Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This genuine OEM replacement part is a pulley assembly for dryers. Sometimes called an idler arm, the pulley assembly keeps the dryer drive belt under tension as the belt wraps around the dryer drum. If the dryer is no longer spinning properly and is making a lot of noise, the pulley assembly may need to be replaced. Luckily this repair is a relatively simple process.To remove the old dryer pulley assembly, start by making sure the dryer is unplugged. Remove the lint screen from the top of the dryer. Remove the two Phillips screws by the lint screen opening. Depress the clips that hold the top cover down. Lift the top cover and keep it in an upright position. Disconnect the wire harness to the switch that separates the connector. Remove the screws on the front panel. Lift the panel forward and set it to the side. Next, lift the drum and locate the pulley assembly under the drum. Lift the belt off the motor pulley to remove the assembly. Set the new pulley assembly in the same position as the old one and make sure everything is aligned. Rotate the drum to make sure it rotates smoothly. reinstall the panels.This replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador dryers.
Usually ships within 4 - 14 days
Spiral pin secures the roller axle in your dishwasher's lower rack assembly. Replace if the pin is missing, bent, or dislodged to restore stability.
Detergent cup cam for dishwashers. Installs inside the detergent dispenser to control cup opening. Replace if cam is cracked, broken, or worn out.
I knew the detergent dispenser was broken. That was an easy fix - though I did find that the retaining pin was too big, and I had to make the hole in the shaft a little bigger. As far as the noise, I started disassembling and cleaning things, until I found that the diverter had broken free from the top of the housing, and was now stuck on the motor. I could see marks from where the diverter had been grinding away the housing. I was worried about prying on the motor (the diverter was very... Read more
Mounting screw for dishwasher assembly. Secures internal components and panels. Replace if stripped, corroded, missing, or damaged during repairs.
Engine won't restart after hitting an object? A sheared flywheel key is often the cause. This small part keeps the flywheel connected to the crankshaft.
This is a flexible drain hose used in certain cooking appliances to route water or condensation away from the unit. It connects between the internal drain outlet and the external drain point. Replace this hose if you notice leaking, cracking, kinking, or if water is not draining properly from the appliance.
Replace your dishwasher door gasket when you notice water leaks, visible wear, or poor sealing. Maintains a watertight seal for efficient operation.
Replacement screw for dishwasher assembly and mounting. Used to secure components throughout your dishwasher. Replace if stripped, missing, or damaged.
Replaced Read more
Seals the connection between your dishwasher pump and housing to prevent leaks. Replace when you notice water pooling or dripping. Confirm fit with your model.
I ordered the parts and called a tech who talked my husband thru installing both gaskets. She was very helpful. Read more
Replace the spray tower tip in your dishwasher if it's cracked, broken, or missing. This component caps the top of the spray tower assembly.
Dishwasher rack bushing that mounts on the dish rack assembly. Replace this bushing if it's cracked, broken, worn, or missing to restore smooth rack movement.
Replaces cracked or broken dishwasher spray arm water distributor. Essential component that directs water flow through the spray arm assembly.
Seals the filter housing assembly to prevent leaks in your dishwasher. Replace if cracked, worn, or causing water leakage during cycles.
I took the pump apart to exam, checked drain hose and sink drain first, everything looked OK. After studying the problem for a while I decided it had to be in the filter, ordered a new filter and it took about 10 minutes to replace. After getting the new filter I realized that there was a check ball rattling inside the new one that my old filter did not have anymore, the real cause for the pump not to drain. P.S. I ordered these parts from Sears because they said that they had everything in... Read more
O-ring seal for dishwashers prevents leaks at pump and filter connections. Replace when cracked, brittle, or leaking. Confirm fit with model number.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.