66515X55790 Parts

This left-hand door hinge supports and pivots the door so it opens smoothly and closes tight. Replace a worn hinge to correct sagging, rubbing, or doors that won't seal—improving performance and preventing damage. What it does:

• Provides the pivot point for the door on the left side
• Maintains alignment so the door sits level and latches/seals properly
• Helps the door open and close smoothly without binding
• Common symptoms: door sags or rubs, won't close fully, uneven gaps, squeaking/grinding noises, poor seal

• One left-hand door hinge

• Disconnect power; also shut off gas and/or water before servicing
• Support or remove the door before unfastening the hinge; some hinges may be under spring tension—use caution
• Transfer original hardware/shims as needed and tighten fasteners securely
• Check door alignment and gasket contact after installation; open/close several times to ensure smooth operation

• "Left-hand" is determined when facing the front of the appliance.

Right-hand door hinge that replaces a worn or damaged refrigerator door hinge to restore proper door alignment and smooth opening and closing. Helps maintain a tight seal and prevents door sag or binding. What it does:

• Supports and pivots the refrigerator door on the right-hand side for correct alignment.
• Restores smooth opening/closing and reduces rubbing or scraping at the cabinet.
• Helps re-establish a full door seal to prevent cold air loss and temperature issues.
• Addresses symptoms such as a sagging or misaligned door, noisy hinge movement, or a door that doesn't close evenly.

• Disconnect power to the appliance and remove any items from the door before starting.
• Support the door while removing hinge hardware to prevent sudden drops or damage.
• Reuse existing screws/hardware unless replacement hardware is provided; tighten securely but avoid over-torquing.
• After installation, check door alignment and gasket contact; adjust hinge position as needed to ensure proper sealing.

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

This support bracket helps hold internal components in place to restore proper alignment and reduce movement. It's a simple replacement that stabilizes the affected assembly and helps stop rattling or sagging. What it does:

• Secures and supports a loose or misaligned internal component or panel
• Prevents shifting that can cause vibration, noise, or uneven operation
• Restores proper alignment to reduce wear on adjoining parts
• Functions as the OEM replacement for the original support bracket

• One support bracket

• Inspect the mounting points and surrounding parts for wear before installing
• Replace only with the matching OEM part number to ensure fit; fasten securely per manufacturer torque recommendations
• Disconnect power and follow basic safety precautions before servicing the appliance

The Wire Harness is an OEM component specifically designed for Whirlpool dishwasher models. Found running across the inner tub cavity and control compartments, the wire harness routes electrical connections between the control panel, pump, heater element, and other critical components. 

Composed of flame-retardant plenum-rated cabling with silicon jacket coating, the harness features carefully positioned bundles routed through grommet-sealed anchors. Precise terminal connections deliver consistent voltage levels to components. 

Causes of a bad wire harness include degraded insulation from prolonged high-temperature and moisture exposure and weakening internal cabling. Cracks or abrasions exposing vulnerable wiring over time are also possible causes.

Symptoms of a bad wire harness include:  

• Faulty or non-responsive controls
• Unexpected error codes 
• Intermittent component operation

Compatible with additional dishwasher brands including KitchenAid, Jenn-Air, and select Kenmore models.

This access panel provides a fitted cover that protects internal components while allowing service access when removed. It restores the appliance's exterior appearance and keeps wiring and parts safely enclosed. What it does:

• Covers and protects controls, wiring, and service areas from dust and accidental contact
• Provides removable access for diagnostics and repairs without damaging surrounding trim
• Helps maintain proper airflow and finish around the service area
• Reduces visible gaps and improves the appliance's exterior look

• Disconnect power to the appliance before removing or installing the panel
• Use the original screws or mounting hardware to secure the panel; do not force or bend metal
• Handle edges carefully to avoid cuts; wear gloves if needed

This Tube-Feed supplies water to the appliance's ice/water system, restoring proper water flow to the ice maker or dispenser. A direct-fit replacement that helps stop reduced ice production or interrupted water delivery. What it does:

• Routes incoming water from the inlet to the ice maker or dispenser assembly
• Restores proper water flow when the original tube is cracked, kinked, or clogged
• Helps stop leaks or puddling caused by damaged tubing when installed correctly
• Works with the appliance's original fittings and seals to maintain a secure connection

• One Tube-Feed

• Disconnect power and shut off the water supply before starting any repair
• Inspect fittings and seals; replace any damaged clamps or gaskets for a watertight connection
• Avoid sharp bends or kinks when routing the tube; secure with existing clips
• Turn water back on and check all connections carefully for leaks before restoring power

This console assembly is the outer control panel housing that holds and protects the appliance's control buttons, touchpad, and display—restoring a secure, finished surface for normal operation and user access. What it does

• Replaces a cracked, broken, or warped control-panel housing that exposes internal controls
• Provides a stable mounting surface for buttons, knobs, and the control PCB
• Helps prevent moisture, debris, and accidental impact from reaching electronics
• Restores a clean, factory-style appearance for user interface and display
• Can resolve issues where controls are loose, misaligned, or difficult to operate

• One console assembly (housing) as shown

• Always unplug the appliance or shut off its circuit breaker before starting work
• Some disassembly of trim, bezels, or retainers may be required; keep fasteners organized
• Handle the display and control components carefully when transferring them to the new console

This is an electrical wire-harness connector used to join wiring in the appliance. It restores a secure electrical connection so controls and components receive proper power and signaling. What it does:

• Provides a secure mating point between wiring harnesses or between a harness and a component
• Maintains proper electrical contact to prevent intermittent power or signal loss
• Commonly used where a detachable electrical connection is needed for service or assembly
• Can help address symptoms like intermittent operation, components not powering on, or visible damaged/loose plug ends

• Disconnect power to the appliance before inspecting or replacing any electrical connector
• Verify connector orientation and full engagement; bent terminals may need replacement
• Compare the replacement to the original to ensure terminal count, shape and locking feature match
• If wiring insulation or terminals are damaged, replace the harness

This clamp secures flexible appliance hoses and helps prevent leaks by keeping hose connections tight. A simple replacement that restores a secure seal at water or drain hose joints. What it does

• Tightens around a hose to hold it firmly on a fitting or barb
• Helps stop water leaks from loose or worn hose connections
• Used where a small, durable clamp is required on water or drain lines
• Common repair for loose hoses after maintenance or aged clamps

• One clamp

• Turn off water and power to the appliance before inspecting or replacing hoses
• Slide clamp onto hose, seat hose fully on the fitting, then position and compress or tighten clamp as designed
• Replace any hose showing cracks or wear rather than just re-clamping
• Wear eye protection when compressing or cutting metal clamps

This lid is the washer's top cover that protects internal components and keeps clothes contained during operation. It restores the washer's enclosure and helps maintain safe, splash-free cycles. What it does:

• Covers the washer tub and control area to prevent splashes and keep items inside during cycles
• Provides the surface that the lid latch/switch engages to enable normal operation
• Replaces cracked, warped, or missing lids that allow debris in or interfere with closing
• Helps maintain the appliance's appearance and proper function of the top access

• Disconnect power before starting any repair to avoid electrical hazard
• Lift off or unbolt existing lid per your model's service instructions; alignment may be required for proper closure
• Keep screws and small parts organized; some models use hinge pins or clips that must be reinstalled
• If your washer also has a separate lid latch or switch, inspect and replace it only if listed as defective

This insulated wire lead carries electrical current between components, restoring reliable power routing in your appliance. It's a direct-replacement discrete wire used where a single conductor is required for safe operation. What it does:

• Provides a single insulated conductor to connect terminals or components
• Restores proper electrical continuity when a wire is damaged, burned, or disconnected
• Helps prevent shorts by maintaining insulation between conductors
• Suitable for low- to moderate-current wiring routes within the appliance

• One insulated wire lead as shown

• Disconnect power before inspecting or replacing wiring to avoid shock or injury
• Route the wire as the original, avoiding sharp edges and heat sources; secure with existing clips or ties
• Replace any damaged terminals, connectors, or fasteners; use correct crimps or solder joints per OEM practice