to complete the repair (TB123B).

The Washer Drain Pump is an OEM part for Whirlpool washing machines. It is responsible for removing water from the washing machine during the drain cycle, ensuring efficient and complete water removal.

Causes of a bad drain pump can include blockages from debris or foreign objects, electrical failures, or wear and tear from regular use. Over time, these issues can impede the pump's ability to function properly.

Symptoms of a bad drain pump include:

• Water not draining from the washer
• Unusual noises during the drain cycle
• Error codes related to draining issues
• Leaks coming from the pump area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: Fits 2 belt design Maytag washers. Check belts for wear; if needed order 12112425.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

This internal hose connects the washer's outer tub to the drain pump, channeling wash water during the drain cycle. Replacing a worn or leaking hose helps prevent puddles and supports reliable draining performance.

• Routes water from the outer tub to the drain pump inside the washer
• Maintains a sealed path; cracks or loose connections can lead to leaks
• Visible splits, soft spots, swelling, or aging can cause water under the unit
• Obstructions or internal collapse may contribute to slow or incomplete draining

• Disconnect power and turn off water supply before servicing
• Expect residual water; use towels or a pan when removing the old hose
• Note hose routing and clamp positions; seat fully on each port and secure with appropriate clamps
• Run a quick fill/drain test and check all connections for leaks after installation

This replacement seal restores a tight, leak-resistant barrier between mating parts inside your appliance. Replacing a hardened or damaged seal helps stop seepage and keeps the system operating as designed. What it does:

• Forms a tight barrier between components to contain fluids and prevent leaks
• Helps maintain proper pressure/flow at the sealed joint
• Reduces risk of moisture damage around the connection point
• Common signs it's worn: drips or puddles, dampness around the joint, musty odors, visible cracking or flattening of the old seal

• 1 seal

• Disconnect power and shut off water or gas supplies before servicing
• Access the sealed joint; remove the old seal and clean mating surfaces thoroughly
• Lightly lubricate with manufacturer-approved lubricant; install without twisting
• Reassemble, restore utilities, and check closely for leaks during initial operation

This small retaining clip secures components in place inside the appliance, helping prevent movement, vibration, and premature wear. Replace a bent, fatigued, or missing clip to restore a solid, factory-tight hold.

• Holds panels, brackets, or tubing securely in their mounts
• Helps maintain alignment to reduce rattles, rubbing, or intermittent issues
• Common signs of failure: missing clip, loose fit, buzzing/vibration, parts that won't stay seated
• Restores proper retention after service, transport, or vibration-related fatigue

• Disconnect power and shut off gas/water before servicing
• Note the original clip's orientation; remove with needle-nose pliers
• Seat the new clip fully—do not over-bend; spring tension provides the hold
• Test operation before reassembly

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

This small clamping nut secures a mating clamp or bracket so the connected component stays firmly in place. Replacing a worn, stripped, or missing nut restores a solid hold and helps prevent looseness or leaks around the secured area.

• Secures a clamp or bracket to its mounting point
• Restores proper clamping force when the original nut is stripped or missing
• Common signs: loose clamp, rattling/vibration, clamp won't tighten, minor leaks where the clamp is used
• Durable hardware replacement to maintain stable, reliable assemblies

• Disconnect power and shut off water/gas to the appliance before service
• Note clamp/bracket orientation before removal for correct reassembly
• Start threads by hand to prevent cross-threading; then tighten with the appropriate tool
• Do not overtighten—snug just enough to securely clamp the component

This retaining washer secures a center-mounted component within the assembly, keeping parts aligned and in place during operation. Replacing a worn or missing washer helps prevent looseness, vibration, and noise for more reliable performance. What it does:

• Holds a component on a center shaft or stud to prevent axial movement
• Maintains proper alignment under rotation and load
• Can reduce wobble, rattling, or scraping noises from a shifting assembly
• In applicable washers, can help restore consistent agitation or spin when parts have been moving out of place

• 1 retaining washer

• Disconnect power and water before servicing; wear cut-resistant gloves
• Note the order and orientation of all spacers, washers, and clips during disassembly
• Clean mating surfaces and ensure the washer is fully seated before reassembly
• Inspect adjacent hardware for wear or damage and replace as needed

This agitator seal assembly sits at the agitator/drive-shaft pass-through to keep wash water inside the tub and away from the drive system. Replacing a worn seal helps stop center-post leaks and protects internal components from moisture.

• Seals the opening where the agitator/drive shaft passes through the tub or centerpost
• Helps prevent water from migrating into the centerpost/gearcase area
• Supports reliable agitation and spin by keeping contaminants out of the drive assembly
• Common symptoms of failure: water leaking from the center of the tub or beneath the washer, or rust/water tracks around the agitator hub

• Disconnect power and shut off water; wear gloves and eye protection
• Remove agitator cap and fastener, then lift the agitator to access the seal (procedure varies by model)
• Note the original seal orientation; clean mating surfaces and install the new seal squarely (lightly lubricate only if specified by the manufacturer)
• Reassemble and run a short fill/agitate test while observing for leaks