Maytag Washer LAT8024AAE Leaking

This repair kit contains seals and components needed to fix leaks around the washer's tub mounting stem. It prevents water from escaping the wash basket area during operation. Use this kit when you notice water pooling under your washer or leaking from the tub assembly.

Prevents backflow of drain water into fresh water supply. Mounts on top of washer. Replace if cracked, leaking, or damaged to restore proper drainage.

Supports the inner tub for smooth spinning during wash cycles. Replace when you hear grinding noise or see water leaking from bottom center of tub.

The Washer Drain Pump is an OEM part for Whirlpool washing machines. It is responsible for removing water from the washing machine during the drain cycle, ensuring efficient and complete water removal.

Causes of a bad drain pump can include blockages from debris or foreign objects, electrical failures, or wear and tear from regular use. Over time, these issues can impede the pump's ability to function properly.

Symptoms of a bad drain pump include:

• Water not draining from the washer
• Unusual noises during the drain cycle
• Error codes related to draining issues
• Leaks coming from the pump area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: Fits 2 belt design Maytag washers. Check belts for wear; if needed order 12112425.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

Washer not filling or filling slowly? The water inlet valve controls water flow into your machine. Common DIY repair takes 30 minutes with basic tools.

The Water Injector is an OEM part for Whirlpool washing machines. This component is responsible for distributing water into the washing machine during the wash cycle, ensuring that clothes are thoroughly saturated and cleaned. It connects to the water supply and directs water into the tub at the appropriate times.

Common causes of a bad water injector include blockages from mineral deposits, wear and tear from frequent use, or damage due to high water pressure. Over time, the injector's effectiveness can diminish, impacting the washing machine's performance.

Symptoms of a bad water injector include:

• Insufficient water entering the washing machine
• Longer fill times or failure to fill at all
• Poor cleaning performance
• Leaks or drips around the injector area

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Seals the tub cover to prevent leaks during wash and spin cycles. Replace if water leaks from the top of the tub. Confirm fit with your model number.

Leaking water at the tub ring during fill? This lower water injector channels incoming water into the tub. Simple 30-minute DIY repair with basic tools.

Fix water leaking onto the floor or uneven tub filling with this upper water injector. Directs inlet water cleanly into the tub. Easy DIY replacement.

Carries wastewater from your washer to the household drain. Replace if cracked, split, or leaking at connections to pump or drain standpipe.

Internal hose that channels water from the washer's outer tub to the drain pump. Replace if cracked, leaking, or worn to prevent puddles under the machine.

Small metal clip that secures panels, brackets, or tubing in place inside appliances. Replace if bent, fatigued, or missing to restore secure mounting.

Replace this washer gasket seal to stop leaks between components. Worn gaskets cause water leakage and poor performance. Verify fit with your model.

This small clamping nut secures a mating clamp or bracket so the connected component stays firmly in place. Replacing a worn, stripped, or missing nut restores a solid hold and helps prevent looseness or leaks around the secured area.

• Secures a clamp or bracket to its mounting point
• Restores proper clamping force when the original nut is stripped or missing
• Common signs: loose clamp, rattling/vibration, clamp won't tighten, minor leaks where the clamp is used
• Durable hardware replacement to maintain stable, reliable assemblies

• Disconnect power and shut off water/gas to the appliance before service
• Note clamp/bracket orientation before removal for correct reassembly
• Start threads by hand to prevent cross-threading; then tighten with the appropriate tool
• Do not overtighten—snug just enough to securely clamp the component

Seals the top of the outer tub to prevent leaks and splashing. Replace if cracked, worn through, or gasket is compressed causing water to escape onto the floor.

90-degree drain connector that creates an air break in the drain path. Replace if cracked, broken, or leaking to restore proper water drainage.

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

Fix agitator wobble and excessive vibration with this retaining washer. Secures center-mounted components to prevent looseness and noise during operation.

Seals the agitator shaft opening to prevent leaks and protect internal components. Replace if you see water leaking from the center post during wash cycles.