Awn432 Parts

This variable pressure switch senses water level and signals the washer to stop filling, helping maintain correct fill levels for reliable cycles. It replaces a failed or intermittent level-control switch to restore normal filling behavior. What it does:

• Detects drum water level and tells the control when to stop filling
• Helps prevent overfilling or underfilling caused by a bad level signal
• Resolves symptoms like no fill, overfill, or erratic cycle advancement
• Works as the washer's water-level sensor interface to the main control

• One variable pressure switch

• Disconnect power (and water if applicable) before servicing
• Replace only with the exact part number; match electrical connector and hose fittings
• Handle the pressure hose and terminals carefully to avoid damage

Washer won't drain or leaves standing water after cycles? This drain pump removes water from the tub. Common repair that restores proper drainage.

This left-side white panel end replaces a damaged or worn corner trim on the control console or front fascia to restore appearance and protect edges. Designed to match original fit and finish on compatible Speed Queen units. What it does:

• Covers and protects the left edge of the console/front panel from bumps, wear, and moisture.
• Restores a clean, finished look when the original panel end is cracked, chipped, or missing.
• Helps maintain proper alignment and support for adjacent trim and fasteners.
• Fits in place of the factory left-side panel end for straightforward cosmetic repair.

• Designed for direct replacement; reinstall using original screws/clips when present.
• Inspect adjacent trim and fasteners; replace any damaged clips to ensure secure fit.
• Power down and unplug the appliance before attempting any repairs that require panel removal.

Fix washer water leaks with this inlet valve hose. Simple repair—turn off water, remove front cover (4 screws), and replace. Takes under 30 minutes.

Secures the washer lid hinge to limit travel and maintain smooth operation. Replace this clip if worn, broken, or missing to restore proper lid alignment.

Fix washer not draining or showing error codes with this drain pump. Removes standing water during drain/spin cycles. Moderate DIY repair restores drainage.

A replacement cord lead-in that routes incoming power into the appliance and provides a secure connection point for the main wiring. Restores reliable electrical feed and helps eliminate intermittent power or no-power issues. What it does:

• Transfers household power from the external cord to the appliance's internal wiring
• Provides a stable inlet connection and strain relief for the incoming power cable
• Commonly replaced for symptoms such as no power, intermittent power, blown fuses, or visible damage/corrosion at the inlet
• Matches OEM fit and mounting for a direct replacement when the part number is correct

• One cord lead-in assembly

• Disconnect all power at the breaker or unplug the appliance before starting work
• Route wires and secure strain relief per OEM guidance; tighten terminal connections firmly but do not overtighten
• If wiring or terminal damage is present, replace or repair per local electrical code

Leaking from underneath your washer? This drive bell seal kit prevents water from entering the transmission, stopping leaks and corrosion in top-load washers.

If your washer overfills or underfills, the water level pressure switch likely needs replacement. This switch detects fill height and signals the control.

Seals the washer tub to prevent leaks and protect internal components. Replace if you notice water dripping or pooling. Confirm fit with your model.

This wave washer is a spring-style spacer used in washer assemblies to apply tension and maintain proper spacing. It controls endplay so parts fit securely and the machine runs smoothly with reduced vibration and noise during wash and spin cycles.

• Provides spring preload to maintain correct spacing in rotating assemblies
• Helps limit endplay that can cause rattling, chatter, or intermittent engagement
• Can help address symptoms like metallic noises, excessive play/wobble, or rough operation during agitation or spin
• Replace if the original washer is flattened, cracked, or missing

• Disconnect power and turn off water before servicing
• Note the exact stack order and orientation of spacers/shims during disassembly
• Install the new wave washer in the same orientation; do not bend or deform it
• Reassemble and hand-rotate components to check for smooth operation before test-running

Leaking water under your washer? This transmission tube seal stops leaks where the inner bell meets the transmission in top-load washers.

Self-cleaning washer lint filter traps debris to protect your pump and drain system. Replace when clogged or damaged to maintain proper drainage. Verify fit with your model number.

This right-hand white panel end replaces a damaged or worn side cap to restore the washer's appearance and keep the cabinet edge protected. It fits the machine's front panel area and matches factory styling. What it does:

• Covers and protects the right-hand side edge of the front cabinet or console
• Restores the unit's finished appearance after damage, scratches, or missing trim
• Helps prevent exposure of internal edges and wiring along the cabinet side
• Matches factory color and mounting locations for a clean replacement

• Remove power and disconnect the appliance before beginning any repair.
• Minor disassembly of the front panel or console may be required to access mounting tabs.
• Handle edges carefully to avoid cutting yourself or scratching the finish.
• Replace missing or damaged fasteners with matching hardware for secure fit.

Fix washer slipping during agitation or spin with a new drive insert spline. This splined component restores secure torque transfer in the transmission.

This is a small flow restrictor valve installed in the water inlet line of the washer. It regulates water pressure and prevents backflow to ensure proper fill levels during wash cycles. Replace this part if the washer is overfilling, underfilling, or if water is leaking back through the inlet when the machine is off.