Jenn-Air Aws 1090 Parts

Idler lever kit for Speed Queen washers. Maintains belt tension for smooth drum rotation. Replace if lever is cracked, pulley worn, or mechanism damaged.

Washer won't fill with water or only fills with hot? The water inlet valve controls water flow into the tub. DIY repair takes about 30 minutes.

This is a control knob for washing machines. This control knob is used to adjust the water temperature and level settings on the unit. It is manufactured out of a white plastic. The replacement is very easy and takes less than 15 minutes to complete. All that this process involves is pulling the old knob off and sliding the new knob on.A new control knob will be needed if the original is cracked, broken, or damaged in any way. Over time, the white plastic may begin to yellow, and the user may wish to replace the control knob for cosmetic purposes. If the knob is not actuating the desired cycle, it will need to be replaced.This control knob is a genuine SpeedQueen part and is an OEM part sourced directly from the manufacturer. It is sold individually. This specific control knob is compatible with washing machines that are manufactured by the SpeedQueen brand.

Fix water leaking from the bottom of your washer with a new drain pump. This part removes water at the end of each cycle. Direct replacement, moderate DIY.

Replacement lid for Speed Queen washers. Covers the washing drum and provides access for loading clothes. Replace if rusted, cracked, or has sharp edges.

This mixing valve blends hot and cold water to deliver a consistent, tempered supply to the machine. Replacing a worn valve helps restore proper fill temperature control and dependable washing performance.

• Regulates and mixes incoming hot and cold water to a set outlet temperature
• Helps maintain stable warm water fills during cycles
• Designed to fit and function like the original component it replaces

• Disconnect power and shut off both water supplies before service
• Place a towel or pan to catch residual water when removing hoses
• Note hose orientation and tighten fittings securely to prevent leaks
• After installation, restore water and power, then check for leaks and proper fill temperature

Supports the rotating shaft for smooth, quiet operation. Replace when you hear grinding noise or excessive vibration during spin cycle. Confirm fit with your model.

Replace this washer hub and seal kit when you notice water leaking from the center shaft or loud noises during spin cycle. Confirm fit with your model.

Washer won't advance cycles, keeps filling, or skips rinse/spin? Timer controls cycle sequences. Moderate DIY repair restores proper wash timing.

White timer knob for washers. Mounts on the timer shaft to replace a cracked, broken, or missing knob. Restores your ability to select and adjust cycles.

Cosmetic bezel ring that mounts behind the timer knob on your washer control panel. Replace if cracked, broken, or missing to secure the knob properly.

10 oz sealant cartridge forms a flexible, watertight seal around washer tubs, door boots, and panel seams. Replace when repairing leaks or resealing.

Washer stuck in one cycle or not advancing? This electromechanical timer controls cycle progression. Restores proper wash cycle sequencing and timing.

If your washer won't advance through cycles automatically and you must turn the knob manually, the timer likely failed. Moderate DIY repair restores function.

Fix a washer that stops mid-cycle or won't advance through wash, rinse, and spin. This timer restores automatic cycle progression. Moderate DIY repair.

This variable pressure switch senses water level and signals the washer to stop filling, helping maintain correct fill levels for reliable cycles. It replaces a failed or intermittent level-control switch to restore normal filling behavior. What it does:

• Detects drum water level and tells the control when to stop filling
• Helps prevent overfilling or underfilling caused by a bad level signal
• Resolves symptoms like no fill, overfill, or erratic cycle advancement
• Works as the washer's water-level sensor interface to the main control

• One variable pressure switch

• Disconnect power (and water if applicable) before servicing
• Replace only with the exact part number; match electrical connector and hose fittings
• Handle the pressure hose and terminals carefully to avoid damage