722T1bc Parts

This gasket creates a watertight seal at its designated connection point in the dishwasher, helping keep wash water contained throughout the cycle. Replacing a worn seal helps stop nuisance leaks and protects nearby cabinetry and floors. What it does:

• Forms a tight, leak-resistant seal between mating dishwasher components
• Helps keep wash water inside the tub to maintain proper cleaning performance
• Wear, flattening, or tears can allow drips or pooling during/after cycles
• Common clues: visible damage, moisture at the mounting area, or water on the floor near the unit

• 1 gasket

• Disconnect power and turn off the water supply before servicing
• Access the gasket location per your model's service information; note the old seal's orientation
• Clean the channel/mating surfaces; seat the new gasket evenly without stretching or twisting
• Reassemble and run a short test cycle to check for leaks

This dishwasher sensor assembly is the turbidity (soil) sensor that monitors wash-water clarity and reports to the control. Replacing a failing sensor restores proper cycle timing and consistent cleaning performance.

• Measures the cloudiness/soil level of the wash water during cycles
• Sends feedback to the control to optimize wash, rinse, and cycle length
• Helps maintain cleaning performance and efficiency
• Failure symptoms include unusually long or short cycles, poor cleaning, or cycles that won't complete

• Disconnect power and shut off water before servicing
• Access the sensor at the sump; release the lock and twist to remove (some residual water may drain)
• Inspect/transfer the seal; seat the new sensor fully and lock in place to prevent leaks
• Reconnect wiring, restore power/water, and run a test cycle to check for leaks and proper operation

Check valve that prevents water backflow in the appliance's supply line, helping restore proper water flow to the ice maker or dispenser. Replaces a failed valve to address leaking, slow fills, or no-fill conditions. What it does:

• Stops reverse flow in the water line so water only moves toward the dispenser or ice maker
• Helps prevent water leaks and cross-contamination of the supply line
• Common symptom fixes: intermittent or no water to ice maker/dispenser, weak fills, or water pooling
• Fits inline with existing water tubing and works with the appliance's fill system

• Shut off water supply and unplug the appliance before replacing the valve
• Confirm tubing size and orientation before installation; install with correct flow direction
• Tighten fittings to prevent leaks but avoid overtightening plastic fittings

The Leg is an OEM part for LG dishwashers. It serves as a critical base component that elevates the dishwasher body above the floor for proper drainage. Legs are constructed with durable corrosion-resistant materials and adjustable height features to accommodate most flooring types. 

Symptoms of a bad leg can include:

• The dishwasher wobbles or is uneven during operation
• Standing water or improper draining of wash water  
• Visible damage like cracks, bending, or rust affecting stability

Causes of leg failure typically arise from normal wear over extended use of hard flooring. Replacing deteriorated legs restores the appliance's security and balance for optimum performance.

This affordable OEM LG part ensures the dishwasher stays firmly in place during cycles while conveniently adjusting to most installation situations. It provides customers with many more trouble-free years of use. This replacement leg is also compatible with KitchenAid models.

This replacement clip secures components within your appliance. Replacing a broken, bent, or missing clip restores a firm hold on panels or assemblies to prevent shifting and reduce vibration noise.

• Holds specified parts or panels in place where a clip is called out in the assembly
• Helps maintain proper alignment and minimizes rattles/vibration
• Direct replacement for a damaged or missing clip
• Common symptoms: loose or misaligned parts, rattling during operation, clip visibly broken or missing

• Disconnect power before service; also shut off gas/water supplies
• Note the original clip orientation and placement; take a photo for reference
• Use needle-nose pliers for removal/installation; avoid overbending or deforming the clip
• Inspect mating parts for wear or damage and ensure the clip seats fully

This door boot gasket seals the opening between the door and tub on front-load washers, keeping wash water contained. Replacing a worn boot restores a tight seal to prevent leaks and ensure proper door closure.

• Creates a watertight seal between the washer door and front tub
• Helps prevent leaks, drips, and moisture at the front of the machine
• Common signs of failure: visible tears/cracks, persistent mildew, clothes snagging, or the door not sealing flush
• Restores correct door sealing to maintain efficient wash performance

• Unplug the washer and turn off water supplies before servicing
• Remove the outer and inner spring/clamp rings; note orientation of the gasket and drain port
• Lightly soap the lip to ease installation and align the drain/weep holes at the 6 o'clock position
• Reinstall clamps securely and run a short cycle to check for leaks

This inlet hose supplies water from your home plumbing to the appliance's water inlet connection, ensuring a reliable flow during operation and helping prevent leaks when properly secured.

• Carries incoming water from the household supply to the unit's inlet valve/port
• Helps resolve issues like no fill, slow fill, or intermittent fill
• Restores proper water supply when the original hose is cracked, kinked, or damaged

• Unplug the appliance and shut off the water supply before servicing
• Keep a towel or container handy to catch residual water
• Hand-thread fittings first to avoid cross-threading, then tighten securely without overtightening
• After installation, turn water on and check all connections for leaks

Replacement wire rack that provides secure support for dishes, cookware, or food inside the appliance, restoring proper spacing and helping prevent items from tipping or sliding. What it does:

• Supports dishes, pans, or food to keep items stable during use.
• Restores proper spacing to improve loading and prevent overcrowding.
• Replaces bent, rusted, or missing racks that cause items to sit unevenly.
• Helps prevent items from shifting and potentially contacting interior surfaces.

• Disconnect power or unplug the appliance before attempting installation.
• Ensure the rack is oriented correctly and that any rollers or clips engage smoothly with the track.
• Do not force the rack into place; inspect mounting clips or rollers for damage and replace if worn.
• Wear gloves to avoid sharp edges; replace rather than repair if the rack is rusted or severely bent.

This is a common fastening nut used to secure panels, trim, or components on compatible LG appliances. It provides a simple, reliable way to hold mating parts in place and restore proper fit and function. What it does

• Secures panels, brackets, or hardware to prevent movement or vibration
• Stops rattling or loose parts caused by a missing or worn nut
• Restores proper alignment when replacing damaged or stripped fasteners
• Works where a standard threaded nut is required for reassembly

• One common nut as pictured

• Disconnect power and water before servicing the appliance
• Use the properly sized wrench or socket to avoid rounding the nut
• Do not overtighten; tighten until snug and secure per OEM torque guidance
• Replace like-for-like—thread size and type match the original

Replacement oven door seal that creates a heat-tight barrier around the oven door to help maintain oven temperature and reduce heat loss. Restores proper door sealing for more even cooking and safer operation. What it does:

• Seals the oven cavity to retain heat and stabilize cooking temperature.
• Helps prevent heat, smoke and odors from escaping the oven during use.
• Replace when the gasket is cracked, flattened, torn, brittle or the oven takes noticeably longer to preheat.
• Improves door closure and can reduce energy loss when installed correctly.

• Disconnect power (and gas if applicable) and allow the oven to fully cool before starting.
• Remove the old gasket per the oven's service instructions; some models require removing the door or loosening fasteners.
• Press the new gasket into the door channel evenly, working around the perimeter so the seal seats flush.
• Wear gloves to protect hands from sharp edges.

This parts assembly is a pre-packaged set of components used to replace a worn or damaged group of parts in one area of the appliance. Installing the matched assembly helps restore proper fit and reliable operation.

• Replaces multiple small components as a single matched set
• Restores alignment and function in the related mechanism
• Can help with looseness, rattling, poor fit, or intermittent operation
• Built to match original form and connection points for correct fit

• Disconnect power and shut off water or gas before servicing
• Use your model's exploded view/service manual to locate and orient
• Keep track of screws, spacers, and clips; transfer any reusable hardware
• Verify smooth operation before restoring power and normal use

This is the appliance's user-interface control panel assembly. It houses the buttons/keys and display area used to select settings and cycles, restoring clean looks and responsive controls when the original panel is damaged or the keys stop working.

• Provides the button/keypad interface for operating the unit
• Routes user input to the main control board via the harness/ribbon
• Supports and protects the front user-interface area
• Common symptoms: unresponsive or intermittent buttons, stuck keys, cracked/broken panel, worn or peeling overlay graphics

• Disconnect power before servicing
• Remove trim/screws to access the panel; note fastener locations
• Carefully release clips and unplug the ribbon/harness; avoid creasing flex cables
• Transfer any reusable components from the original panel as needed; test functions before final reassembly

This locker lock is the replacement latch mechanism that secures the appliance door during operation, restoring proper door closure and helping the unit run safely and reliably. Use when a door won't stay closed or the machine won't start. What it does:

• Replaces a worn or broken door latch to restore secure door closure
• Helps ensure the appliance detects a closed door and can start cycles
• Commonly used when the door is loose, won't latch, or causes door-sensor errors
• Fits into the door strike area and engages the cabinet catch for a firm hold

• Locker lock (single replacement latch)

• Disconnect power and water supply before servicing to avoid shock or injury
• Remove the outer door panel or access cover as needed to reach the latch area
• Verify alignment of the latch and striker when reinstalling to ensure proper engagement

This clamp secures hoses or wiring to the appliance chassis to prevent movement, chafing, and vibration-related wear. It helps keep connections stable so hoses and wires stay in place during normal use. What it does:

• Holds water, drain or vent hoses in position to reduce strain and prevent rubbing
• Keeps wiring harnesses routed and fastened to avoid chafing or accidental disconnection
• Reduces vibration-related noise caused by loose hoses or wires
• Helps prevent hose kinks and unintended movement that can lead to leaks or intermittent electrical issues

• One clamp

• Disconnect power to the appliance before servicing; shut off water supply if working with water lines
• Remove panels as needed to access the hose or wiring route, then replace the clamp in the same orientation
• Use appropriate pliers or a screwdriver if required; do not overtighten or deform the hose or wiring
• If the original clamp was secured with a fastener, retain and reuse it only if undamaged; replace any stripped or broken hardware

Right side

The Rail Assembly is an OEM part for LG dishwashers. It is a part that supports and guides the motion of the dish racks in and out of the dishwasher. The rail assembly is designed with precision fits and smooth surfaces to allow easy extension and retraction of the racks.

Causes of a bad dishwasher rail assembly can include wear and deterioration over time, damage from heavy loads that put stress on the rails, or impact damage from accidental handling.

Symptoms of a bad rail assembly include:

• Difficulty extending or retracting the dish racks
• Noisy or grinding sounds when operating the racks
• Misalignment of the racks that causes dishes to rub or stop moving properly
• Leaks or pooling of water inside the dishwasher door

This LG part is also compatible with some Kenmore models.

Replacement rack restores usable storage and support inside the appliance so dishes, containers or cookware sit securely. Simple swap for a damaged, bent or missing shelf to get your appliance back to normal organization and use. What it does:

• Provides a stable shelf surface for storing cookware, dishes or food containers.
• Replaces racks with bent wires, broken supports or missing shelving.
• Helps prevent items from tipping or sliding during normal use.
• Designed to work with the appliance's original shelf mounts and guides.

• Disconnect power (or unplug) the appliance before handling internal parts.
• Handle edges carefully — metal shelves can have sharp points where wires are bent or clipped.
• Slide the rack into the existing tracks or clips; removals may require lifting the front slightly to clear stops.