Atw4475vq Parts

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Includes drive tube spacer, "T" bearing and both shaft seals.

This brake release cam works with the washer's brake assembly to disengage the brake during spin and re-engage it at stop. Replacing a worn cam restores smooth basket spin and reduces squeal or grinding at spin transitions.

• Disengages the brake so the basket can spin; helps reapply the brake as the cycle ends
• Supports smooth starts and stops of the spin cycle
• Worn or damaged cams can cause no spin or intermittent spin
• Common symptoms include loud squeal/grinding at start/stop or a burning odor near the brake area

• Disconnect power (and water supply, if moving the washer) before service
• Access the brake/basket drive area; the brake spring is under tension—use caution and eye protection
• Note orientation of parts before removal; seat the new cam correctly
• After reassembly, run an empty spin test to verify operation

Used from harness to top.

This is the water pump that moves water through your appliance so cycles can run correctly. Replacing a failing pump restores proper water flow and helps prevent standing water, poor performance, and leaks. What it does:

• Circulates and/or removes water as the appliance operates
• Supports proper flow so wash/rinse/drain steps can complete
• Maintains a sealed path at the pump connections to help prevent leaks
• Typical symptoms of a failing pump: standing water, weak/no water movement, loud humming or grinding from the pump area, leaks, or related drain/circulation errors

• 1 water pump

• Disconnect power and shut off water supply before servicing
• Have towels/containment ready; some residual water is normal when hoses are removed
• Move wires and hoses one-for-one to the new pump; tighten clamps and check any O-rings/seals
• Run a short test cycle and inspect for leaks and proper water movement

This is a Whirlpool washer inner tub spin basket. The spin basket is the portion of the washing machine the clothes are held. This piece must operate efficiently for the items in the washer to be thoroughly cleaned. The main indicators of a damaged spin basket are the loss of the ability to spin or the washer making loud noises due to moving and rattling of the spin basket.Begin installing the new basket by unthreading the screws that fasten the top portion of the washer to the base. Tilt this back, and use a screwdriver to unfasten the clips that hold the top of the tub in place. Remove the fabric softener reservoir from the center of the basket. Use a socket to unbolt the agitator at the bottom of the tub. Once this is removed, reach down and lift out the old tub. Complete these instructions in reverse to install the new unit.This is a genuine OEM part sourced directly from the manufacturer. This product is compatible with Whirlpool, Amana, Roper, Kenmore, and Maytag appliances.

Used for the pressure switch.

Right hand side

This water level pressure switch monitors the tub's water level via an air hose and signals the washer when to stop filling and move to the next step. Replacing a failed switch restores accurate fills and reliable cycle operation.

• Senses tub water level through air pressure and communicates with the timer/control
• Shuts off inlet valves at the correct level to help prevent overfilling
• Allows the cycle to advance to wash, drain, and spin based on sensed level
• Common symptoms: overfilling/overflow, underfilling or no fill, cycle stuck at fill/sensing, no agitate or spin

• Disconnect power and turn off water supply before servicing
• Access the control console to remove the old switch; note wire locations for correct transfer
• Move the air hose to the new switch and ensure the hose is clear, undamaged, and snug at both ends
• Reassemble and run a test fill to verify proper shutoff and cycle progression

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening

Size: .20 Fl. Oz. (6 ml)

Straight knurled pin that secures knobs or small components to a shaft for a tight, slip-resistant fit. Replaces a worn or missing pin to stop loose, wobbly, or spinning knobs and restore reliable engagement. What it does:

• Secures knobs, dials or small parts to control shafts by providing a press-fit, knurled surface.
• Prevents wobble, slipping, or spinning of control knobs that won't turn with the shaft.
• Common service symptom: knob spins freely or fails to engage controls.
• Used where a small metal pin is required to lock a component onto a splined or smooth shaft.

• Disconnect power and unplug the appliance before servicing.
• Remove the knob or access panel to reach the shaft; pin is typically press-fit.
• Removal/installation may require needle-nose pliers, a small punch, or a bench press; protect surrounding parts from damage.
• Keep small parts away from children and follow appliance safety guidelines; replace mating hardware if the shaft or hole is damaged.

Replacement flexible hose that routes water inside your appliance, restoring secure flow and helping prevent leaks or drainage problems caused by cracked, kinked, or worn hoses. What it does:

• Directs water to and from appliance components during normal operation.
• Prevents leaks when hose walls and fittings are intact.
• Common symptom fix: visible leaks, water pooling beneath the appliance, or reduced/irregular water flow.
• Fits in-line with existing clamps and fittings to maintain proper routing.

• Disconnect power and shut off the water supply before starting any repair.
• Inspect and replace clamps or fittings if corroded or damaged; use proper-size clamps for a secure seal.
• Route hose without sharp bends or kinks and avoid contact with hot surfaces or moving parts.

Replace aging or leaking washer supply lines with this fill hose kit. It provides two 5-foot hoses to connect your home's hot and cold water valves to the washer, helping maintain a secure connection and consistent filling.

• Connects hot and cold water faucets to the washer's inlet valves
• Replace if hoses are leaking, cracked, bulging, or kinked
• Can help address slow filling caused by restricted or kinked hoses
• Useful when installing or relocating a washer

• Unplug the washer and shut off both water supply valves before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucet and washer
• Match hot to hot and cold to cold; hand-start threads to avoid cross-threading, then tighten firmly without overtightening
• Restore water and power; run a fill test and check all connections for leaks

Includes suspension pads.

This clutch spring cap retains and protects the clutch spring in your washer's drive/clutch assembly, maintaining proper tension. Replacing a worn or missing cap helps the clutch engage smoothly and reduces slipping and noise during spin.

• Secures the clutch spring within the clutch assembly to prevent movement or dislodging
• Maintains correct spring preload for consistent clutch engagement
• Can help reduce clutch slip that appears as weak/no spin, slow spin ramp-up, or intermittent spinning
• Common signs of trouble: rattling or scraping near the drive, burning smell, or a visibly damaged/missing cap

• Unplug the appliance and shut off water before servicing
• Access the clutch per your model's service procedure; removing the gearcase/transmission and clutch may be required
• Carefully relieve spring tension and note the orientation of the spring and cap before removal
• Inspect the spring, clutch lining, and related hardware; replace any worn components during reassembly