7962927 Parts

This heater assembly replaces the dryer's heating element and housing to restore warm airflow for drying cycles. It's a direct-replacement assembly that re-establishes the appliance's heat source when the dryer won't heat properly. What it does:

• Houses the electric heating element that produces heat for drying cycles
• Replaces a burned-out element, open circuit, or damaged housing that can stop the dryer from heating
• Helps resolve symptoms such as no heat, only air tumbling, or weak/partial heating
• Works with the dryer's blower and thermostat to deliver consistent drying temperatures

• One heater assembly (heating element installed in housing)

• Disconnect power to the dryer (unplug or shut off breaker) before servicing
• Allow components to cool and wear gloves to protect hands from sharp edges
• Verify the part number matches the dryer's parts list before installation

This holder assembly is a direct replacement mounting bracket that secures refrigerator internal components so they stay properly positioned and function reliably. Replaces a cracked or loose bracket to restore stable support and reduce rattling. What it does

• Secures internal components or assemblies to the cabinet to prevent shifting and vibration
• Restores proper alignment when a cracked or broken holder causes loose parts
• Helps stop rattling, knocking, or intermittent contact caused by a failed mount
• Works as a structural replacement—matches OEM fit and mounting points

• One holder assembly

• Disconnect power (unplug or shut off breaker) before starting any repair
• Remove nearby shelves, bins, or trim for access as needed; keep small fasteners organized
• Typically installs with basic hand tools; do not overtighten fasteners to avoid cracking
• If the part attaches to electrical components, verify connectors are secure before restoring power

The Water Inlet Valve is an OEM replacement part specific to LG washing machines. It is an electronic solenoid valve located near the water supply inlet ports that controls the flow of water into the washer tub. The inlet valve precisely regulates water levels during different phases like filling, washing, rinsing, and spinning cycles.

Causes of a bad water inlet valve can include worn or faulty electronic components, mineral buildup obstructing valve movement, or damage to seals and diaphragms.

Symptoms of a bad water inlet valve include:

• Inability to properly fill the washer tub during cycles
• Water leaking or flooding from the valve area
• Erratic water temperature or varying fill levels between loads
• Cycles failing to advance due to inadequate or unregulated water flow

This OEM LG part is also compatible with Sears/Kenmore models.

The Pulsator Cap is an OEM part for LG washing machines. It is designed to secure the pulsator (or agitator) in place, ensuring proper movement of the wash plate during the wash cycle. This component helps in the effective distribution of water and detergent, promoting thorough cleaning of clothes.

You should replace this pulsator cap if it becomes damaged, lost, or worn out. Causes of a bad pulsator cap can include regular wear and tear, exposure to heavy loads, or damage from improper handling. A compromised cap can lead to inefficient washing and potential damage to the pulsator.

Symptoms of a bad Pulsator Cap include:

• The pulsator becoming loose or dislodged
• Unusual noises during the wash cycle
• Clothes not being cleaned properly
• The washer experiencing imbalance issues

This OEM LG part is also compatible with Sears/Kenmore models.

This washer motor stator assembly is the stationary windings of the direct-drive motor. Replacing a weak or shorted stator restores smooth drum tumbling and strong, consistent spin performance so wash cycles complete properly.

• Creates the rotating magnetic field that drives the rotor and spins the inner basket
• Works with the rotor to provide torque for wash/tumble and high-speed spin
• Common symptoms: drum won't spin or tumble, stops under load, or motor hums without turning
• Burnt odor or visible heat damage on windings can indicate stator failure

• Disconnect power and turn off water; access the motor from the rear panel
• Remove the rotor center bolt and slide off the rotor; strong magnets—handle carefully
• Unbolt and remove the stator; transfer/reconnect the motor position (Hall) sensor and harness if present
• Tighten fasteners evenly; verify drum rotates freely by hand before restoring power

This thermistor assembly monitors water temperature inside the washer tub and relays a precise signal to the control board. Replacing a failed sensor restores accurate temperature sensing and helps prevent cycle errors and performance issues. What it does:

• Measures wash water temperature and sends the signal to the electronic control
• Enables the control to adjust cycle operation based on temperature feedback
• Common failure signs: tE/TE error codes on some models, incorrect temperatures, long cycles, or cycles that won't advance
• Intermittent faults may cause sporadic errors or inconsistent performance

• 1 thermistor assembly

• Disconnect power and shut off water before servicing
• Access location varies by model; the sensor is typically mounted in the outer tub or heater housing
• Unplug the harness, pull the old sensor straight out; seat the new sensor fully and reconnect the harness
• Route wiring away from moving parts; restore power and run a test cycle, checking for proper operation and any leaks around the sensor port

This replacement nut secures bolts or studs in your appliance. Replacing a missing or stripped nut restores a tight, reliable connection to keep brackets and assemblies stable and reduce vibration or rattling. What it does:

• Provides threaded retention for bolts/studs on panels, brackets, and assemblies
• Helps maintain alignment and stability during operation
• Typical failure signs: stripped threads, missing hardware, loose or rattling components, vibration
• Direct replacement for the original nut in the same location

• 1 nut

• Disconnect power before service; shut off the water supply
• Match thread size/pitch to the original; start threads by hand to avoid cross-threading
• Tighten with the correct tool; do not overtighten or damage mating parts
• Reinstall any washers/spacers in the original order and verify secure fit

This tapping screw fastens appliance panels and components for a secure, lasting hold. Replace stripped, rusted, or missing hardware to restore proper fit, reduce vibration and rattling, and keep brackets, covers, and trim tightly in place.

• Fastens metal or plastic panels, trim, or brackets to the appliance cabinet/frame
• Cuts its own threads in pre-drilled holes for a tight, reliable fit
• Helps maintain alignment and reduce movement that can cause noise
• Replace when the original screw is missing, stripped, corroded, or will not tighten

• Disconnect power and shut off water/gas before servicing
• Match the screw's position and length to the original hardware
• Start by hand to avoid cross-threading; tighten snugly—do not overtighten
• Reuse any washers or spacers from the original assembly if present

This is a top cover for top-loading washing machines. It is a square panel that is fitted next to the lid on the appliance. It holds everything in place and has several cut-out areas for the lint compartment and other components of the machine. This part is made of strong materials but can be damaged over time. If it is broken or missing, the part should be replaced.When replacing the top cover, unplug the washing machine and shut off the water supply first. A pair of work gloves can be used to protect the hands. Open the door and look near the door opening for screws. Use a Phillips screwdriver to remove them. Lift up on the front edge of the top of the machine and access the other fasteners. Remove the top cover and place the new part in the same location. Reattach it to the washing machine while making sure everything is properly lined up.The top cover is sold individually and directly sourced from the manufacturer. This is an authentic OEM replacement part that fits Kenmore and LG washing machines.

This thermostat assembly regulates refrigerator temperature to help keep food safely chilled. It replaces a failing temperature control so the compressor and fans run at the right times for stable cooling. What it does:

• Senses cabinet temperature and signals the compressor or evaporator fan to cycle on/off
• Restores correct cooling when a faulty thermostat causes inconsistent temperatures
• Helps stop excessive run time or constant warm conditions caused by a bad control
• Works as the temperature-control component in the refrigerator's cooling system

• Disconnect power before servicing to avoid electrical shock
• Handle the capillary tube and bulb carefully—do not kink, clamp, or crush
• Mount and route the thermostat per OEM orientation; secure all fasteners and electrical connections