Ars366zbc Parts

This base pan drain valve channels defrost and condensation water from the refrigerator base pan to the drain system, preventing standing water and ice buildup. It's a direct-replacement part that restores proper draining and helps maintain normal cooling performance. What it does:

• Directs melt and condensation from the base pan into the drain line to prevent pooling.
• Re-establishes proper water flow when a cracked, clogged, or broken drain outlet is causing leaks or puddles.
• Reduces odor and freeze-up risk by preventing stagnant water in the base pan.
• Works with the fridge's drain system; not an electrical component.

• Disconnect power to the appliance before starting any repair; also shut off water if the model has a connected water supply.
• Remove the kick plate/base cover and access the base pan to reach the drain valve.
• Inspect mating seals and the drain tube; replace degraded seals or clear any obstructions to ensure proper drainage.
• After installation, test by pouring a small amount of water into the base pan drain area and confirm it flows through the valve without leaking.

This escutcheon is the outer trim piece that finishes the appliance control area, restoring a clean look and protecting internal controls from spills and damage. It's a simple cosmetic and protective replacement. What it does:

• Covers and protects the control panel opening and switch hardware from moisture and debris
• Restores a finished appearance when the original trim is cracked, warped, or discolored
• Helps hold control switches and buttons in proper alignment
• Reduces drafts and prevents loose edges that can catch on clothing or cookware

• One escutcheon (control panel trim) as shown

• Disconnect power to the appliance before starting any work to avoid shock or injury
• Removal/installation typically requires removing a few screws or clips from the control panel—keep hardware for reuse unless new fasteners are provided
• Handle the new escutcheon carefully to avoid scratching the finish during installation

The Ice Chute Door is an OEM replacement part for Whirlpool side-by-side refrigerators. It provides access to the dedicated ice and water storage and dispensing compartment located on the refrigerator door.  

Causes of a faulty chute door can include normal wear from frequent use. Internal temperature fluctuations may cause durability issues over several years.

Symptoms of problems include:

• Failure to fully close or form a tight seal  
• Difficulty dispensing ice or water due to door misalignment
• Premature cooling loss from unsealed opening
• Physical damage preventing proper closing

This OEM door is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore side-by-side refrigerators.

The Defrost Thermostat is an OEM part for Whirlpool refrigerators. This thermostat regulates the temperature within the defrost cycle, ensuring that the defrost heater activates and deactivates at the appropriate times to prevent frost buildup on the evaporator coils.

Causes of a bad defrost thermostat can include electrical failures, wear and tear over time, or damage from temperature fluctuations. 

Symptoms of a bad defrost thermostat include:

• Excessive frost buildup in the freezer
• The refrigerator not maintaining proper temperature
• The defrost heater not turning on
• Water leakage inside the refrigerator

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This gallon sized fresh food door bin may come in white or clear depending on what the manufacturer provides at the time. This bin measures about 17 inches wide by 4 inches high by 8 inches deep.

This overload is a thermal protection device that mounts on the motor/compressor and opens the circuit when excessive heat or current is detected. Replacing a weak or failed overload helps restore safe startup and protects the windings from damage. What it does:

• Monitors motor/compressor temperature and current draw
• Interrupts power on overheat/overload to prevent damage
• Aids troubleshooting of start/run issues when paired with the start device
• Common symptoms: hums then clicks off, won't start, intermittent shutdown, frequent tripping

• 1 thermal overload protector

• Disconnect power before servicing; allow components to cool
• Access the terminal area on the motor/compressor; remove any cover
• Note/photograph wire positions; transfer wires and fully seat the new overload on the correct terminal
• Inspect the start relay, capacitor, and terminals for heat damage; replace any compromised parts