Parts for Lg LSN092CE: Room A / C Parts

This DC stepping motor assembly drives precise, incremental movement in the appliance's subsystem to restore correct mechanical positioning and timing. Replacing a failed stepping motor brings back accurate, repeatable motion and reduces related errors. What it does:

• Converts electrical signals into precise, step-wise rotation for controlled mechanical movement
• Restores accurate positioning when the appliance stops mid-cycle or fails to advance
• Can stop intermittent operation, humming, or lack of movement caused by a faulty motor
• Clears related error codes or cycle faults that point to motor or position problems

• One complete DC stepping motor assembly

• Disconnect power before servicing to avoid shock or short circuits
• Verify the motor harness connector and orientation before removal and reinstallation
• Handle the motor and gear interfaces carefully to avoid damage to mating parts

This replacement remote control restores convenient, across-the-room operation of your air conditioner. Replace a lost, damaged, or unresponsive remote to regain reliable control of power, temperature, and modes without touching the unit.

• Sends commands to the air conditioner's receiver to adjust power, temperature, mode, and fan settings
• Common fix for no response to button presses, intermittent control, or needing to stand very close to the unit
• Restores normal operation when the original remote is lost, cracked, or has worn-out buttons

• Install fresh batteries with correct polarity (+/-)
• Aim the remote at the unit's receiver with a clear line of sight; remove obstructions
• If the unit does not respond, replace batteries and power-cycle the A/C before further diagnosis

The Blower Wheel Bearing is an OEM part for LG air conditioners. This bearing supports the blower wheel, ensuring smooth rotation and efficient airflow throughout the unit. 

Causes of a bad blower wheel bearing can include wear and tear from regular use, lack of lubrication, or damage from debris or impact. 

Symptoms of a bad blower wheel bearing include:

• Unusual grinding or squealing noises from the blower area
• Reduced airflow or diminished cooling efficiency
• The blower wheel wobbling or vibrating excessively
• The fan motor struggling to start or run smoothly

This OEM LG part is also compatible with some Kenmore models.

The Blower Wheel Bearing is an OEM part for LG air conditioners. This bearing supports the blower wheel, ensuring smooth rotation and efficient airflow throughout the unit. 

Causes of a bad blower wheel bearing can include wear and tear from regular use, lack of lubrication, or damage from debris or impact. 

Symptoms of a bad blower wheel bearing include:

• Unusual grinding or squealing noises from the blower area
• Reduced airflow or diminished cooling efficiency
• The blower wheel wobbling or vibrating excessively
• The fan motor struggling to start or run smoothly

This OEM LG part is also compatible with some Kenmore models.

This cross-flow fan assembly circulates air through the appliance's cooling compartment to help maintain even temperatures and consistent airflow. Replacing a faulty fan restores proper cooling performance and reduces abnormal noise. What it does:

• Moves air across the evaporator and through the cabinet to promote even cooling and defrost efficiency
• Helps prevent warm spots and uneven temperatures in the compartment
• Stops or reduces abnormal rattling, buzzing, or whining when the original fan motor or blade fails
• Supports normal defrost cycles by maintaining steady airflow over evaporator surfaces

• Disconnect power before beginning any repair to avoid shock or injury
• Handle the fan and nearby evaporator coils carefully to avoid bending fins or damaging the motor connector
• Verify mounting orientation and connector alignment; reuse existing screws/clips unless replacements are specified

This installation plate assembly provides the mounting surface needed to secure internal components and align parts during appliance installation or service. It restores proper support where the original plate is damaged or missing. What it does:

• Provides a stable mounting surface for internal components and assemblies
• Keeps components aligned to prevent rubbing, vibration, or misalignment
• Replaces bent, cracked, or corroded installation plates that compromise fit
• Helps ensure panels and covers sit flush after reassembly

• One installation plate assembly

• Designed to install in the factory mounting location—verify orientation before tightening fasteners
• Use the original screws or OEM-recommended fasteners and torque to prevent stripping
• Disconnect power (and gas or water where applicable) before servicing the appliance