Kenmore Washer 110.47852700 (11047852700, 110 47852700) Parts

• Will not drain

I have a 12 year old Kenmore Elite washer. One day, suddenly, I heard a grinding noise and the washer abruptly stopped. I called a repair service and was told it could be the bearings in the drum of this front-load washer, or it could be the washer's drain pump, which automatically shuts down when the drain pump fails. The repairman said, if it is the drum, it wasn't worth fixing for the age of this washer. It would cost $85 for him to come out and diagnose the problem, then if I decide to fix... Read more

• Leaking

Luckily we planned ahead when building the laundry room, as we built a water catch basin and drain under the washer, but waking up to see 1-2 inches of water is never a good sign - even if it is contained. It appears that a sleeve of a shirt was accidentally caught between the door mechanism and the bellow seal. After a few hundred revolutions in the washer, the shirt knotted up and was torn free of its pinch - in doing so, it tore a quarter sized hole in the rubber bellow seal. This was,... Read more

• No hot or cold water
• Will not stop filling with water
• Will not fill with water

I replaced the supply lines and mesh in-line filters. I made sure incoming water pressure was strong. I also cleared some debris from the internal drain filter down below. The F20 persisted. My plan was to start swapping out parts from the inlet on. I ordered the valve and got it in a day. Thanks to the schematics and videos on appliancepartspros.com, I was comfortable with the repair, and had confidence in my plan. The actual valve replacement took about 10 minutes. Bingo bango... Read more

• Lid or door won't close
• Lid or door will not open

I watched the AppliancePartsPros.com video on the part and replaced the hinge according to the video. Nothing could be easier. Read more

• Shakes and moves

We looked online at AppliancePartsPros.com under the symptoms and found it was most likely caused by the shocks. Of course there was a repair video showing how to replace all four shocks step by step, and there was a link for purchasing the four shocks at the bottom of the video. Our repair didn't go quite as quickly as on the video because we are novices, but we were able to do the repair ourselves and, once again, saved ourselves a ton of money! Now we have a very quiet washer and dryer again... Read more

• Will not fill with water
• Will not stop filling with water

This should be plastered all over the place and every owner of a front end washer should be advised or a recall should be issued about this. As I opened the top of my washer to fix a F35 error by replacing the water level switch, which worked out great and it fixed the issue, I noticed a rusting spot at the bottom of the washer just under where the motor is placed. After running the washer with the lid open (I don't recommend doing that) I noticed that it was coming from the top of the soap... Read more

First I check with Appliance Part Pros, watch videos how to access the parts I believe to be the problem. I love there videos and parts list of solutions to fix what it wrong. First I removed the washer from the laundry room and but it in the garage for more room to work on it. The next thing I replaced was the door lock which seem to be a possible cheap fix and does get a lot of abuse, however it was not the door lock and people should stop posting it could be this issue when they get a F06... Read more

• Burning smell
• Will not agitate
• Pumps but will not spin

I pulled the unit away from the wall and noticed black dust on the floor. Unplugged the unit, turned off the water. Removed back panel (about 10 screws with Torx heads) and noticed the belt was off, the drive pulley was loose and wobbling on the shaft, black dust all over the inside. Belt was worn along one side. Some grooves/damage in the outer drum casing around the pulley where it appeared the belt had rubbed. Removed the lower crossbar (2 more screws) to get better access to the drive... Read more

I used a directional video from AppliancePartsPros specifically made for my specific clothes washer. It made the repair quite simple. Read more

• Will not fill with water

After watching the YouTube video provided by Appliancepartspros and checking various forums I determined the dispenser motor had gone out. Turns out, it was a two part problem. The connectors to the motor, and the motor had corroded. Cleaned them both with vinegar. The old motor did a load before I started having problems with the CCU. I didn't learn about the CCU needing a reset under the quick diagnostics until after replacing the motor and the new part doing the same thing. Both the new... Read more

I used a directional video from AppliancePartsPros specifically made for my specific clothes washer. It made the repair quite simple. Read more

Repairing the problem was the easy part. Diagnosing the problem took a little more time. To diagnose the problem, it took longer because I first cleaned the Drain Pump trap from all the material it collected. Socks, hair pins, and other materials that were not cleaned from pants pockets. It then still did not drain. Repeated the process after finding more materials and a toy that punctured the hose between the tub and the drain pump. Running the drain and spin cycle takes about 11... Read more

Prior to ordering parts I had pulled the pump strainer basket and cleaned it out. There was both soft and hard scale build up. The tub-to-pump hose was also pretty crusty/slimey. Still got warnings for SUDS and repeated F02 errors. Ordered parts and replaced the pump, tub-to-pump hose, interior drain hose and exterior drain hose (both hoses has some slime build up). The water standing in the tub when I emptied it the first time had very little suds but we kept getting the SUDS warning. ... Read more

Ordered the springs and shocks. Noticed that the washer had placement for 4 springs, but the factory only installs 2 (or they forgot to install the other two on my machine). If you replace the springs, be sure to check for the spring bracket mount. You will also need those. The washer is running fine. Next I'll work on the dryer. Read more

Replaced It With New One Read more