1064113710 Parts

This door bumper cushions the door against the frame to prevent metal-to-metal contact. Replacing a worn or missing bumper restores smooth, quieter closing and helps protect surfaces from chips, scuffs, and vibration.

• Absorbs impact where the door meets the cabinet/frame
• Reduces slamming noise and vibration during closing
• Helps protect paint, glass, and trim from wear
• Typical symptoms: missing/cracked bumper, loud clunk when closing, marks on frame, rattling

• Disconnect power and, if applicable, shut off gas/water; allow hot surfaces to cool
• Open the door to access the bumper location
• Remove the worn bumper and clean the contact area for proper seating
• Install the new bumper fully seated and aligned; test door operation

The Door Closer-Gravity is an OEM part for Whirlpool refrigerators. It is an assembly located on the top hinge side of the refrigerator door, responsible for providing controlled resistance when opening and closing the door.

Causes of a bad door closer can include worn or broken springs, a damaged sliding mechanism, or misaligned components from repeated use over time.

Symptoms of a bad door closer include:

• The door not staying open at the desired angle when accessing shelves and bins
• Excessive force required to open or close the door
• The door not fully closing or sealing against the cabinet

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement door bumper cushions the appliance door to reduce noise, prevent metal-on-metal contact, and protect the door finish. It restores smooth closing when the original bumper is worn, cracked, or missing. What it does:

• Cushions the door edge to prevent hard impacts and reduce slamming
• Dampens vibration and rattling that can occur when bumpers are worn
• Prevents metal-on-metal contact that can scratch or damage the door
• Helps keep the door aligned and closing smoothly

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Typically presses or snaps into a bumper mounting hole; remove the old bumper and press the new one into place.
• Inspect adjacent mounting holes and surrounding trim for damage while installing.

Replacement screw that secures panels, brackets, and other components inside your appliance, keeping assemblies tight and aligned. Replace missing or stripped hardware to eliminate looseness, reduce vibration, and restore a solid, factory-fit hold.

• Fastens panels, brackets, trim, or internal components
• Helps maintain alignment and reduce rattling/vibration
• Replaces missing, loose, rusted, or stripped hardware
• Common signs: stripped head/threads, loose panel, buzzing/rattling noises

• Disconnect power before service; shut off gas/water if applicable
• Match to the original screw; start threading by hand to avoid cross-threading
• Use the correct driver size to prevent stripping
• Tighten snugly; do not overtighten. If it won't hold, inspect the receiving hole/clip

The Diffuser is an OEM component specifically designed for Whirlpool refrigerators. Located inside the refrigerator compartment's rear wall, it evenly distributes cool air flow throughout storage shelves.

Causes of a bad diffuser include cracks developing from constant air blowing over many years. Debris buildup may also obstruct optimum air distribution.

Symptoms of a bad diffuser include:

• Warm or cool spots inside the refrigerator   
• Reduced airflow felt at storage level vents  
• Visible cracks or breaks in the plastic structure
• Buildup of dust or particles on air passages

This OEM Whirlpool replacement diffuser ensures balanced interior temperatures. Its engineered vent design supports consistent air distribution along shelves. 

Replace yours if any symptoms surface. This part is also compatible with some GE, Crosley, and select Kenmore models. 

Replacement mounting screw that secures panels, brackets, or internal components to restore a solid fit and reduce movement. Simple, direct replacement for a missing, stripped, or corroded fastener to help maintain safe appliance operation. What it does:

• Holds trim, panels, brackets or control assemblies in place to prevent rattling and misalignment.
• Replaces stripped, rusted, or missing screws that can cause loose parts or vibration.
• Restores proper component alignment for safe, stable appliance performance.
• Small, inexpensive fix that prevents further wear to attached parts when properly installed.

• Use the correct screwdriver or bit to avoid stripping the head; match size to the screw.
• Do not overtighten — snug is sufficient to secure parts without damaging threads or components.
• Disconnect power to the appliance before working near controls or wiring.
• Keep removed screws organized during disassembly so all fasteners are replaced.

This door bumper cushions and stabilizes the appliance door to reduce noise and wear from slamming. It helps the door close smoothly and maintain proper alignment for reliable operation. What it does:

• Absorbs impact to prevent metal-on-metal contact and reduce slamming noise
• Helps the door sit evenly to improve latch engagement and sealing
• Reduces vibration and rattling during operation
• Simple replacement that restores proper door feel and alignment

• Disconnect power to the appliance before starting any repair
• Access the bumper by opening the door; some models may require removing the door or inner panel
• Press or snap the bumper into the locating hole or slot until secure; replace any retaining clips if present

This is a replacement 8-18 threaded screw used to secure panels and components on compatible Whirlpool appliances. It restores proper fastening where a missing or damaged screw causes loose parts or vibration. What it does

• Fastens panels, brackets, and small assemblies to the appliance frame
• Replaces stripped, corroded, or missing screws that cause rattling or loose components
• Helps maintain proper alignment of panels and controls for safer operation
• Suitable where an 8-18 threaded machine screw is specified by the manufacturer

• One replacement screw

• Disconnect power to the appliance before service to prevent shock or injury
• Use the correct driver to avoid stripping the screw head; do not force mismatched tools
• Tighten until snug — avoid over-tightening which can strip threads or crack plastic
• If replacing multiple fasteners, check mating threads and replace any damaged clips or anchors as needed

This genuine replacement door handle restores a secure grip and factory appearance to your refrigerator door. Designed to match original fit and finish, it helps you open and close the door smoothly and reliably. What it does:

• Replaces a worn, cracked or broken refrigerator door handle
• Provides original-style grip and alignment for proper door operation
• Prevents accidental slips and improves everyday usability
• Restores cosmetic appearance to match the appliance's original finish

• One refrigerator door handle

• Remove power to the appliance and empty the door area before starting
• Typical installation uses screws or clips; keep original fasteners if re-using
• Tighten fasteners to secure handle without over-torquing to avoid cracking

This air baffle directs and controls cold airflow inside the refrigerator compartment to help maintain even temperatures and proper circulation. Replaces a cracked, warped, or missing baffle to restore intended airflow paths. What it does

• Directs cold air from the evaporator into the refrigerator compartment for balanced cooling.
• Helps prevent uneven temperatures and localized warm or cold spots.
• Reduces excessive airflow directly onto stored items that can cause freezing or drying.
• Can rattle or obstruct airflow when cracked or loose, causing noise or reduced performance.

• One air baffle

• Disconnect power to the appliance before beginning work.
• Installation typically requires removing shelves or drawers for access; handle plastic parts gently to avoid damage.
• Align tabs or tracks and snap the baffle into place; do not force or bend beyond natural fit.

This cover assembly protects the appliance's internal unit compartment and helps keep wiring and components secure for reliable operation. It replaces a cracked, broken or missing compartment cover to restore proper protection. What it does:

• Protects internal components and wiring from debris and accidental contact
• Keeps the compartment secure and helps prevent loose or exposed parts
• Helps reduce airflow or lint intrusion into the unit cavity when installed
• Restores a proper fit when the original cover is damaged or missing

• One cover assembly

• Disconnect power (unplug or shut off breaker) before beginning work
• Basic hand tools typically required; remove fasteners or clips holding the old cover
• Align tabs and secure with original screws or clips; do not overtighten

This handle installation hardware kit supplies the mounting hardware needed to install a compatible appliance handle. Use it to replace missing or damaged fasteners so the handle mounts securely and functions as intended. What it does:

• Provides the mounting hardware required to attach a compatible appliance handle
• Replaces missing, stripped, or damaged screws, clips or brackets that prevent proper handle fit
• Restores secure handle attachment and reduces wobble or looseness
• Matches OEM mounting locations when used with the correct handle components

• Turn off power to the appliance before starting work and follow the appliance safety instructions
• Use only the supplied fasteners to avoid damage; tighten screws snugly but do not overtighten

Includes both right and left hand sides.