11092575821 Parts

Almond. Size: 13 oz. can. Acrylic appliance paint.

Knurled pin secures knobs or dials to control shafts in washers. Replace if the original is missing, worn, or damaged to stop loose or spinning knobs.

Touch-up paint for appliances in almond color. Repairs chips, scratches, and worn spots on ovens, refrigerators, microwaves, and dryers.

Leaking washer during drain cycle? This drain hose clamp secures the connection to prevent water leaks and hose pull-off from vibration or pressure.

This clutch spring cap retains and protects the clutch spring in your washer's drive/clutch assembly, maintaining proper tension. Replacing a worn or missing cap helps the clutch engage smoothly and reduces slipping and noise during spin.

• Secures the clutch spring within the clutch assembly to prevent movement or dislodging
• Maintains correct spring preload for consistent clutch engagement
• Can help reduce clutch slip that appears as weak/no spin, slow spin ramp-up, or intermittent spinning
• Common signs of trouble: rattling or scraping near the drive, burning smell, or a visibly damaged/missing cap

• Unplug the appliance and shut off water before servicing
• Access the clutch per your model's service procedure; removing the gearcase/transmission and clutch may be required
• Carefully relieve spring tension and note the orientation of the spring and cap before removal
• Inspect the spring, clutch lining, and related hardware; replace any worn components during reassembly

This pressure switch is a factory-replacement control that senses air/pressure changes and helps the dryer run correct cycles and safety functions. It restores proper pressure detection so the dryer can heat and cycle as intended. What it does:

• Detects air/vacuum pressure changes to signal the dryer control for cycle and safety operations
• Helps ensure normal heating and timed cycles by allowing the control to confirm airflow/vent conditions
• Common symptom linkage: dryer won't heat, won't start, runs too long, or displays pressure/airflow-related fault codes
• Works with the dryer's vent/air sensing system

• One pressure switch

• Disconnect power before servicing to avoid shock or injury
• Inspect hoses and venting for blockages; replace damaged vacuum/air hose when installing this switch
• Handle connectors and terminals gently; ensure secure electrical connections and correct routing of pressure hose

Size: 10-24 x 3/8 inch.

Washer won't advance through cycles or stops after washing? This timer controls cycle selection and timing, restoring automatic cycle progression.

This siphon break kit prevents water from siphoning back out of the washing machine tub through the drain hose during the fill cycle. It acts as an air gap device installed on the drain line to ensure proper water levels are maintained. Replace this kit if your washer is not filling properly, takes too long to fill, or you notice water draining out as fast as it fills.

This screw-washer assembly secures panels, brackets, and other appliance components. The integrated washer spreads load and resists loosening, so replacing a worn or missing fastener restores a tight, reliable fit and helps eliminate rattles.

• Provides fastening with a built-in washer for even clamping and retention
• Replaces missing, stripped, or corroded hardware
• Helps address loose panels/handles and vibration or rattle noises
• Supports proper alignment of covers, brackets, and trim

• Disconnect power and shut off water or gas (as applicable) before servicing
• Match to the original fastener; location and quantity in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten; replace other severely rusted or damaged fasteners in the same area

Connects drain hose sections to prevent leaks and restore proper wastewater drainage. Replace if coupling cracks or connection leaks during draining.

Drain hose nozzle that attaches to the end of your washer's drain hose. Replace if cracked, broken, or missing to ensure proper hose connection.

Leaking water connection? This hose coupling creates a secure seal between your washer hose and water inlet, stopping drips and loose connections. DIY fix.

Outer tub assembly for your washer. Houses the inner basket and holds water during wash cycles. Replace if cracked, leaking, or damaged.

Wire connector block for washers. Transfers electrical connections between wiring harnesses. Replace if connector housing is cracked or melted.

Washer lid hinge attaches the lid to the cabinet, allowing smooth opening and closing. Replace if cracked, rusted, broken, or causing lid misalignment.