1104786291 Parts

This outer tub is the large stationary tub that holds water for the washer and supports the inner wash basket. It restores a watertight enclosure and structural support so your washer can fill, agitate, and drain properly. What it does:

• Forms the watertight basin that contains wash water and directs it to the drain
• Supports the inner tub/basket and helps keep the basket aligned during cycles
• Prevents water from leaking into the cabinet when intact
• A cracked, warped, or corroded outer tub can cause visible leaks, loud or uneven operation, and washer shutdowns

• One outer tub

• Disconnect power and water supply before beginning any repair
• Drain remaining water and remove the washer top/lid and control panel as needed to access the tub
• Support or remove the inner tub/basket per service manual instructions to avoid damage during removal
• Inspect and replace related seals, gaskets, and clamps as needed

This is a single replacement screw used to secure appliance panels and components. It restores proper fastening to help eliminate looseness and rattling and keep parts aligned for safe operation. What it does:

• Secures trim, panels or internal components to maintain proper alignment
• Prevents rattling or vibration caused by loose fasteners
• Replaces missing or stripped screws for safe, reliable fit
• Works wherever the OEM screw specification and fit match the original

• One screw as shown

• Disconnect power and/or gas before accessing internal components
• Use the proper driver size and avoid over-tightening to prevent thread damage
• Verify correct screw placement against the appliance's service diagram

The Tub Gasket is an OEM replacement part for Whirlpool washing machines. This gasket forms a crucial seal between the washer tub and the cabinet, both preventing water leaks and reducing noise and vibration. 

Causes of a bad tub gasket can include cracks, tears, or compression failures due to age, use, or impacts over time. Gaskets can also degrade with chemical exposure.

Symptoms of a bad tub gasket include:

• Water leaks from around the tub and cabinet interface 
• Excessive noise or vibration during spin and agitation cycles
• Reduced washer balance resulting in thumping or off-center loads

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

Drain hose retainer keeps the appliance's drain hose securely fastened to the cabinet or pump, helping prevent the hose from slipping loose. Replacing a broken retainer reduces leaks and improper draining caused by a detached hose. What it does:

• Secures the drain hose to the cabinet, pump outlet, or drain connection to maintain correct hose positioning.
• Helps prevent water leaks and hose disconnection during drain cycles.
• Common symptoms of a failed retainer: visible hose movement, water at the rear or floor, or intermittent draining issues.
• Replaces worn or broken retainers that no longer hold the hose firmly.

• Always disconnect power and turn off water before servicing the appliance.
• Access may require moving the appliance or removing a rear/access panel to reach the hose retainer.
• Seat the drain hose fully in its proper position, snap or clip the retainer into place, and verify the hose is secure and not kinked.
• Inspect the drain hose for cracks or wear while replacing the retainer; replace the hose if damaged.

This water inlet hose directs incoming water into the appliance for normal operation, providing a reliable pathway that maintains safe, consistent water flow. Use this OEM-fit hose to replace a cracked, leaking, or damaged inlet line. What it does

• Carries incoming water from the home's supply to the appliance's water valve or fill assembly.
• Restores proper filling when an old hose leaks, is split, or becomes deteriorated.
• Helps prevent water damage and maintains normal cycle performance when functioning correctly.
• Compatible with repairs where the original inlet hose is worn, kinked, or blocked.

• One new replacement water inlet hose.

• Disconnect power and shut off the water supply before starting any repair.
• Inspect hose fittings and seals; replace any worn clamps or gaskets for a secure, watertight connection.
• Route the hose without sharp bends or kinks and secure per the appliance's routing clips.

This power cord is the replacement electrical lead that supplies mains power to the appliance, restoring safe, reliable operation when the original cord is damaged or worn. What it does

• Delivers AC power from the wall outlet to the appliance's internal wiring and controls.
• Replaces frayed, cut, melted, or otherwise damaged cords that can cause intermittent power or safety hazards.
• Helps eliminate issues like no power, intermittent power loss, or visible cord insulation damage.
• Restores a secure connection at the appliance strain-relief and terminal block when installed correctly.

• One replacement power cord.

• Always disconnect power at the circuit breaker or unplug the appliance before installing.
• Inspect terminal block and strain-relief; replace any damaged hardware and secure the cord per the appliance wiring diagram.
• Follow the appliance manufacturer's wiring diagram for correct conductor routing and grounding.

This nozzle directs and focuses water flow inside the dishwasher so dishes get a thorough rinse. Replaces a worn, cracked, or clogged nozzle to restore spray coverage and help prevent poor cleaning performance. What it does

• Channels water from the spray arm or manifold to create a targeted spray pattern
• Helps maintain even water distribution across racks for better cleaning
• Clogs, cracks, or damage can cause weak spray or spotty wash results
• Compatible with systems that use a snap- or press-fit nozzle on the spray assembly

• Disconnect power and water supply before starting any repair
• Remove the spray arm or access panel as needed to reach the nozzle
• Inspect mating surfaces for debris; press or snap the new nozzle into place until seated

This replacement screw is a direct-fit fastening part used to secure panels and small components on compatible Whirlpool appliances. It restores proper fit and helps stop loose or rattling parts for reliable appliance operation. What it does:

• Secures trim, panels, or brackets to keep parts aligned and stable
• Prevents vibration-related noise caused by loose hardware
• Replaces missing or damaged screws that allow components to shift
• Restores factory fit where stripped or worn fasteners fail

• Disconnect power to the appliance before servicing to avoid electrical shock
• Use the proper screwdriver or driver bit to avoid stripping the head
• Install carefully and tighten until snug; do not overtighten
• Keep track of small parts and fasteners during disassembly

A small metal hose clamp that secures flexible hoses and tubing to fittings to help prevent leaks and keep connections tight. Simple, durable replacement for worn or loose clamps on appliance water and drain lines. What it does:

• Holds a hose or tube firmly on a barb or fitting to prevent leaks or disconnection
• Resists loosening from vibration and normal use
• Restores a secure connection when an old clamp is corroded, stretched, or broken
• Helps prevent water damage from loose plumbing connections

• One metal hose clamp

• Disconnect power and shut off water supply before servicing
• Slide clamp over hose, position over fitting barb, then compress or tighten as required
• Replace any damaged hoses or fittings when installing a new clamp
• Verify a leak-free connection before returning appliance to service

This wire harness routes electrical connections between components to restore reliable power and signal flow. It replaces a damaged or frayed harness to reduce connection faults and intermittent operation. What it does:

• Reconnects control, power, or sensor circuits to restore normal appliance operation
• Replaces damaged, burned, or broken wires and terminals that cause intermittent power or failures
• Helps eliminate arcing, shorts, or loose-connection symptoms like no-start, no-heat, or control unresponsiveness
• Maintains factory wiring layout and terminal arrangement for correct component communication

• Disconnect power to the appliance before starting any work to avoid electric shock
• Match wire colors and terminal styles to the original harness; secure connections firmly
• Inspect connectors, clips, and mounting points; replace any damaged hardware

Color: White. Size: 1 qt. can. Acrylic appliance paint.