79573163160 Parts

This is a refrigerator drawer guide assembly that supports and guides a crisper/vegetable bin so it slides smoothly in and out. Replacing a worn guide restores proper drawer alignment and easy operation.

• Provides the track surface for the vegetable/crisper drawer
• Helps correct sticking, binding, or a sagging/misaligned drawer
• Can reduce scraping noises and uneven drawer movement
• Restores smooth sliding action after wear or damage

• Unplug the refrigerator before service
• Remove the affected drawer and any shelf above it for access
• Retain and transfer any screws or clips from the original guide
• Test drawer movement and alignment before closing up

This replacement gasket seals the Home Bar (door-in-door) access panel on your refrigerator. A fresh, flexible seal stops warm-air leaks that cause condensation, frost, and temperature fluctuations, helping the unit run efficiently and keep food cold.

• Forms an airtight seal around the Home Bar/door-in-door panel
• Helps maintain proper interior temperature and humidity
• Common symptoms: visible gaps, torn or warped gasket, condensation or frost near the panel, door not closing flush
• Restores reliable closing and reduces unwanted airflow

• Disconnect power before servicing
• Open the Home Bar panel, pull the old gasket from the channel, then align and press the new gasket fully into the groove—seat corners first
• Warm the gasket (hair dryer on low or soak in warm water) to relax folds; do not overheat
• Close and check for an even seal; adjust by massaging the gasket into place as needed

An in-line union for appliance tubing, this tube connector joins two sections of plastic line to create a secure, leak-resistant connection in the water circuit, ideal for restoring flow after a repair, trim, or reroute. What it does:

• Connects two lengths of compatible plastic tubing to form a continuous run
• Helps maintain proper water delivery through the appliance's water system
• Can address leaks, drips, or loose/failed connections at a splice point
• Useful when replacing, shortening, or rerouting tubing during service

• 1 tube connector

• Disconnect power and shut off the water supply before servicing
• Cut tubing square; ensure ends are clean, round, and free of gouges
• Insert tubing fully into the connector until seated, then perform a gentle pull test
• Restore water and inspect all joints for leaks; use the connector size that matches your tubing's outer diameter

This center hinge assembly supports the refrigerator door at the mid-hinge position and allows smooth, reliable pivoting. Replacing a worn hinge restores proper alignment so the door closes and seals as designed.

• Provides the pivot point at the center hinge location
• Supports door weight to maintain alignment and clearance
• Helps ensure even gasket contact for an effective seal
• Common symptoms: door sagging or rubbing, squeaking at the hinge, difficulty closing, visible play or damage at the hinge pin

• Unplug the appliance and remove items from the door to reduce weight
• Support the door while removing the center hinge fasteners
• Note and transfer any spacers/washers in the same order and orientation
• After installation, align the door and verify the gasket seals evenly

Replacement drawer tray assembly that restores the interior storage surface of a refrigerator drawer, keeping foods contained and organized. Fits in place of a damaged or missing tray to help return normal drawer seating and use. What it does:

• Provides a stable surface for refrigerated items and keeps loose items from falling into the compartment below
• Replaces cracked, warped or broken trays that cause uneven seating or poor containment
• Helps the drawer sit and slide correctly when the tray is seated properly
• Keeps spills and crumbs contained on a removable surface for easier cleaning

• Remove all food and pull the drawer out to access the tray; your user manual for proper drawer removal steps
• Align the new tray with the drawer guides and seat it fully until it snaps or rests in the correct position
• Handle edges carefully; wear gloves if the old tray is cracked or jagged

Replacement door basket that restores convenient storage on the appliance door, keeping bottles and small items secure and accessible. Replaces damaged or missing door bins to help keep your appliance door organized and usable. What it does:

• Provides a secure shelf on the appliance door for bottles, condiments and small containers.
• Replaces cracked, chipped or broken door bins that no longer hold items safely.
• Restores lost or reduced door storage capacity for easier organization.
• Helps prevent items from falling out of the door during normal use.

• Disconnect power (unplug or switch off) and remove all items from the door before starting.
• Most installations are hand-operated: lift or tilt the old bin out of the door track, then seat the replacement into the same track—do not force.
• Inspect mounting clips or supports during replacement; damaged clips must be replaced separately.

The Defrost Heater is an OEM part for LG French door refrigerators. It is an electrical heating element located inside the fridge compartment or freezer that automatically activates to melt frost and ice buildup during defrost cycles. Subject to temperatures cycling between warm and cold, the heater coil must withstand expansion stresses. 

Symptoms of a bad defrost heater include:

• Accumulating frost that decreases available storage space over time  
• Extended defrost periods not fully melting all accumulated ice
• Buzzing or clicking coming from the refrigerator compartment 

Causes can be cracks in the heater coil's insulation allowing moisture to penetrate over many years of use. Replace with this new OEM LG defrost heater to ensure automatic removal of frost for fresher food storage. It is also compatible with Sears/Kenmore French door models.

This button assembly replaces a damaged or worn control-panel button cluster to restore reliable button response and user control. It fits into the appliance's console and provides the tactile interface needed to select cycles and settings. What it does

• Replaces the control-panel button cluster so unresponsive, stuck, or missing buttons can be fixed.
• Restores tactile feedback and reliable electrical contact for user inputs.
• Helps resolve intermittent or non-working button inputs when the switch/buttons are the cause.
• Matches the OEM form to fit into the factory console opening.

• Disconnect power (and water, if applicable) before starting any repair.
• Access typically requires removing the console or control panel.
• Handle the assembly and ribbon/contact connectors carefully to avoid damage.

This case assembly is the outer housing for the Magic Room compartment, restoring proper fit and protection for internal components. Replaces a cracked, warped or damaged compartment case to help maintain compartment integrity and appearance. What it does:

• Provides the structural housing for the Magic Room compartment and secures internal components
• Restores proper alignment and fit to prevent rubbing or interference with doors/drawers
• Helps maintain an even internal compartment environment by sealing the compartment area
• Addresses visible damage such as cracks, broken mounting tabs or deformation

• Refer to the refrigerator's service manual for disassembly/reassembly steps and proper fastener torque
• Disconnect power to the appliance before starting any repair to avoid electrical hazard
• Handle plastic components carefully to avoid further cracking; replace any broken mounting clips
• Replace damaged screws or brackets with OEM-specified hardware for a secure fit

This cover assembly protects the machine components and helps keep internal machinery free of debris and accessible for repair. It provides a durable barrier that helps extend component life and maintains safe operation. What it does:

• Shields motors, belts and internal linkages from dust and lint that can cause wear
• Helps contain moving parts to reduce pinch or contact hazards during normal use
• Maintains proper component alignment by providing a stable mounting surface
• Commonly replaced when cracked, warped, missing fasteners, or damaged from impact

• One cover assembly as shown

• Disconnect power before attempting service
• Handle gently to avoid cracking plastic tabs; inspect mounting clips and screws for damage
• Reuse original fasteners only if undamaged; replace any stripped screws or broken clips

A replacement fan grill assembly that protects the appliance's fan while helping direct airflow for proper cooling. Restores a finished appearance and replaces cracked, broken, or missing grilles to help maintain normal ventilation. What it does:

• Protects the fan blade from debris and accidental contact
• Helps channel airflow for efficient fan operation
• Reduces rattling by securing the fan area
• Replaces damaged or cracked grilles that can restrict airflow

• Disconnect power to the appliance before attempting any repair.
• Typical installation uses existing screws or clips; retain mounting hardware and note orientation before removal.
• Handle carefully to avoid bending the grille or cutting hands on edges.

This rail guide assembly keeps a drawer or sliding component aligned and operating smoothly, restoring proper travel and reducing binding or noise. It replaces worn or damaged guides to help parts open and close reliably. What it does:

• Provides a stable track for drawer or panel travel to prevent sticking or misalignment
• Reduces grinding, scraping, or rattling caused by worn guide surfaces
• Keeps moving parts centered to support smooth, even sliding motion
• Restores correct clearance when original guide is cracked, broken, or bent

• Disconnect power and remove any product panels or drawers before starting
• Typical install requires basic hand tools; handle plastic parts gently to avoid breakage
• Verify proper orientation and engagement of guide with mating slide before reassembling

This filter cover replaces the damaged or worn cover that holds the air filter in place, helping maintain correct filter position and airflow for proper operation. It's a direct-fit replacement designed for easy swap-out. What it does

• Secures and protects the air filter inside the unit so the filter seals and sits correctly.
• Maintains proper airflow path to help the system run as designed.
• Prevents debris from bypassing the filter and entering internal components.
• Helps reduce rattling or vibration caused by a loose or broken cover.
• Restores the intended fit and finish of the filter compartment.

• One filter cover

• Disconnect power or remove batteries before removing the old cover to avoid fan or electrical hazards.
• Remove the old cover by releasing clips or screws; align replacement and engage clips or reinstall screws securely.
• Do not force the cover—ensure filter is seated correctly before closing to avoid damage.
• Replace hardware with OEM-equivalent parts for proper fit.

This replacement drawer guide helps the freezer/refrigerator drawer slide smoothly and stay aligned for reliable opening and closing. It restores stable support and reduces sticking or noisy movement. What it does:

• Guides the drawer along its track so it opens and closes smoothly
• Supports the drawer weight to prevent sagging or misalignment
• Helps eliminate binding, catching, or uneven movement
• Reduces scraping or rattling noises caused by a worn guide

• Disconnect power to the appliance or unplug before beginning any work
• Remove the drawer and any contents to access the guide mounting points
• Align the guide with the existing track and secure using the original screws or fasteners
• If mounting hardware is damaged or missing, replace with OEM-specified fasteners; do not force parts into place

This drip tray catches and channels water runoff inside the appliance to help prevent pooling and minor leaks. It's a direct-fit replacement listed by the manufacturer and sold as the single tray used in the unit. What it does

• Collects condensate or defrost water and directs it to the drain area to prevent pooling.
• Helps stop water from dripping onto lower drawers, shelves or the floor.
• Commonly replaces a cracked, warped or missing tray that causes visible leaks or water buildup.
• Fits into the appliance's lower compartment where the original tray sat.

• Unplug the appliance or disconnect power before servicing.
• Remove any obstructing drawers or shelves to access the tray location; handle glass shelves carefully.
• Lift out the old tray and set the new tray into the same position; no special tools typically required.