Adg3lrs111tw01 Parts

Secures and routes wiring at the fabric selector. Replace if cracked, broken, or missing to keep wire connections tidy and prevent harness damage.

Cushions drum contact points to reduce noise and metal wear in your dryer. Replace when worn, torn, or missing to restore quiet operation. Confirm fit with your model number.

This replacement knob assembly with skirt restores a secure, easy-to-turn control interface on the appliance. It provides a finished look while allowing reliable selection of settings. What it does:

• Replaces a cracked, stripped, or missing control knob to restore user control
• Provides a stable grip and tactile feedback when turning settings
• Helps prevent accidental slips or selector misalignment caused by worn knobs
• Matches the original mounting style for a direct-fit replacement

• Disconnect power (unplug or switch off breaker) before starting any repair
• Remove the old knob by pulling straight off the control shaft; install the new knob by aligning and pushing fully onto the shaft
• If the original used a retaining clip or set screw, verify and reinstall it; only use parts explicitly included

Can't hear when your dryer cycle ends? This buzzer restores audible end-of-cycle alerts and warning signals. Adjustable volume, easy installation.

This left-side white panel end replaces a damaged or worn corner trim on the control console or front fascia to restore appearance and protect edges. Designed to match original fit and finish on compatible Speed Queen units. What it does:

• Covers and protects the left edge of the console/front panel from bumps, wear, and moisture.
• Restores a clean, finished look when the original panel end is cracked, chipped, or missing.
• Helps maintain proper alignment and support for adjacent trim and fasteners.
• Fits in place of the factory left-side panel end for straightforward cosmetic repair.

• Designed for direct replacement; reinstall using original screws/clips when present.
• Inspect adjacent trim and fasteners; replace any damaged clips to ensure secure fit.
• Power down and unplug the appliance before attempting any repairs that require panel removal.

Secures internal components inside your dryer cabinet. Replace if bent, cracked, stripped, or missing to restore proper alignment and stability.

This blower housing encloses the dryer's blower wheel and routes air from the drum through the lint system to the exhaust. Replacing a cracked or warped housing restores proper airflow, reduces vibration, and helps resolve extended dry times.

• Encloses and supports the blower wheel while channeling intake and exhaust airflow
• Helps maintain consistent drying performance and temperature regulation
• Typical failure symptoms: longer cycles, weak vent airflow, excess lint inside the cabinet, scraping or rattling near the blower
• Visual clues: cracks, broken mounting tabs, or housing out-of-round causing wheel contact

• Disconnect power; for gas units, also shut off the gas supply
• Access from the front: remove front panel and lint duct to reach the blower assembly
• Transfer the blower wheel, gasket/seals, and mounting hardware from the original housing as needed
• Seat the housing squarely; the blower wheel spins freely and clear lint buildup before reassembly

If your dryer is vibrating excessively or making loud thumping noises, a worn drum roller bracket may be the cause. This bracket restores smooth rotation.

Self-tapping hex washer head screw secures plastic trim and sheet-metal panels on dryers. Replace worn, stripped, or missing screws during repairs.

This resistor assembly is a direct replacement electrical component that restores proper resistance in the appliance's control circuit, helping restore reliable operation and electrical continuity where the original resistor has failed. What it does:

• Provides the correct resistance in the control/electrical circuit so related components operate as designed
• Commonly replaces a failed or open resistor causing intermittent operation or control faults
• Can help stop symptoms such as erratic cycles, failure to start, or control-board error indications tied to resistance faults
• Works as a like-for-like replacement when the original resistor assembly is damaged or shows out-of-spec resistance

• Disconnect power to the appliance before servicing to avoid electrical shock
• Handle the assembly carefully and avoid touching contact surfaces; observe ESD precautions if present
• Verify connector fit and secure all fasteners; confirm correct orientation before re-applying power

Replace a stripped or broken motor pulley that prevents your dryer drum from turning. Direct-fit part restores belt engagement and motor rotation.

This wave washer is a spring-style spacer used in washer assemblies to apply tension and maintain proper spacing. It controls endplay so parts fit securely and the machine runs smoothly with reduced vibration and noise during wash and spin cycles.

• Provides spring preload to maintain correct spacing in rotating assemblies
• Helps limit endplay that can cause rattling, chatter, or intermittent engagement
• Can help address symptoms like metallic noises, excessive play/wobble, or rough operation during agitation or spin
• Replace if the original washer is flattened, cracked, or missing

• Disconnect power and turn off water before servicing
• Note the exact stack order and orientation of spacers/shims during disassembly
• Install the new wave washer in the same orientation; do not bend or deform it
• Reassemble and hand-rotate components to check for smooth operation before test-running

Seals the back of the dryer drum to prevent air leaks and maintain proper alignment. Replace if you notice poor drying or air escaping. Confirm fit with your model.

This right-hand white panel end replaces a damaged or worn side cap to restore the washer's appearance and keep the cabinet edge protected. It fits the machine's front panel area and matches factory styling. What it does:

• Covers and protects the right-hand side edge of the front cabinet or console
• Restores the unit's finished appearance after damage, scratches, or missing trim
• Helps prevent exposure of internal edges and wiring along the cabinet side
• Matches factory color and mounting locations for a clean replacement

• Remove power and disconnect the appliance before beginning any repair.
• Minor disassembly of the front panel or console may be required to access mounting tabs.
• Handle edges carefully to avoid cutting yourself or scratching the finish.
• Replace missing or damaged fasteners with matching hardware for secure fit.

If your dryer motor vibrates excessively or makes rattling noises, this motor mount clamp secures the motor to the cabinet for stable, quiet operation.

Washer adhesive is a clear sealant used to secure various internal components and create watertight seals within the washing machine. Use this adhesive when experiencing water leaks, loose parts, or when replacing gaskets and seals during repairs.