11025131410 Parts

Screw: 8-16 x 3/8 inch.

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening

Replace aging or leaking washer supply lines with this fill hose kit. It provides two 5-foot hoses to connect your home's hot and cold water valves to the washer, helping maintain a secure connection and consistent filling.

• Connects hot and cold water faucets to the washer's inlet valves
• Replace if hoses are leaking, cracked, bulging, or kinked
• Can help address slow filling caused by restricted or kinked hoses
• Useful when installing or relocating a washer

• Unplug the washer and shut off both water supply valves before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucet and washer
• Match hot to hot and cold to cold; hand-start threads to avoid cross-threading, then tighten firmly without overtightening
• Restore water and power; run a fill test and check all connections for leaks

This replacement power cord restores the electrical connection to your appliance so it can receive consistent power and operate safely. It's a direct-fit service part used when the original cord is damaged or no longer supplying power. What it does:

• Provides the main electrical connection from the wall outlet to the appliance
• Replaces frayed, cut, or melted cord insulation that can cause power loss or shorts
• Stops intermittent or no-power symptoms caused by a damaged cord
• Restores safe, reliable power delivery when the original cord is faulty

• Always disconnect power at the breaker or unplug the appliance before installation
• Route and secure the cord away from sharp edges, moving parts and high-heat areas

This electronic control board is the main control module that manages your appliance's user interface and timed functions, restoring normal operation when the original control becomes unresponsive or erratic. What it does:

• Replaces the appliance's failed/main control module that runs cycles, timing, and electronic commands
• Restores control of display, touchpad/knobs, and programmed cycles when the original board malfunctions
• Commonly used when the unit shows unresponsive controls, error codes, or intermittent operation related to the control board
• Works with the appliance's existing wiring harness and user interface

• One electronic control board

• Disconnect power to the appliance before attempting replacement to avoid shock or injury
• Handle the board by its edges and avoid touching components or connector pins to prevent static damage
• Verify connector locations and orientation before unplugging; take photos if needed to ensure correct reassembly

This machine screw secures components in place to maintain proper alignment and stability during appliance operation. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, noise, or loosening parts.

• Provides a secure mechanical fasten for panels, brackets, or internal assemblies
• Helps correct rattling, vibration, or loose-fitting parts
• Useful when an original screw is stripped, corroded, or lost
• Sized to match 8-18 thread applications in compatible units

• Disconnect power and shut off water or gas before servicing
• Note original screw location and orientation for correct reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• Replace any damaged clips or mounts the screw engages

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

5 foot. Package of 2.

Number-8, 18-thread screw used to secure panels, brackets and small assemblies in Whirlpool appliances. Replacing a missing or damaged screw restores secure mounting and helps stop rattling or loose parts. What it does:

• Fastens trim, panels, brackets or small appliance components that use a #8-18 threaded fastener
• Restores secure mounting when a screw is lost, stripped or damaged
• Helps eliminate vibration-related noise from loose parts
• Simple replacement part for basic fastening needs

• Disconnect power to the appliance before servicing and work on a cool, stable surface
• Use the correct screwdriver or driver bit to avoid cam-out or stripped heads
• Thread in straight and tighten until snug; do not over-torque to avoid stripping threads or damaging components
• Replace with the identical screw type and size for proper fit and function

This replacement 7-2-1 screw secures components in compatible Whirlpool appliances, providing a dependable fastener for panels and assemblies. Use it to restore proper fitment and reduce rattling or loose parts. What it does

• Fastens trim, panels, brackets, or internal assemblies to keep parts secure
• Helps stop vibration-related noise from loose components
• Restores correct mounting where the original screw is missing or damaged
• Matches the form and fit of the OEM fastener for intended attachment points

• One replacement 7-2-1 screw

• Use the correct driver to avoid stripping the screw head
• Hand-start threads before tightening to prevent cross-threading
• Tighten until snug—do not over-tighten to avoid damaging plastic or sheet-metal parts
• Disconnect power to the appliance before accessing internal areas

This heavy-duty replacement power cord restores the appliance's connection to household power, delivering reliable electrical continuity for normal operation. Ideal when the original cord is damaged, burned, or fails to supply power. What it does:

• Carries mains electricity from the wall outlet to the appliance so controls and heating elements can operate
• Replaces frayed, cracked, melted, or otherwise damaged cords that may cause intermittent power or no power
• Helps eliminate sparking, overheating, or visible insulation damage at the cord or plug
• Matches the OEM fit and wiring configuration for a direct replacement when compatible

• One power cord

• Disconnect power at the breaker or unplug the appliance before beginning any work
• Verify wiring color and connector orientation match the appliance before attaching
• Secure strain relief and routing to prevent pinching or chafing; tighten terminal connections firmly

This drain hose coupling connects two sections of the washer drain hose to restore a watertight path for wastewater, helping prevent leaks and restore proper draining. What it does:

• Joins two drain hose sections or connects hose to a mating outlet for secure water flow
• Seals the hose connection to reduce leaks at the joint
• Restores proper draining when a damaged or missing coupling causes slow drain or leakage
• Designed to fit the OEM hose profile for a snug, stable connection

• One drain hose coupling as shown

• Turn off power and water supply before starting any repair
• Inspect hose ends for damage; trim to clean cut if required for proper fit
• Push hose ends fully onto the coupling and secure with manufacturer-recommended clamps

This wire harness routes power and control signals between core appliance components to restore proper electrical connectivity and reliable operation. It's a direct-fit replacement that helps resolve faults caused by damaged or worn wiring. What it does:

• Carries power and control signals between the appliance control and internal components
• Restores lost or intermittent electrical connections that cause erratic operation
• Replaces frayed, burned or broken wiring that can trigger faults or component failure
• Helps stop symptoms such as components not powering, intermittent function, or error/fault lights linked to wiring issues

• Disconnect the appliance from power (unplug or switch off breaker) before starting
• Take photos of existing wire routing and connector positions to ensure correct reinstallation
• Match connectors and secure all terminal connections; avoid forcing connectors onto terminals
• Inspect related connectors and grounding points for damage; replace or repair as needed

This replacement top is the outer cabinet top panel that restores the dryer's finished appearance and provides a stable surface above the drum. It replaces damaged, dented or rusted tops to improve looks and protect internal components. What it does

• Covers and protects the top of the appliance cabinet from dents, spills and debris.
• Restores the appliance's finished appearance when the original top is scratched, dented or corroded.
• Helps maintain alignment of control and console assemblies that mount to the cabinet top.
• Prevents exposure of internal parts that can collect dust and lint.

• Disconnect power (and gas, if applicable) before starting any repair.
• Use proper tools to remove the control console and mounting screws; support the top panel while removing fasteners.
• Watch for sharp edges and wear gloves; follow OEM instructions for reassembly to ensure proper fit.

This factory fastener secures appliance panels and components for a tight, rattle-free fit. Replace a missing, stripped, or corroded screw to keep assemblies aligned and performing as intended.

• Fastens panels, brackets, or assemblies in place
• Helps reduce vibration and rattling caused by loose hardware
• Maintains proper alignment of parts to prevent premature wear
• Common signs you need it: missing screw, loose panel, vibration/buzzing noises, or hardware that won't tighten

• Disconnect power; for gas or water-connected appliances, shut off supply lines before service
• Match the screw to the original; verify size, length, and thread before installation
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Snug only—do not overtighten, especially into plastic or thin sheet metal

This cycle switch is the user-controlled selector that tells the washer which wash sequence to run, restoring normal cycle selection and operation. It provides a direct replacement for a worn or non-responsive cycle selector. What it does:

• Selects and routes electrical signals to start the chosen washer cycle
• Restores reliable selection when the dial won't change cycles or the machine won't advance
• Helps resolve intermittent or no-response issues from the cycle selector control
• Works as the mechanical/electrical interface between the user dial and the washer's control system

• (1) cycle switch (selector)

• Turn off and unplug the appliance before attempting any service
• Access may require removing the control console or rear panel; handle wires and connectors gently
• Only install parts that match the appliance's original part number