Range Hood Run Vent Thermal Fuse Parts

The Run Capacitor is an OEM part for GE refrigerators. It plays a crucial role in the refrigerator's cooling system by providing the necessary start and run voltage to the compressor. Without a properly functioning run capacitor, your refrigerator may struggle to maintain the desired temperature, leading to spoiled food and inefficient energy use.

Causes of a bad run capacitor include electrical surges, wear and tear over time, or overheating due to a malfunctioning refrigerator compressor or poor ventilation.

Symptoms of a bad Run Capacitor include:

• The refrigerator compressor fails to start.
• Unusual humming noises coming from the refrigerator.
• The refrigerator cycles on and off more frequently than normal.
• A noticeable increase in energy consumption as the refrigerator struggles to maintain the proper temperature.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

Installation kit for range hoods. Includes mounting hardware and adapters needed to install your vent hood. Replace missing or damaged components.

Exterior cover that finishes and protects your range hood's vertical duct area. Replaces cracked, damaged, or missing chimney covers for a clean look.

This is a vent damper designed for use with a range hood exhaust system. It mounts in the ductwork and uses a gravity or spring-loaded flap to allow air to flow out while preventing outside air, drafts, and pests from entering when the hood is off. Replace this part if you notice cold drafts coming through the hood vent, the damper flap is stuck, or the existing damper no longer seals properly.

Replaces the vent flap in your range hood exhaust system. Install when the original damper is cracked, broken, or missing to restore airflow control.

This is an electrical wire lead used to restore or replace a damaged connection in the appliance. It provides a direct conductive path so motors, lights, or controls can receive power and signals reliably. What it does:

• Reconnects power or signal between components when the original wire is damaged or broken
• Restores functionality for motors, fans, lights, or switches that are losing power due to a faulty lead
• Prevents intermittent operation caused by frayed, corroded, or cut wiring
• Helps maintain safe electrical continuity when properly installed and secured

• One wire lead

• Disconnect mains power before inspecting or replacing wiring to avoid shock or injury
• Match wire color, connector type, and routing to the original; use proper crimps/terminals or solder and insulated sleeving
• Secure wire away from moving parts and heat sources; replace any damaged insulation or clips

Bottom duct extension for range hood ventilation systems. Replaces cracked, damaged, or missing duct components to restore proper airflow routing.

Upper chimney section for range hoods. Covers the ductwork between the hood and ceiling. Replace if damaged, dented, or missing during installation.

This is a metal duct connector plate designed to attach a 7-inch round duct to a range hood vent housing. It provides a secure transition between the hood exhaust outlet and the ductwork, often incorporating a damper function to prevent backdrafts. Replace this plate if you notice air leaking around the duct connection, a rattling noise during operation, or if the existing plate is damaged or corroded.

Range hood won't start or shuts off unexpectedly? A failed thermal cutoff fuse interrupts power when temperatures exceed safe limits. Simple repair.

Solid-state triac that switches AC power under command of the appliance's electronic control board. Replacing a failed triac restores proper power control to heating elements or motors and resolves intermittent or no-power symptoms. What it does:

• Acts as a solid-state switch on the control board to regulate AC power to heating elements or motors
• Enables the electronic control to modulate output for temperature or speed control
• Failure can cause no heat, intermittent heating, or loss of motor control
• Designed to match the original control circuit; check board mounting and connections before replacing

• Always disconnect all power at the breaker or unplug the appliance before servicing — risk of electric shock
• This part mounts to the control board; handle the board and connectors carefully to avoid damage
• Use anti-static precautions when handling electronic components;
• Verify the part number on the original board before installation

Backdraft damper flap for range hood exhaust outlet. Opens during venting, closes when off to block drafts and pests. Replace if cracked or broken.

This duct kit is used to convert a vented range hood into a recirculating configuration, typically including a charcoal filter and ductwork components. It allows the hood to filter air and recirculate it back into the kitchen when exterior venting is not available. Replace the kit if airflow from the hood has weakened, odors are no longer being filtered effectively, or the existing components are damaged.

Extends your range hood's duct cover chimney to fit taller ceilings. Replace a damaged, bent, or missing extension for a polished, finished look.