Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Specs: No.8X1/2 HEX WASHER HEAD
Replaced the control board after removing the inner door liner, plastice board cover and board itself, by removing screws, working various plastic clips/tabs and unclipping wire harnesses from board. most of time was spent cleaning the black soot from the door, which had a terrible burnt electrical/plastic fire smell. Cleaned mold/scale off of as much of the door as I could while in there as well. Removing parts without breaking plastic tabs to hold the new parts was trickiest part. Read more
Screw: 8-16 x 3/8 inch.
Trim piece that finishes the lower edge of the dishwasher tub opening. Replace if cracked, warped, or missing to restore a clean edge and smooth door operation.
I ordered a new rubber door seal for around door, new bottom door seal and spinner impeller and nut to hold on bottom arm as it looked weak. Everything worked great except bottom door seal which looks slightly different and would NOT stay on. I ended up putting back on the old one. Door doesnt leak but not sure it would even be worth it sending part back as I already tossed bag out. Other parts worked great and DW cleaning better. Read more
Secures the upper spray arm so it spins freely and stays aligned. Replace if cracked, worn, or causing wobble to restore proper water distribution.
Spun each of the three wash arms by hand. All could be made to touch/scrape but the top one was super wabbly. Ordered both the arm and clip. Repair took less than a minute. Used a screwdriver to pry loose one side of the old clip to remove. Aligned the new parts and easily snapped into place. Read more
No longer includes course threaded sleeve. When replacing upgrade to new motor. For new motor, order from parts list by model number.
Searched the dishwasher model on ApplianceParts (had used them for a washing machine repair a few years earlier). Was looking for an exploded diagram of the internal parts so I could figure out what might be the problem. There was a video for a motor seal repair kit that seemed to address the bearings which is what I suspected was the culprit. The video started by noting that "you want to replace the motor seal if 1) you have a leak or 2) your dishwasher is making a noise". I watched the... Read more
Replace the cable bracket guide roller on your dishwasher. This small wheel guides the door cable smoothly through the bracket, preventing binding and wear.
Lost or broken rinse aid cap causing spotty dishes? This dispenser knob restores tactile control for proper rinse aid release. Simple twist-on install.
Replaced the jet dry lid. Read more
This is a small plastic or metal trim piece that fits on the lower right corner edge of the dishwasher door. It provides a finished appearance and helps protect the door edge from damage. Replace this trim if it is cracked, broken, or missing, which can leave a sharp or unfinished edge on the door.
Replacement leveling leg that stabilizes and adjusts your dishwasher height for proper alignment. Needed when bent, broken, or missing to eliminate rocking.
This inner slide rail (track) supports a refrigerator/freezer drawer and restores smooth, stable gliding for the drawer. Replacing a worn or damaged rail helps stop sticking, misalignment, rattling or partial drawer drops. What it does:
What's included: One inner slide rail (track) Install notes:
Secures your dishwasher to surrounding cabinetry. Replace this bracket if it's bent, broken, or missing to restore a tight, level installation.
Followed video instructions Read more
Color: Gray. Measures about a 1/2 inch wide by 1 inch high by 1 inch deep.
Ordered replacements and installed Read more
I had to use the 12' drain hose and a longer supply line in order to make the plumbing connections. It works great. Done. Read more
Dark gray cap that covers the tip of dishwasher dishrack tines. Replace if your existing tine cap is cracked, broken, missing, or worn to protect dishes.
Foam insulation liner that installs behind the dishwasher toe kick panel. Replace if torn, compressed, missing, or damaged to restore cabinet insulation.
Includes 6` Stainless Steel Braided Hose, Power cord & Connectors
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.