405Pnbm4h469 Parts

This replacement evaporator fan blade helps circulate cold air inside the freezer or refrigerator compartment to maintain even temperatures and proper cooling performance. A direct-fit replacement when the existing blade is cracked, warped, or missing. What it does:

• Moves air across the evaporator to promote even cooling and frost prevention
• Restores proper airflow when a damaged blade causes noise or reduced cooling
• Helps reduce hot or warm spots inside the compartment
• Quiet, balanced operation when installed correctly

• One replacement evaporator fan blade

• Disconnect power to the appliance before starting any repair
• Typically accessed by removing interior panels in the freezer/refrigerator compartment
• Inspect the fan motor shaft and mounting for damage before installing the new blade

The Right Door Closer is an OEM part for Frigidaire refrigerators. It is responsible for ensuring that the refrigerator door closes securely and maintains a proper seal, keeping the cold air inside and your food fresh.

A bad right door closer can be caused by wear and tear, damage, or misalignment. When the closer becomes faulty, it can result in issues such as a loose or sagging door, difficulty in closing the door properly, or a compromised seal that leads to temperature fluctuations.

Symptoms of a bad right door closer include:

• Door not closing or sealing properly
• Condensation or frost buildup inside the refrigerator
• Noisy or squeaking door operation

Replace your faulty right door closer with this genuine OEM part to restore your refrigerator door. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

There are multiple uses for the 5/16-18 Hex Screw. It is often used with small gasoline-powered yard equipment such as lawn and garden machines. While hex screws such as these may be used in edgers and snowblowers, the most frequent use this screw is in yard tractors. This variety of screw is commonly used in attaching the various appendages of gas-powered equipment to a central operating platform. In particular, these hex screws are used to secure the engine block of power tools to the frame or housing of the equipment. Once in place, these fasteners have an almost unbreakable strength to them. This is so much so the case that often, in order to detach the engine manifold and repair the inner workings of an engine, the bolts must be chiseled or cut loose. In such cases, it is necessary for the bolts to be replaced during reassembly. Manufacturers insist that genuine OEM replacement parts be used in the rebuilding process. These replacement parts were manufactured to the same exacting specifications used to make the original screws. These OEM screws are compatible with equipment made and sold by Yard-Man, Cub Cadet, Troy-Bilt, Husky, MTD, Bolens, and Yard Machines.

Hex washer head ,10-32 x 0.375. Ground

This solenoid is the electromagnetic actuator that moves or opens a valve or lever in compatible Frigidaire appliances, restoring correct mechanical action so the affected function operates reliably again. What it does:

• Converts electrical signals into mechanical movement to open/close a valve or actuate a latch
• Commonly controls water or ice fill, dispenser valves, or mechanical releases
• Replacing a failed solenoid can stop symptoms like no water/ice dispensing, valves not opening, or unresponsive mechanical actuators
• Designed to fit and perform like the original part when installed according to manufacturer instructions

• One solenoid

• Disconnect power (and water, if applicable) before starting any repair
• Inspect wiring and connectors for damage; test continuity with a meter

Replacement screw used to secure trim, brackets and panels on compatible Frigidaire appliances. Restores proper fit to reduce rattling and keep components from coming loose for safer, more reliable operation. What it does

• Secures panels, trim pieces and small brackets so parts stay aligned and flush.
• Stops rattling or vibration caused by missing or loose fasteners.
• Prevents components from shifting or falling out during normal use.
• Works wherever the OEM screw specified by the appliance diagram is required.

• Disconnect power (and water, if applicable) before starting any repair.
• Use the correct driver and size to avoid stripping the head or threads.
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic.
• If the new screw does not seat properly, confirm this is the correct OEM part before forcing it.

This is a replacement screw fastener used to secure panels, trim, or components on compatible Frigidaire appliances. It restores proper fit and prevents rattling or loose parts for safe, reliable operation. What it does:

• Secures panels, brackets, or trim pieces to keep components aligned and stable
• Prevents rattling, vibration noise, and gaps caused by missing or loose fasteners
• Restores proper assembly after service or part replacement
• Helps maintain safety by keeping covers and guards firmly attached

• One screw (single fastener)

• Disconnect power or unplug the appliance before servicing
• Use the appropriate driver to avoid stripping the head; do not overtighten
• Verify the screw matches the original in length and thread before installing

This cover is a replacement protective trim piece that shields internal components and restores the appliance's finished appearance. It helps keep parts protected from dirt while improving the unit's look. What it does

• Protects exposed components and wiring from dust and debris
• Restores damaged or missing exterior trim for a finished appearance
• Helps prevent accidental contact with internal parts
• Commonly replaced when cracked, broken, or missing

• One appliance cover as pictured and specified by the manufacturer

• Disconnect power to the appliance before starting any service
• Typically attaches with clips or screws; use appropriate tools and keep fasteners
• Handle carefully to avoid scratching the replacement part

This replacement coil-cover gasket seals the refrigerator coil/cover area to help maintain proper airflow and reduce dust buildup around the condenser/evaporator cover. Restores the intended fit and helps maintain cooling efficiency. What it does:

• Seals the gap between the coil cover and cabinet to direct airflow over coils
• Helps prevent dust, debris and pet hair from collecting on coils
• Reduces vibration noise by cushioning the cover edge
• Commonly replaced when the gasket is torn, flattened, or missing, or when air leaks are noticed

• Inspect mating surfaces and remove old adhesive/residue before installing for a secure seal
• Use appropriate adhesive or clips if required by your model; follow OEM instructions
• Disconnect power to the appliance before servicing and avoid sharp edges on sheet metal

This mounting bracket secures appliance components to the cabinet frame, restoring solid support and alignment. It's a straightforward replacement for worn, bent, or broken brackets that cause loose panels or misaligned doors. What it does:

• Provides structural support for interior or exterior panels and components
• Helps stop rattling or vibration caused by a loose or damaged bracket
• Restores proper alignment to doors or trim that shift due to bracket failure
• Used wherever a small metal bracket fastens parts to the appliance frame

• One mounting bracket

• Disconnect power to the appliance before servicing to avoid shock or injury
• Installation typically requires basic hand tools; keep fasteners for reuse unless replacement specified
• Handle edges and metal parts carefully to avoid cuts; consider gloves

This is a replacement outer housing cover that restores the appliance's exterior protection and appearance. It shields internal components from debris and helps maintain a finished look for the unit. What it does:

• Covers and protects internal components from dust, dirt and incidental contact
• Restores a clean, finished exterior where the original cover was cracked, warped or missing
• Helps prevent small objects from falling into internal openings
• Reduces visible wear on the appliance for a neater installation

• Disconnect power to the appliance before starting any work
• Remove any retaining screws or clips holding the old cover in place; lift or slide out gently
• Align the replacement cover carefully and re-secure with original hardware

This light assembly restores interior illumination so you can see food and controls clearly. It replaces a broken, cracked, or non-working refrigerator interior light housing for reliable, even lighting inside the compartment. What it does:

• Provides interior illumination for refrigerator compartments.
• Replaces cracked or yellowed lens, damaged housing, or failed light socket.
• Fixes intermittent or non-working interior lights caused by a faulty assembly.
• Helps bulbs seat correctly and stay connected to the refrigerator wiring.

• Disconnect power to the refrigerator (unplug or shut off circuit) before installation.
• Handle the lens carefully to avoid scratching or cracking; bulbs may need replacing separately.
• Verify connector orientation and secure wiring harness to prevent loose connections.

This replacement drawer panel restores the front face of an inner refrigerator drawer so it looks and functions like new. It provides the finished surface users see and helps keep stored items contained. What it does:

• Replaces a cracked, faded, or damaged inner drawer front to improve appearance
• Restores a secure front edge so the drawer opens and closes properly
• Prevents gaps that can let items shift or become trapped under the drawer
• Matches the OEM fit and mounting points for a direct swap

• Unplug the appliance or disconnect power before working on the refrigerator.
• Remove the drawer per your model's service instructions to access mounting clips or screws.
• Handle the panel carefully to avoid scratching; align mounting tabs before pressing or fastening.
• If you encounter broken clips or fasteners, replace them with the correct parts rather than forcing the panel.

This is a replacement mounting nut used to secure components on compatible Frigidaire appliances. It provides a simple, reliable fastener to replace a missing, damaged, or corroded nut and restore proper part retention. What it does

• Secures panels, brackets, or hardware so parts stay in position during use
• Replaces stripped, rusted, or missing nuts that cause rattling or loose components
• Helps restore proper alignment and safe operation of the affected assembly
• Small fastener used wherever the OEM diagram specifies part 561231207

• One mounting nut (part number 561231207)

• Disconnect power or unplug the appliance before starting any repair
• Use the correct-size wrench or socket to avoid rounding the nut
• Tighten snugly but do not overtighten to prevent thread damage
• If the original nut was corroded, inspect mating threads and replace the bolt/stud if needed

This is a self-tapping screw that can be used on a wide variety of lawn and garden equipment in many applications. A self-tapping screw is used to secure metal, wood, plastic, and brick together. When using a self-tapping screw, there's no need to drill a pilot hole since the screw makes its own hole. The only exception is with metal, which will still need a drilled hole before installation. There are many situations when a screw may need to be replaced. Some screws are damaged or broken, while others can become loose and no longer hold materials together. Screw heads can become stripped, which will also mean they need to be replaced. A visual inspection can often give an indication of whether you should replace a self-tapping screw. This is a genuine OEM hex head screw that can be used on various lawn and garden equipment, including wood chippers, lawn mowers, snowblowers, log splitters, tillers, edgers, and leaf blowers. It's compatible with products by MasterCut, Craftsman, Turf King, Cub Cadet, Yard-Man, Ryobi, Bolens, Troy-Bilt, Montgomery Wards, Murray, Huskee, Yard Machines, MTD, and more. This screw is sold individually.