Adee9rgs175w01 Parts

This front bulkhead assembly replaces the dryer or washer front panel that supports the drum and front bearings, restoring proper drum alignment and enclosure. It helps reduce vibration, air leaks, and rubbing that can cause noise or wear. What it does:

• Supports the drum and front bearing to keep the drum centered during operation
• Provides the mounting surface for the door and front seal to maintain proper airflow and closure
• Prevents drum-to-frame contact that can cause squeaks, scraping, or excess vibration
• Helps keep lint and moisture contained in the drum area to protect internal components

• Disconnect power (and water, if applicable) before starting any repair
• Remove the dryer/washer door and front cover to access mounting fasteners; keep hardware for reassembly
• Transfer any door latch, seal, or trim pieces to the new bulkhead as needed
• After installation, recheck drum rotation and clearances; run a short test cycle to confirm quiet operation

This electronic wiring harness connects the control components and provides the indicator light needed for proper operation of a 1-phase Speed Queen washer. It replaces a damaged or worn harness to restore electrical continuity and visual status feedback. What it does:

• Links the control board, switches, sensors and indicator light so commands and status signals pass correctly
• Provides the harness routing and connector set used on compatible 1-phase washer control assemblies
• Commonly replaced when the machine has no power to controls, no indicator light, or intermittent control operation
• Helps resolve electrical faults caused by chafed wires, broken terminals, or connector failure

• Disconnect power before servicing to avoid shock or damage
• Handle connectors gently; match keyed connectors and secure all locking tabs
• Route harness away from sharp edges, hot components and moving parts; follow OEM routing and fasteners

This right-side end cap is a replacement trim piece that restores the finished appearance of the washer control/top edge and protects edges from wear. It matches the original shape and color for a clean factory look. What it does:

• Covers and protects the right edge/end of the control/top trim to prevent exposed edges
• Restores appearance when the original cap is cracked, broken or missing
• Helps keep the trim secured and reduces the chance of snagging or catching
• Matches factory color and fit for a seamless replacement

• Disconnect power to the appliance before beginning any repair.
• Remove the affected trim or panel per the service manual to access the end cap.
• The cap typically snaps or slides into place; use a plastic pry tool to avoid damaging surrounding trim.

This is a tapping screw with a hex head and Torx drive designed to fasten panels and components on Speed Queen laundry appliances. It provides a secure, vibration-resistant hold for repeatable service and repairs. What it does

• Fastens outer panels, brackets and internal parts where a self-tapping screw is required
• Holds components tight to prevent rattling or misalignment during operation
• Replaces missing, worn or stripped screws that cause loose or insecure parts
• Used when a screw must tap its own threads in sheet metal or thin substrates

• One tapping screw (hex head Torx)

• Use the correct Torx driver bit to avoid stripping the drive recess
• Drive straight and steady; do not over-torque to prevent thread or sheet-metal damage
• Follow OEM service instructions for panel removal and fastening order
• Disconnect power and follow safety precautions before servicing the appliance

A replacement low-profile Phillips screw used to secure panels and components on compatible laundry equipment. Provides a secure, low-profile fastening where a shorter head is required. What it does:

• Fastens trim, control panels, or small brackets where a low-profile head is needed
• Restores secure attachment when original screws are missing or stripped
• Helps eliminate rattling or loose panels caused by missing hardware
• Matches common #8 AB-18 x 1/2" thread and length for specified OEM fittings

• Use the correct Phillips screwdriver to avoid cam-out and head damage
• Start threading by hand to avoid cross-threading; do not force
• Tighten until snug—do not over-torque to prevent stripping the mating threads
• If threads are damaged, replace with an appropriate fastener or repair the hole before installing

This is a 8-AB-16 x 3/4 Phillips truss-head screw used to fasten appliance panels and components. It provides a low-profile, wide bearing surface to hold trim, guards, and light assemblies securely. What it does:

• Fastens panels, trim pieces, brackets and lightweight assemblies
• Wide truss head distributes load to prevent surface damage
• Phillips drive for common screwdriver or bit compatibility
• Helps stop rattling or loose panels when a worn or missing screw is replaced

• Use the correct #2 Phillips driver to avoid stripping the head
• Thread into original hole; do not force if threads feel damaged
• Tighten snugly but avoid overtightening to prevent stripping or cracking surrounding material
• Keep removed hardware organized for reassembly; replace any damaged mating parts

This left-side cabinet panel restores the exterior side of the washer/dryer cabinet for a clean, finished appearance and cabinet stability. It replaces a dented, rusted, or damaged side panel to improve looks and protect internal components. What it does:

• Replaces a damaged or corroded left cabinet side to restore cabinet strength and appearance
• Covers and protects internal components from dust and accidental contact
• Helps prevent moisture and debris from reaching internal parts that can cause wear
• Returns the cabinet to a flush, finished profile for proper enclosure fit

• One left cabinet side panel (single piece, as shown)

• Disconnect power and water before starting work
• Remove adjacent panels or trim as needed to access mounting screws; keep hardware for re-use unless damaged
• Handle edges carefully—wear gloves to avoid cuts and alignment damage
• Test fit and align before tightening fasteners to ensure proper panel gaps and secure fit