11028033701 Parts

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks

Cracked or broken washer lid preventing spin cycles? This lid assembly covers the tub opening and engages the safety switch. 10-minute DIY install.

This is a gray and white plastic control knob used on a dryer to select cycle settings or timer positions. It attaches to the control shaft on the front console panel. Replace this knob if it is cracked, broken, or if the D-shaped shaft opening is worn out and the knob spins freely without engaging the control.

Fix detergent not dispensing or leaking detergent with this washer dispenser assembly. Restores proper detergent flow during wash cycles.

Top spring hinge for washer lids. Provides tension and pivot support for smooth opening and alignment. Replace if cracked, broken, or causing lid sag.

This ground wire provides a safe chassis connection to restore proper grounding and reduce shock and electrical-fault risk. It replaces a frayed, corroded or missing ground lead to help keep the appliance electrically safe. What it does

• Connects the appliance chassis to the grounding system to prevent stray voltage on metal surfaces
• Restores a secure ground path if the original wire is broken, loose, or corroded
• Helps stop intermittent power faults or nuisance tripping caused by a compromised ground
• Addresses symptoms like visible wire damage, loose ground connection points, or grounding-related electrical issues

• One ground wire

• Always disconnect power (unplug or shut off the circuit breaker) before starting work
• Attach the ring/terminal ends to the designated chassis ground screw and the equipment ground point
• Route the wire away from moving parts, heating elements, and sharp edges; secure with existing clips or fasteners
• If terminal hardware is missing or damaged, replace with equivalent OEM-style fasteners and torque to specification

Color: White. Size: 1 qt. can. Acrylic appliance paint.

Replacement mounting screw for laundry center panels and brackets. Needed when original fastener is lost, stripped, or damaged during service work.

Suspension spring for washers. Supports the tub assembly during spin cycles. Replace if spring is stretched, broken, or detached from mount points.

Hex nut secures panels and components in your washer. Replace if missing, stripped, or corroded to restore proper assembly and stability during use.

Rubber bumper cushions washer components to reduce noise and vibration. Replace if cracked, worn, or missing to protect cabinet surfaces and keep panels aligned.

This is a genuine replacement mounting screw that secures appliance components and panels so parts stay aligned and stable. Installing the correct screw restores proper fit and helps eliminate vibration or loose panels. What it does:

• Fastens panels, brackets, or small components in place
• Replaces missing, stripped, or damaged screws that cause loose parts
• Helps stop rattling, vibration, or misaligned panels
• Restores secure connections after repairs or part replacement

• One mounting screw

• Unplug the appliance or disconnect power before starting work
• Use the correct screwdriver bit to avoid stripping the head
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic
• Keep removed hardware organized so you can reuse existing screws when applicable

This is a plastic cup that sits at the end of a suspension rod, acting as a snubber pad to absorb vibration and support the wash tub during the spin cycle. It helps dampen movement and reduce noise. Replace this part if the washer shakes excessively, makes loud banging noises during spin, or if the existing cup is cracked or worn out.