Dryer Latch Switch Parts

This replacement switch restores reliable on/off signaling to the circuit it controls, helping your appliance start, stop, and respond correctly. A worn switch can cause intermittent operation, no response, or lights and functions that don't activate. What it does:

• Provides an electrical open/closed signal to enable functions like starting a cycle, powering a motor or light, or shutting a feature off
• Acts as a safety/position interlock (such as door, lid, float, or hood) depending on the model
• Typical symptoms include won't start, won't stop, light won't turn on/off, or intermittent operation
• Can be checked with a multimeter for continuity when actuated

• 1 switch

• Disconnect power before servicing; turn off gas or water supply if applicable
• Access the switch, note wire locations, and transfer leads one at a time to the new switch
• Mount securely, ensure the actuator aligns and wires aren't pinched
• Reassemble and test operation before finalizing

The Dryer Door Switch is an OEM replacement part for GE dryers. The door switch is a key safety mechanism that monitors whether the door is closed during operation. The switch automatically stops the dryer cycle if the door is opened, preventing heat from escaping and potential safety hazards.

Causes of a bad door switch can be related to wear and tear over time, damage from excessive bending of the wires, or moisture infiltration that causes corrosion of internal components.

Symptoms of a bad door switch include:

• The dryer fails to stop or start when the door is opened or closed
• Error codes or failure indications related to the door switch

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Color: metallic. Measures about 1 inch high by 2 inches deep.

This fixed-value resistor is an electrical component used in select dryers to limit current in a specific control circuit. It helps the timer or electronic control operate correctly by dropping voltage to safe, design-intended levels.

• Provides precise resistance to reduce voltage/current in the designated dryer circuit
• Supports proper operation of the timer, control board, or end-of-cycle signal (varies by model)
• Failure may present as a timer that won't advance, an inoperative signal/buzzer, or irregular cycle behavior
• Replace if visibly burned/damaged or if testing shows an open or shorted condition

• Disconnect power to the appliance before servicing
• Access the console/wiring harness and note original wire routing
• Make secure, insulated connections and route the resistor/leads exactly as original to avoid heat or chafing
• After installation, run a test cycle to ensure proper operation of the affected function

This dryer temperature selector switch lets you choose between four heat settings for proper fabric care. Replacing a worn switch restores accurate temperature selection so loads dry evenly without overdrying delicate items.

• Controls the dryer's heat level across four selectable settings
• Faulty switch can cause incorrect temperatures or only one setting to work
• May lead to poor drying performance or fabric damage if not functioning
• Restores reliable temperature selection and consistent drying results

• Unplug dryer before servicing; shut off gas if applicable
• Pull control knob straight off to access the switch
• Transfer wires one at a time to the new switch to maintain correct positions
• Ensure switch shaft and flat align with the knob during reassembly

This replacement door switch restores proper door sensing in your refrigerator. It detects when the fresh food or freezer door opens and closes, turning interior lights on/off and signaling the control so door-ajar alerts and related features work correctly. What it does:

• Senses door position to control interior lighting
• Sends door status to the control in many models for features like door-ajar alerts or fan pause
• Helps prevent overheating near the light by ensuring it turns off when the door is closed
• Common symptoms of failure: no interior light, light stays on, flickering light, or persistent door-ajar alarm

• 1 door switch

• Disconnect power to the refrigerator before servicing
• Carefully release the old switch from the cabinet opening and unplug the wire harness
• Connect the harness to the new switch, orient correctly, and snap or seat it fully in the opening
• Restore power and verify proper light operation and door-ajar indication

This is a refrigerator door switch. It signals the control when a door is opened or closed to turn interior lights on/off and may pause certain functions. Replacing a faulty switch restores proper lighting and door-activated operation.

• Senses door open/close to control interior lighting
• A failed switch can cause lights to stay on, never come on, or flicker
• May also affect features that depend on door status
• Common signs include no interior light or light remaining on with door closed

• Unplug power before servicing
• Access the switch at the door jamb; gently pry out the old switch
• Transfer and reconnect wiring one terminal at a time to the new switch
• Ensure the switch seats flush and test door operation before closing up

Rotary temperature switch 4 position.

This door switch detects whether the appliance door is open or closed. A working switch lets the machine start when the door is fully shut and stops operation when the door opens for safety.

• Monitors door position and allows the cycle to run only when closed
• Interrupts power to stop operation when the door opens
• Common symptoms of a failing switch: appliance won't start with the door closed, must press/hold the door to run, interior light stuck on/off, or a "door open" message on models with a display

• Disconnect power to the appliance before servicing
• Access the switch at the door opening/front panel; release mounting screws or locking tabs and remove the switch
• Move wires to the new switch one at a time to maintain correct positions
• After reassembly, test switch operation before running a cycle

Rotary tempurature switch, four position.

The Locker Assembly is an OEM component specifically designed for LG electric dryers. Found behind the dryer door, this assembly houses door-locking mechanics. 

Causes of a bad locker can include wear and tear over time, damage due to impact, or unintentional stress on components.

Symptoms of a faulty locker assembly include:

• The dryer door not latching securely in the closed position  
• Gaps or air leaks are visible around the door seal when running
• The door is unable to stay shut on its weight  
• Loud clicking or grinding noises from the door area

This OEM LG part is also compatible with some Kenmore models.

This strike is the catch point the latch grabs to keep the appliance door securely closed during operation. Replacing a worn or broken strike restores reliable latching so cycles can start and run properly. What it does:

• Engages with the door latch to hold the door closed during use
• Helps ensure the control senses the door is closed
• Maintains proper alignment for smooth, consistent latching
• Typical symptoms: door won't latch or stay closed, "door open" message, cycle won't start, intermittent operation when the door is moved

• 1 door strike

• Disconnect power to the appliance before servicing
• Remove the existing strike and retain mounting hardware if reusable
• Position and secure the new strike; adjust so the latch engages without forcing
• Close and test the door for smooth engagement before running a cycle

This strike plate mounts at the door opening and works with the door latch/strike to keep the appliance door securely closed during operation. Replacing a worn plate helps restore positive latching and reliable cycle start/stop via the door switch.

• Provides the catch surface for the door latch/strike to engage
• Helps keep the door closed and properly aligned
• Enables the door switch to engage so the cycle can run
• Common symptoms include: door won't stay closed, door pops open, unit won't start unless the door is pressed, visible wear or bending on the plate

• Disconnect power before servicing
• Open the door and remove the screws securing the existing plate
• Align the new plate with the latch/strike and fasten securely with the existing hardware
• Test door closure and latch engagement; adjust alignment if necessary

This start switch completes the dryer's start circuit when you press Start, energizing the motor to begin the cycle. Replacing a worn switch restores consistent, reliable starting when the original becomes intermittent or electrically open. What it does:

• Completes the start circuit to send power to the drive motor when Start is activated
• Common failure symptoms include the dryer not starting or no response when pressing Start
• May cause intermittent starts that require multiple presses or jiggling
• Switch may feel loose or show heat discoloration at the terminals

• Includes 1 start switch

• Disconnect power to the dryer before servicing
• Access the control panel/console to reach the switch
• Label or photograph wire positions; transfer wires one at a time to the new switch
• Secure the switch, reassemble panels, restore power, and test start operation

This push-to-start switch momentarily closes the start circuit to begin a cycle. Replacing a worn switch restores reliable starting when you press the Start button.

• Initiates operation by closing the start circuit when pressed
• Works with the door switch and timer/control to begin a cycle
• Common symptoms: won't start when Start is pressed; runs only while the button is held; intermittent starting; Start button feels loose or sticky
• Also known as an on/off PTS or start button switch

• Disconnect power before servicing
• Access the console/control panel and remove the start knob or button if present
• Move wires to the new switch one at a time to maintain correct terminal positions
• Secure the switch in the panel, reassemble, and test Start function

Replacement striker for the refrigerator door latch that provides the catch point for the door to close securely. Restores proper door engagement to help maintain a tight seal and consistent internal temperature. What it does:

• Provides the catch point for the door latch so the door closes and stays latched
• Helps maintain an effective door seal to preserve cooling performance
• Common symptom: door won't stay closed, pops open, or fails to latch
• Also helps reduce drafts and noise caused by a misaligned latch

• Turn off power to the appliance before starting work
• Access the striker area, remove mounting fasteners, and replace with the new striker
• Align the striker so the latch engages smoothly; tighten screws securely
• Use care not to overtighten or strip mounting holes; replace damaged hardware as needed