722T1bc Parts

Replace broken or missing tines in your dishwasher's dish rack. This component supports and secures dishes during wash cycles. Easy replacement part.

Mounts over the dishwasher's drying fan vent opening to shield the blower and direct airflow into the tub. Replace if cracked, damaged, or missing.

Color: blue. It measures about 3 inches wide by 1 inch high.

This safety interlock switch assembly controls the microwave's door-sensing circuit, allowing the oven to run only when the door is fully latched. Replacing a worn assembly restores safe, consistent start/stop behavior. What it does:

• Detects door open/closed status and completes the safety interlock circuit
• Prevents operation with the door open; allows cooking only when latches engage
• Helps address: won't start unless pressing on the door, shuts off when the door is jostled, "Door"/"Open/Close" error
• Also corrects interior light or fan staying on/off incorrectly due to a failed interlock switch

• One safety switch assembly

• Disconnect power; microwaves contain a high-voltage capacitor that can retain a dangerous charge even unplugged
• Remove the outer cabinet to access the door-latch/interlock area
• Note switch orientation and wire locations; transfer connectors one at a time and secure the assembly
• After reassembly, confirm smooth door closure and test for proper start/stop operation

Fix unresponsive buttons, error codes, or cycles that won't start. This main control board coordinates all dishwasher functions. Moderate DIY repair.

The Pump and Case Assembly is an OEM component specifically designed for LG dishwashers. It contains the circulating pump that recirculates wash water, drainage and filtration functions.

Causes of failure usually stem from normal wear of seals and internal components handling heated soapy water daily. Impeller parts may corrode or weakened gaskets crack.

Symptoms of a bad pump assembly include:

• Puddles underneath or inside the dishwasher
• Error codes related to draining or water detection 
• Dirty dishes despite running full cycles

This OEM part also fits select Sears/Kenmore models.

The Pump Motor Assembly is an OEM component specifically designed for LG dishwashers. It houses both the wash and drain pump motors integrated within a singular assembly. 

These motors work together to efficiently circulate water through spray arms during wash cycles for optimized cleaning performance. They also help drain dirty water at the end of each cycle, ensuring dishes are thoroughly rinsed.  

Symptoms of a bad pump motor assembly include:

• Inadequate or incomplete wash and rinse performances
• Water failing to drain fully after cycles
• Leaks occurring due to ineffective pumps   
• Abnormal sounds from the motor during the operation

Causes can include normal wear over time, failures in motor electronic components, or damage from foreign debris. 

Replacing the pump motor assembly with this genuine OEM LG part restores optimized wash and rinse functions. It is also compatible with Sears/Kenmore dishwashers.

Oven won't light even though igniter glows? Burner lights only when valve is tapped? Replace the dual gas safety valve. DIY install in under 1 hour.

Replacement power cord for ovens and ranges. Installs at the rear panel to restore electrical connection. Needed when original cord is frayed or damaged.

The Leg is an OEM part for LG dishwashers. It serves as a critical base component that elevates the dishwasher body above the floor for proper drainage. Legs are constructed with durable corrosion-resistant materials and adjustable height features to accommodate most flooring types. 

Symptoms of a bad leg can include:

• The dishwasher wobbles or is uneven during operation
• Standing water or improper draining of wash water  
• Visible damage like cracks, bending, or rust affecting stability

Causes of leg failure typically arise from normal wear over extended use of hard flooring. Replacing deteriorated legs restores the appliance's security and balance for optimum performance.

This affordable OEM LG part ensures the dishwasher stays firmly in place during cycles while conveniently adjusting to most installation situations. It provides customers with many more trouble-free years of use. This replacement leg is also compatible with KitchenAid models.

This door boot gasket seals the opening between the door and tub on front-load washers, keeping wash water contained. Replacing a worn boot restores a tight seal to prevent leaks and ensure proper door closure.

• Creates a watertight seal between the washer door and front tub
• Helps prevent leaks, drips, and moisture at the front of the machine
• Common signs of failure: visible tears/cracks, persistent mildew, clothes snagging, or the door not sealing flush
• Restores correct door sealing to maintain efficient wash performance

• Unplug the washer and turn off water supplies before servicing
• Remove the outer and inner spring/clamp rings; note orientation of the gasket and drain port
• Lightly soap the lip to ease installation and align the drain/weep holes at the 6 o'clock position
• Reinstall clamps securely and run a short cycle to check for leaks

Check valve that prevents water backflow in the appliance's supply line, helping restore proper water flow to the ice maker or dispenser. Replaces a failed valve to address leaking, slow fills, or no-fill conditions. What it does:

• Stops reverse flow in the water line so water only moves toward the dispenser or ice maker
• Helps prevent water leaks and cross-contamination of the supply line
• Common symptom fixes: intermittent or no water to ice maker/dispenser, weak fills, or water pooling
• Fits inline with existing water tubing and works with the appliance's fill system

• Shut off water supply and unplug the appliance before replacing the valve
• Confirm tubing size and orientation before installation; install with correct flow direction
• Tighten fittings to prevent leaks but avoid overtightening plastic fittings

This refrigerator damper assembly opens and closes the air passage between the freezer and fresh food sections. Replacing a sticking or broken damper restores proper airflow and more stable temperatures, helping resolve warm spots or food freezing in the refrigerator.

• Regulates cold-air flow from the freezer into the refrigerator to maintain set temperatures
• Operates a flap within the air duct under control of the appliance's control system
• Helps reduce temperature fluctuations and improve overall cooling performance

• Disconnect power before servicing
• Access from inside the fresh food compartment; remove shelves and the damper/duct cover
• Remove mounting screws and disconnect the wire harness; transfer any foam seals or clips from the old unit if needed
• Seat the gasket evenly to prevent air leaks and route wiring away from the moving flap

This inlet hose supplies water from your home plumbing to the appliance's water inlet connection, ensuring a reliable flow during operation and helping prevent leaks when properly secured.

• Carries incoming water from the household supply to the unit's inlet valve/port
• Helps resolve issues like no fill, slow fill, or intermittent fill
• Restores proper water supply when the original hose is cracked, kinked, or damaged

• Unplug the appliance and shut off the water supply before servicing
• Keep a towel or container handy to catch residual water
• Hand-thread fittings first to avoid cross-threading, then tighten securely without overtightening
• After installation, turn water on and check all connections for leaks

This locker lock is the replacement latch mechanism that secures the appliance door during operation, restoring proper door closure and helping the unit run safely and reliably. Use when a door won't stay closed or the machine won't start. What it does:

• Replaces a worn or broken door latch to restore secure door closure
• Helps ensure the appliance detects a closed door and can start cycles
• Commonly used when the door is loose, won't latch, or causes door-sensor errors
• Fits into the door strike area and engages the cabinet catch for a firm hold

• Locker lock (single replacement latch)

• Disconnect power and water supply before servicing to avoid shock or injury
• Remove the outer door panel or access cover as needed to reach the latch area
• Verify alignment of the latch and striker when reinstalling to ensure proper engagement

Replace broken or missing tines in your dishwasher's dish rack. This prong holds and spaces dishes securely during wash cycles. Ideal for cracked tines.