4Ksmc50s Parts

Replacement 5-quart polished stainless steel mixing bowl with comfort handle for tilt-head stand mixers. Needed when original bowl is cracked or worn.

If your mixer makes excessive noise or vibrates during operation, a worn spring seat cap may be the cause. This part centers and secures springs for smooth, quiet performance.

Fix a stand mixer that won't turn beaters or rotates unevenly. This planetary pinion gear restores smooth rotation when teeth are worn or stripped.

This genuine replacement gear is a drivetrain component that transfers motor rotation to a mating mechanism inside your appliance. Replacing a worn or stripped gear restores smooth, reliable motion and helps prevent damage to adjacent parts.

• Meshes with adjacent gear(s) or a shaft to drive an internal mechanism
• Worn or rounded teeth can cause slipping, skipping, or no movement
• Intermittent or stalled movement can indicate a stripped or damaged gear

• Disconnect power (and shut off water/gas if applicable) before servicing
• Access the assembly; note orientation and timing marks
• Transfer any spacers, keys, or retaining clips from the old gear
• Seat the new gear fully and verify smooth manual rotation before restoring power

If your stand mixer runs only on high speed or won't change speeds properly, a worn governor drive stud may be the cause. This small repair restores smooth speed control in about 30 minutes.

Rubber foot for stand mixer base. Replaces worn, cracked, or missing feet. Stabilizes mixer, reduces vibration, and protects countertops.

This cap spring is a small coil that supplies the return tension a cap or button needs to operate smoothly. Replace it if weakened, bent, or missing to restore proper feel and reliable engagement of the mechanism.

• Maintains spring tension under a cap/button to keep parts aligned
• Helps the cap return smoothly and prevents looseness or rattling
• Supports consistent engagement of the related control or latch
• Typical signs of fatigue: loose or wobbly cap, sticking action, poor return, or a spring that pops out

• Disconnect power and shut off water/gas supplies before servicing
• Note the spring's orientation and stack-up; take photos as you disassemble
• Use needle-nose pliers and control the spring so it doesn't eject
• Seat components fully and test operation before final reassembly

White plastic back cover for stand mixers. Protects internal components at rear of motor housing. Replace if cracked, broken, or missing.

If your stand mixer bowl lift won't stay up or slips out of position, this spring roll pin secures the lift arm linkage. Requires pin punch to install.

This bearing supports a rotating shaft or assembly inside the appliance, reducing friction for smooth, quiet operation. Replacing a worn bearing restores proper alignment and helps prevent noise and premature wear on connected parts.

• Provides a low-friction surface for smooth rotation
• Helps keep the rotating component centered and stable
• Reduces vibration and operating noise
• Common failure signs: grinding/squealing, wobble or play, rough or intermittent rotation

• Disconnect power; also shut off water or gas supply if applicable
• Access the assembly per your model's service information and note part orientation before removal
• Inspect the shaft/hub and any spacers or seals for wear; replace related worn components
• Seat the bearing squarely—do not force; apply only manufacturer-specified lubricant if called for in service literature

This 8-32 x 5/8 screw replaces missing or damaged hardware specified by the manufacturer to secure panels, brackets, and internal components in your appliance. Restores a tight, rattle-free fit to help prevent vibration and misalignment.

• Provides the correct 8-32 thread and 5/8-inch length where specified
• Secures sheet-metal panels, brackets, and internal assemblies
• Replaces missing, stripped, or corroded screws
• Symptoms include loose or rattling panels, misaligned parts, or hardware that won't stay tight

• Disconnect power; shut off gas before servicing
• Support panels/components while removing or installing hardware
• Start threads by hand to avoid cross-threading; tighten only until snug
• Match the original screw's location and orientation for proper fit

Replace your mixer's wavy spring washer to reduce vibration and noise. This washer maintains proper tension between shaft components for smoother operation.

This headless, cup-point set screw secures a component to a shaft or hub inside your appliance. The 1/4-28 x 3/8 in size bites into the mating surface to prevent slipping, helping keep collars, pulleys, or knobs aligned and stable.

• Locks a hub, collar, or pulley to a shaft to prevent movement
• Helps maintain alignment and reduce wobble or vibration
• Replaces missing, stripped, or damaged set screws
• Common signs include components slipping on a shaft, rattling noises, or recurring loosening

• Disconnect power before servicing
• Clean threads and align with any flat on the shaft before tightening
• Start threads by hand to avoid cross-threading; tighten securely without overtightening
• Recheck tightness after a brief test run

Replacement thread ring for 5-quart glass bowls on stand mixers. Secures the bowl to the mixer base. Replace if cracked, broken, or worn threads.

Fix a mixing bowl that won't lock in place or keeps sliding during use. This retaining pin secures the bowl clip to keep your bowl firmly seated.

Fix intermittent mixer operation or arcing sounds with this brush holder housing. Secures carbon brushes for steady motor contact and consistent speed.