Parts for Electrolux E46DD75ESS: 03 - Replacement Parts

This wiper blade is the replacement scraping blade that helps keep a surface clear so the appliance can operate properly. It restores the original wipe/clean action to reduce buildup and improve performance. What it does:

• Replaces a worn or damaged wiper blade that no longer makes proper contact
• Scrapes away water, debris or excess material from the intended surface
• Helps prevent leaks or malfunctions caused by poor surface contact
• Commonly needed when the existing blade is cracked, torn, or overly worn

• One wiper blade

• Shut off power to the appliance before starting any repair
• Inspect mounting area for damage and clean before installing the new blade
• Remove the old wiper carefully to avoid damaging nearby trim or components
• If the blade uses clips or screws, reinstall them securely but do not overtighten

Hood seal creates an airtight barrier for proper ventilation. Replace if worn, cracked, or causing air leaks. Verify fit with your model number before ordering.

Includes two mounted microswitches.

Hood fan won't turn off or respond to controls? The relay switch manages power to your ventilation motor. Simple 15-minute replacement restores control.

This wiring harness routes power and signals between fridge components so controls, lights and dispensers operate reliably. It restores lost connections and replaces damaged or corroded wiring for safer, consistent appliance operation. What it does

• Carries electrical power and signal connections between components and the main control
• Replaces frayed, damaged or intermittent wiring that can cause partial or total component failure
• Helps stop intermittent operation, lights or controls that don't respond, or shorts from exposed wires
• Matches OEM connector end-types and routing for a direct-replacement fit

• Disconnect power to the appliance before servicing to avoid shock or damage
• Compare connector types and routing to the original harness before installation
• Support components while disconnecting plugs; avoid pulling on wires directly
• Secure harness with existing clips or ties and test functions after reconnection

This flat washer secures and spaces fasteners in the appliance, helping distribute load and protect mating surfaces for a reliable connection. It's a small but important hardware piece used where bolts or screws need a stable bearing surface. What it does

• Provides an even bearing surface to prevent fastener pull-through and protect parts from damage
• Helps maintain correct spacing and alignment of assembled components
• Reduces loosening by distributing clamping force from bolts or screws
• Commonly used with mounting brackets, housings, and assemblies that require a secure fastener interface

• Disconnect power to the appliance before beginning any repair
• Use the matching fastener size and replace any damaged hardware for proper fit
• Inspect surrounding parts (bolts, mating surfaces) and clean debris before installation

This screw is a direct-replacement mounting fastener used to secure cooker and refrigerator trim, panels, or internal components. Replacing a missing or damaged screw restores proper fit and reduces rattling or loose panels. What it does

• Secures trim, panel, or interior components in place to maintain proper alignment and fit
• Stops vibration noise and prevents parts from shifting during use
• Helps restore safe, stable assembly when an original screw is missing or stripped

• Disconnect power or unplug the appliance before accessing internal parts
• Use the correct-size screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-tightening which can crack plastic or strip threads
• Keep removed fasteners in a labeled container to prevent loss during repair

This small retaining nut secures appliance components to their mounts, keeping assemblies stable and preventing unwanted movement. It's a simple replacement that restores proper fit where a worn or missing nut causes looseness. What it does

• Fastens and secures mating parts to prevent movement or separation
• Replaces stripped, corroded, or missing nuts that cause rattling or loose panels
• Restores proper tension where a missing nut allows assemblies to shift
• Works as a threaded connector for bolts or studs in the specified location

• Disconnect power and any water supply before accessing internal components when applicable
• Match nut thread and orientation to the bolt or stud before tightening
• Use appropriately sized hand tools; avoid over-tightening which can strip threads
• If rusted or seized, apply penetrating lubricant and proceed carefully to avoid damage

This wiring harness routes power and signal connections inside the refrigerator to restore electrical continuity and reliable operation. It replaces a damaged or frayed factory harness to help re-establish proper component connections. What it does:

• Links the refrigerator's electrical components (compressor, fans, lights, controls) so they receive power and signals
• Replaces broken, melted, or corroded wiring that can cause intermittent operation or complete failure
• Helps stop symptoms such as lights not working, fans not running, or the compressor failing to start when caused by a faulty harness
• Prevents potential arcing or shorts from damaged insulation when installed as a like-for-like replacement

• Always disconnect power to the appliance before starting work to avoid shock or injury
• Compare the replacement harness to the original to ensure connector types and wire routing match before installing
• Route and secure the harness following OEM clips and channels to avoid pinch points or contact with hot surfaces

This is a replacement mounting nut used to secure appliance components and restore a snug, reliable connection. A simple fastener that helps stop loose parts and rattling caused by worn or missing nuts. What it does

• Secures panels, brackets, or hardware to keep components aligned and stable
• Restores proper fastening where a nut has become stripped, corroded, or lost
• Helps eliminate vibration noise and intermittent contact caused by loose hardware
• Works as a direct-fit replacement for the OEM nut used on compatible Frigidaire appliances

• Hand-start the threads, then tighten with the appropriate wrench to avoid cross-threading
• If hardware is corroded or threads are damaged, replace the mating bolt/stud as needed
• Disconnect power to the appliance if accessing electrical components or internal assemblies

This electrical harness routes power and control signals between appliance components to restore reliable operation. It replaces damaged or worn wiring that can cause intermittent or failed component function and helps prevent electrical faults. What it does:

• Replaces torn, frayed, or burnt wiring that interrupts power or signals
• Restores reliable operation to controls, motors, valves, or sensors
• Can resolve intermittent operation, components that won't run, or sporadic failures
• Reduces risk of arcing or shorted circuits from damaged wires

• Always disconnect power before servicing to avoid shock or injury
• Verify connector orientation and fully seat each plug for reliable contact
• Route and secure harness away from sharp edges, heat sources, and moving parts