Parts for Ge AEH18DPH1: 01 - Room Air Conditioner Parts

This is the air filter assembly for select GE room air conditioners. It traps dust and lint before they reach the evaporator coil, helping maintain airflow and cooling performance.

• Captures airborne dust and lint to protect the coil and blower
• Helps maintain steady airflow and cooling efficiency
• Replace if cracked, warped, missing, or won't stay seated
• Common symptoms include reduced airflow and visible debris on the filter

• Unplug the unit before servicing
• Remove the front grille or filter access panel; slide the old filter out
• Install the new filter with airflow orientation matching the original
• Clean surrounding surfaces and reinstall grille before powering on

This Air Guide Frame helps direct airflow inside the appliance so exhaust and cooling air follow the correct path, protecting internal components and helping the unit vent properly. It's a direct-replacement exterior frame piece. What it does:

• Guides and channels air through the appliance's venting area to maintain proper airflow.
• Holds surrounding trim and ducting in position for a secure fit.
• A damaged or warped frame can cause restricted airflow, rattling, or misaligned trim.
• Restores proper airflow routing when replacing cracked, broken, or bent frames.

• One air guide frame

• Disconnect power (and gas, if applicable) before starting any repair.
• Remove surrounding trim or panels as required to access the frame; keep fasteners for reassembly.
• Inspect adjacent ducts, seals, and mounting tabs for damage and replace if needed.

This nut-washer secures appliance assemblies where a captive nut and flat washer are needed, helping keep fasteners tight during normal operation. It's a small replacement part that prevents loosening and maintains proper component alignment. What it does:

• Acts as a combined nut and washer to fasten components and distribute load
• Keeps threaded connections from backing off due to vibration
• Restores secure attachment when the original nut-washer is damaged, stripped, or missing
• Commonly replaced when assemblies wobble, rattle, or come loose

• One nut-washer

• Disconnect power and unplug the appliance before beginning any repair
• Use the proper screwdriver or socket to avoid rounding the fastener
• If threads are damaged, replace the mating screw or stud rather than over-tightening

A small flat washer used as a replacement fastening spacer that helps secure bolts and prevent metal-to-metal wear. Restores proper spacing and fastener tension so assemblies stay aligned and tight. What it does:

• Acts as a spacer and load-distribution surface under a bolt or nut
• Prevents fasteners from loosening and reduces metal wear at contact points
• Restores correct alignment where a missing or worn washer caused vibration or rattling
• Simple, durable replacement for worn or corroded washers in mechanical assemblies

• Disconnect power before servicing electrical appliances to avoid shock
• Use appropriate hand tools; replace with the same style and thickness for correct fit
• Inspect mating fasteners and surfaces; replace any damaged hardware

This 10 mm-diameter gasket provides a precise seal to prevent leaks and maintain proper operation of the appliance connection where it installs. Durable construction helps restore a tight, reliable seal. What it does:

• Creates a watertight/airtight seal at the mating joint to prevent leaks
• Helps maintain proper pressure and function of the connected component
• Replaces worn, cracked or flattened seals that can cause drips or loss of performance
• Restores reliable sealing to reduce cycling or moisture-related issues

• Disconnect power and shut off water supply before starting any repair
• Inspect mating surfaces and clean away residue to ensure a proper seal
• Replace the old gasket fully; do not stretch excessively when installing
• After installation, restore power/water and check the connection for leaks

A replacement cooling fan motor that circulates air to help maintain proper appliance temperature and performance. Installs in appliances that use a small electric motor-driven fan to move air across coils or compartments. What it does

• Spins the appliance fan blades to promote airflow over coils, vents, or heat exchangers.
• Helps the compressor and cooling system run efficiently by improving heat transfer.
• Common symptom of failure: noisy operation, reduced or no airflow, or the appliance running warmer than normal.

• One fan motor.

• Disconnect power before servicing to avoid shock or injury.
• Match mounting orientation and connector type to the original motor.
• Handle wiring and fan blades carefully to avoid damage; secure all fasteners and wire connections.

This spring washer provides resilient tension to help keep screws and bolts from loosening on appliance assemblies. It's a simple replacement part that restores proper fastener tension and helps maintain secure connections. What it does:

• Applies spring force around a fastener to resist vibration-related loosening
• Commonly used on panels, brackets, and components that see movement or vibration
• Can reduce rattling and intermittent connection issues caused by loose hardware
• Works with 6 mm-diameter fasteners where a small lock-style washer is required

• Disconnect power and unplug the appliance before servicing
• Use the correct 6 mm fastener and proper orientation when reinstalling
• Tighten hardware to the OEM's recommended torque if available; avoid overtightening
• If other fasteners or parts are damaged, replace them to ensure a secure repair

A small mounting nut used to secure components and panels on compatible appliances. Replaces a loose or missing nut to restore stable, safe fastening and reduce rattling or wobble. What it does:

• Secures panels, brackets, or assemblies to the appliance frame
• Prevents fasteners from backing out during normal operation
• Helps stop rattling, vibration noise, and loose-fitting parts
• Restores proper alignment for attached components

• Disconnect power and water before beginning any repair
• Match threads and size before installation; hand-start the nut to avoid cross-threading
• Tighten securely with the correct socket or wrench, but do not overtighten
• If the original fastener was damaged, replace the mating bolt/stud as needed

This axial flow fan moves air through the appliance to help cool internal components and support proper airflow. Replacing a worn or damaged fan restores quiet operation and helps prevent overheating-related issues. What it does:

• Circulates air across internal components or heat exchangers to maintain proper operating temperatures
• Helps prevent overheating of electronics, motors, or heating elements
• Reduces abnormal noise caused by worn or imbalanced fan blades or bearings
• Supports consistent airflow for reliable appliance performance

• One axial flow fan assembly

• Disconnect power to the appliance before starting any repair
• Handle the fan blades carefully to avoid damage; align properly during installation
• Verify secure mounting and electrical connections before restoring power
• Test appliance operation after installation and observe for proper airflow and quiet operation

This 8 mm diameter gasket creates a reliable seal in appliance assemblies to help prevent leaks and loss of pressure or airflow. It's a small replacement part that restores proper sealing where a worn gasket is causing issues. What it does:

• Seals joints and connections to help prevent water or air leaks
• Restores tight fit where a cracked, brittle, or flattened gasket allows seepage
• Reduces vibration noise from loose or poorly sealed parts
• Helps maintain proper operation of the sealed compartment or fluid path

• One 8 mm diameter gasket

• Disconnect power and water supply (when applicable) before servicing the appliance
• Remove old gasket and thoroughly clean mating surfaces before installing the new gasket
• Ensure the gasket is fully seated and aligned along the entire contact surface for an effective seal

A small circular rubber gasket designed to provide a reliable seal where a 8 mm diameter gasket is specified. Helps prevent air, moisture, or dust from passing through a joint or opening in the appliance. What it does:

• Creates a tight seal around shafts, openings, or mating surfaces to reduce leaks and drafts
• Cushions and protects components from vibration and wear
• Helps maintain correct airflow or pressure paths inside the appliance
• Common replacement when a worn or cracked seal causes unwanted noise, moisture, or air loss

• One 8 mm diameter gasket

• Inspect mating surfaces and clean thoroughly before installing the new gasket
• Replace only with the exact gasket size specified for your appliance to ensure proper sealing
• If adhesive or a retainer is used, follow the appliance manufacturer's instructions for secure attachment
• Disconnect power or follow appliance safety procedures before servicing

This M8 nut secures components to an M8 stud or bolt, restoring a firm mechanical connection. Use it to replace a missing, stripped, or loose fastener so panels and brackets stay properly attached. What it does:

• Threads onto an M8 bolt or stud to lock parts together.
• Prevents components from working loose due to vibration.
• Commonly used on brackets, mounts and assemblies that require an M8 fastener.
• Replacing a worn or missing nut can stop rattling, movement, or misalignment.

• Disconnect power and follow appliance safety procedures before servicing.
• Use the correct sized wrench or socket to avoid rounding the nut.
• Tighten to the manufacturer's recommended torque where available; do not overtighten.
• Inspect mating bolt/stud threads and replace if damaged.

This curtain assembly replaces a damaged or missing door trim curtain to restore proper fit and protect internal components while improving appearance. It's a direct-replacement component used on compatible GE appliances. What it does:

• Covers and protects internal door/frame openings to keep components shielded from debris and light
• Helps maintain correct door alignment and trim fit for smooth opening and closing
• Reduces rattling or vibrating noises caused by a loose or broken curtain piece
• Restores finished appearance when the original curtain is cracked, warped, or missing

• One curtain assembly

• Disconnect power to the appliance before starting any repair
• Installation typically requires removal of the outer door or trim panel and basic hand tools
• Handle parts carefully to avoid scratching trim or damaging clips; keep fasteners organized for reassembly

This support to cabinet is a metal mounting bracket that secures the appliance to surrounding cabinetry for stable, rattle-free operation. It helps keep the unit aligned and prevents shifting or sagging during normal use. What it does:

• Anchors the appliance to the cabinet frame to maintain proper alignment and fit
• Reduces vibration and rattling caused by loose or worn fasteners
• Prevents the appliance from tilting or shifting when doors or controls are used
• Restores safe, stable mounting after damage or corrosion to the original bracket

• Disconnect power (and gas if applicable) and remove surrounding trim before starting
• Retain or replace mounting hardware as needed; use screws appropriate for cabinet material
• Position bracket squarely against cabinet and appliance mounting points, then tighten securely

This top guide secures and helps align the dishwasher's upper rack for smooth sliding and reliable operation. It prevents the rack from binding or coming off the track, restoring normal loading and unloading performance. What it does:

• Guides and stabilizes the upper rack as it moves in and out
• Keeps the rack properly aligned to prevent tipping or jamming
• Reduces wear on the rack rollers and track by maintaining correct alignment
• Helps ensure dishes load and unload smoothly without shifting

• One top guide

• Designed for straightforward replacement; remove the upper rack to access the guide
• Inspect the track and rollers for damage and clean before installing
• Use basic hand tools; avoid forcing plastic tabs to prevent breakage
• Disconnect power and follow appliance safety guidelines before servicing

This molded form gasket provides a replacement seal designed to restore a tight closure and reduce air or water leakage. It helps maintain proper appliance operation by replacing a worn or damaged seal. What it does:

• Seals the mating surface to prevent air or water from leaking out
• Helps reduce frost build-up or moisture-related pooling when the seal is compromised
• Restores door/compartment closure where a deformed or torn gasket allows gaps
• Commonly replaced when gasket shows visible cracks, gaps, or continual leaks

• Disconnect power and remove any stored items before replacing the gasket
• Clean and dry the sealing surface thoroughly to ensure a proper fit
• Align the gasket into the channel and press evenly; some trims may require careful seating along the entire edge
• Inspect surrounding trim and hardware; replace or tighten as needed for a complete seal

This Form Gasket 2 is a replacement sealing gasket designed to restore a tight, reliable seal where the original foam/form gasket has become compressed or damaged. Replacing it helps reduce leaks and maintain normal appliance operation. What it does:

• Replaces a worn or damaged foam/form gasket to restore proper sealing
• Helps prevent water, air, or debris from passing where the original gasket seals
• Commonly used where a formed seal cushions or closes a gap in the appliance assembly
• Address symptoms such as visible gaps, leaks, rattling, or improper sealing along the joint

• One Form Gasket 2 as shown

• Install in clean, dry area; remove old gasket and clean mating surfaces before fitting the new gasket
• Fit gasket to the formed channel or mounting surface per the appliance's service instructions
• Wear gloves to protect hands from sharp edges and to avoid contaminating the gasket surface

This PCB box sub-assembly is the housing that protects and secures the appliance control electronics, helping keep the control board stable and shielded from debris and moisture for reliable operation. What it does:

• Provides a protective enclosure and mounting for the main control PCB
• Helps prevent shorting and physical damage to the control board
• Supports secure connector alignment to maintain electrical connections
• Common symptom: appliance exhibits control board-related faults, loose connectors, or intermittent operation

• Disconnect power to the appliance before servicing to avoid shock or damage.
• Handle the control board and housing carefully; avoid static discharge and bending circuit board components.
• Basic hand tools are usually required; follow the appliance service manual for panel removal and reassembly.

This replacement power cord restores electrical connection to compatible GE appliances so the unit powers on safely and reliably. Use it when the original cord is damaged, frayed, or no longer providing consistent power. What it does:

• Replaces a worn or damaged mains cord to restore power to the appliance
• Stops issues caused by frayed wires, exposed conductors, or loose connections
• Helps eliminate intermittent power, arcing at the plug, or visible cord damage
• Works as the direct electrical connection between the appliance and household outlet

• Always unplug the appliance or shut off breaker power before servicing
• Basic hand tools may be required to remove access panels and secure wiring terminals
• Confirm cord orientation and terminal connections match the original; tighten terminals firmly

This thermostat is the temperature control for room air conditioners. It senses temperature and cycles the compressor to maintain your set comfort level, helping restore consistent cooling when the original control becomes inaccurate or fails. What it does:

• Monitors temperature and opens/closes contacts to start and stop the compressor
• Helps the unit reach and maintain the temperature you select
• Helps resolve symptoms such as: AC won't turn on/off at the dial setting, runs continuously, short-cycles, or temperature adjustments have little effect
• Direct-fit replacement designed for the original mounting location

• 1 thermostat

• Disconnect power before servicing to avoid electrical shock
• Access the control panel; note wire locations and transfer any mounting hardware from the old part
• If your model uses a capillary sensing tube, route it exactly as original and secure in clips; do not kink or sharply bend it
• Reassemble, align the control knob, and test operation across several temperature settings

This is the main control board that manages the appliance's electronic functions and user interface, restoring normal control of cycles, displays, and timed operations. Replaces a failed or unresponsive control module to recover device control. What it does:

• Receives input from buttons/knobs and sends commands to motors, valves, heaters, and displays
• Controls timing, cycle selection, and system diagnostics for normal operation
• Resolves issues like unresponsive controls, no display, or incorrect cycle behavior
• Requires correct configuration and secure connections to function reliably

• 1 main control board (electronic control assembly)

• Disconnect power before service to avoid shock or damage
• Handle board by edges and avoid contact with components or circuitry
• Verify mounting, connectors, and wire routing match original before restoring power

This replacement transformer supplies the correct voltage for an appliance's control circuits so electronic controls and low-voltage components receive stable power. Installs in place of a failed or damaged transformer to restore reliable control operation. What it does:

• Converts incoming mains power to the lower voltage used by control boards and low-voltage components
• Restores power to electronic controls and displays when a failed transformer prevents operation
• Helps resolve symptoms like dead control panels, no display, or intermittent control function
• Provides a direct, plug-in replacement for the corresponding OEM transformer

• Disconnect power to the appliance before starting any repair to avoid electric shock
• Label or photograph wire connections before removal to ensure correct reassembly
• Mount securely and reconnect wires exactly as original; use appropriate wire connectors

This capacitor clamp is a small metal bracket that secures a refrigerator or appliance capacitor to the cabinet, helping keep the capacitor stable and preventing movement or vibration during operation. It preserves reliable electrical connections and reduces noise from loose components. What it does

• Holds the capacitor firmly in place to prevent shifting and rattling
• Helps maintain stable capacitor connections to avoid intermittent motor or control issues
• Reduces vibration-related noise from the capacitor area
• Protects the capacitor from contact with other components that could cause wear or damage

• One capacitor clamp/mounting bracket

• Disconnect power before accessing electrical components
• Inspect the clamp for cracks, corrosion, or missing fasteners and replace if damaged
• Retain original mounting hardware when possible; use compatible screws or bolts if replacements are needed

This sensor support is a small mounting bracket that secures an appliance sensor in the correct position for reliable readings and consistent operation. It replaces a worn or broken bracket to restore proper sensor placement. What it does:

• Holds the sensor firmly in place to help maintain accurate measurements
• Prevents sensor movement or vibration that can cause inconsistent readings
• Helps reduce false error codes related to misaligned sensors
• Restores proper sensor positioning after accidental damage or wear

• One sensor support mounting bracket

• Disconnect power to the appliance before beginning any repair
• Handle the sensor and wiring gently; avoid pulling on wires or connectors
• Ensure the sensor is seated in the bracket in the correct orientation before reassembly
• Use the existing fasteners or clips; do not overtighten plastic parts