Awn63rsn115tw01 Parts

A replacement shoulder screw with a 5/16-18 threaded hex flange head that secures components while providing a built-in shoulder for accurate spacing and alignment. Restores proper fit and movement where the original fastener is worn or missing. What it does

• Provides a fixed shoulder to locate or pivot panels, linkages, or assemblies.
• Threads into mating components to hold parts securely with a built-in flange head for improved bearing surface.
• Commonly used where a precise gap or bearing surface is required; worn or missing screws can cause misalignment, rattling, or loose assemblies.
• Fits applications that specify a 5/16-18 thread and hex flange head geometry.

• One (1) shoulder screw, 5/16-18 hex flange head.

• Disconnect power to the appliance and follow all manufacturer safety precautions before servicing.
• Use the correct hex socket or wrench sized for the flange head; start threads by hand to avoid cross-threading.
• Tighten snugly but avoid over-torquing; over-tightening can damage mating threads or deform the shoulder.
• If the screw locates a moving part, verify free movement and correct alignment after installation.

A specialized service wrench designed for Horizon/TL-L style Speed Queen machines to aid technicians during maintenance. Provides a secure grip for installing and removing the specific service fasteners used on these transmissions and hubs. What it does:

• Fits the Horizon/TL-L service fastener to allow controlled tightening or loosening
• Speeds routine service tasks that require the OEM service wrench
• Reduces risk of damaging the fastener when compared with improvised tools
• Useful for maintenance and repair work performed on transmission/hub assemblies

• One Horizon/TL-L service wrench

• Intended for qualified service technicians familiar with Speed Queen equipment
• Disconnect power and follow all safety procedures before servicing
• Use the tool only for its intended fastener; do not use as a pry bar or hammer
• Inspect the tool before use; replace if damaged

This tall-lip seal fits the outer tub to help keep wash water inside the tub and protect internal components from leaks. It replaces a worn or damaged outer tub seal to restore a watertight tub interface. What it does:

• Provides a watertight seal between the outer tub and adjacent components
• Helps prevent water leaks that can cause floor damage or electrical issues
• Reduces noise and vibration caused by an improperly sealed tub
• Commonly replaced when you see visible seal wear, cracking, or recurring leaks

• One tall-lip outer tub seal (seal pack) as specified by the manufacturer

• Disconnect power and water supply before starting any repair
• Inspect mating surfaces and clean away residue before installing the new seal
• Some models may require partial disassembly of the cabinet or tub; follow the OEM service manual

This drain pump harness connects the washer's control/power circuits to the drain pump so the pump can run and remove water. Replacing a damaged harness restores reliable electrical connection for proper draining. What it does

• Provides power and signal paths between the control board and drain pump
• Enables the drain pump to run when the washer calls for pump operation
• Commonly associated with symptoms like no drain, intermittent pump operation, or pump not receiving power
• Prevents shorts or intermittent connections caused by frayed wires or damaged terminals

• Disconnect power before starting any repair to avoid shock or injury
• Inspect connectors for corrosion and ensure mating terminals are clean before connecting
• Route harness away from sharp edges, hot surfaces, and moving parts; secure with existing clips or fasteners

This is a 1/4-15 x 3/4 hex head screw used to secure components in laundry appliances. It provides a strong, threaded fastening point for panels and brackets so parts stay properly aligned during operation. What it does:

• Fastens panels, brackets, or components where a 1/4-15 x 3/4 hex head screw is specified
• Holds assemblies securely to reduce vibration and movement
• Can be used to replace a worn, stripped, or missing screw to restore proper fit
• Matches OEM thread and length for correct engagement when used as specified

• One 1/4-15 x 3/4 hex head screw

• Disconnect power to the appliance before performing any repairs
• Use the correct hex driver/socket to avoid rounding the head
• Tighten snugly but avoid over-torquing to prevent stripping threads or cracking components
• Replace with the exact part if damaged;

A replacement self-tapping pan-head screw sized 10 x 5/8 in for securing appliance panels, trim and small assemblies. Restores proper fastening where original screws are missing, stripped or corroded. What it does

• Cuts its own mating thread in sheet metal or plastic for secure fastening
• Commonly used to attach control panels, trim pieces and small brackets
• Helps stop rattles, loose panels and misaligned trim when original fasteners fail
• Corrosion-resistant finish resists rust in typical laundry appliance environments

• Use the correctly sized screwdriver or driver bit to avoid stripping the head
• Start in a pilot hole if material is brittle or if reinstalling into worn threads
• Do not over-torque; stop when the head seats flush to avoid cracking or stripping
• Disconnect power and follow appliance-specific safety procedures before working

This drive bell is the rotating cone that connects the washer's drive assembly to the transmission, transferring torque so the tub can agitate and spin properly. Replacing a worn bell restores reliable drive engagement. What it does:

• Couples the motor/drive shaft to the transmission to transfer rotational force
• Helps maintain proper drum rotation for agitating and spinning cycles
• Worn or damaged bell can cause loud knocking, grinding, or vibration during operation
• May lead to intermittent or failed agitation/spin if the drive engagement slips

• Disconnect power and water supply before servicing
• Follow the manufacturer service manual for disassembly and reassembly steps
• Inspect mating shaft, fasteners, and surrounding components; replace any damaged hardware
• Test the machine through a complete cycle after installation to ensure proper operation

This capacitive touch switch mounts behind the console and senses finger presses through the overlay, sending a signal to the control board. Replacing a failed switch restores consistent response from the affected touch button on touch-control machines.

• Detects user input at the touch area and communicates it to the main control
• Used for functions tied to specific keys (e.g., start, options, selections)
• Common failure signs: no response from a particular key, intermittent input, or needing excessive pressure
• Prevents a cycle from starting if the Start/Enter key's switch has failed

• Disconnect power to the appliance before servicing to avoid electrical shock
• Access the console/control area; note connector orientation and wire routing
• Install the new switch in the same position and orientation as the original
• Use ESD protection when handling electronics; reassemble and verify keypad operation

A tall service tub kit that replaces the washer's outer tub assembly to restore drum support and reduce leaks or abnormal vibration. Use this kit when the existing tub is cracked, dented, or no longer sealing properly. What it does:

• Replaces the washer's outer/service tub to restore proper drum alignment and containment
• Helps stop water leaks caused by cracked or damaged tubs
• Reduces excessive vibration or wobbling from a failing tub assembly
• Restores a secure mounting surface for seals, bearings and suspension components

• Disconnect power and water and follow all safety precautions before beginning service
• Installation may require removing the cabinet and drum; follow the OEM service manual for step-by-step instructions
• Use appropriate tools and a second person for lifting or aligning heavy components
• Inspect seals, bearings and suspension parts while the tub is exposed and replace as needed

This replacement inlet hose carries water from your household supply to the washer, restoring proper fill and preventing leaks. Use it when the washer fills slowly, won't fill, or shows water leakage at the connection. What it does:

• Channels hot and/or cold water from the household supply to the washer's inlet valve
• Restores normal fill behavior when an old or damaged hose causes slow or no fill
• Stops leaks caused by cracked, split or deteriorated hose sections or fittings
• Helps prevent water damage from a failed or leaking supply connection

• Turn off household water supply and unplug the washer before replacing the hose
• Hand-tighten fittings, then snug with a wrench—do not overtighten to avoid damaging threads
• Inspect and replace any damaged washers or seals at the connections

This 6-position cycle selector switch is the user control that lets the washer change between programmed wash cycles. Replaces a worn or faulty selector so you can choose the correct cycle and restore normal cycle selection. What it does:

• Routes control signals to the washer's timer/controls so the machine runs the selected cycle.
• Commonly replaces a switch that won't change cycles or doesn't register selections.
• Used when the knob feels loose, the selector clicks but cycle won't start, or cycle settings fail to change.
• Matches the original 6-position configuration for direct replacement.

• Disconnect power before servicing to avoid shock or injury.
• Remove the console or control panel to access the selector; note knob orientation for reassembly.
• Transfer or reconnect wiring exactly as found; label wires if needed.
• Test operation with power restored after reassembly; do not operate with panels loose.

This control assembly is the hybrid electronic control for 6-cycle top-load washers. It manages cycle selection and machine functions so your washer runs the selected wash programs reliably. What it does:

• Receives user inputs and starts, pauses, or advances wash cycles
• Controls timing and signals to motors, valves, and other subsystems
• Can cause no-start, unresponsive buttons, or stuck cycles if failing
• Helps resolve intermittent power-up, error codes, or cycle sequencing problems

• One control assembly (hybrid, 6-cycle)

• Disconnect power before removing or installing the control to avoid shock
• Handle the board and connectors carefully; avoid flexing the PCB or pulling on wiring
• Note connector positions and harness routing for reassembly; take photos if needed

This self-tapping screw secures panels and components on Speed Queen laundry appliances, restoring firm fastening and preventing rattles or gaps. Compact 8-18 x 3/8 size for use where a small, hex-washer-head fastener is required. What it does:

• Cuts its own mating thread in sheet metal or plastic mounting holes for a secure fit
• Holds control panels, trim pieces, and light brackets in place
• Replaces missing or damaged fasteners that cause loose or vibrating panels
• Helps restore proper panel alignment and reduces noise from loose parts

• Disconnect power before servicing the appliance
• Use the matching hex-washer driver or nut driver to seat the screw
• Start straight and apply steady pressure; avoid cross-threading
• Do not overtighten — snug until panels are secure

This lid lock wiring harness connects the washer lid lock assembly to the main wiring system, restoring the lid-lock signal for safe operation. It replaces a damaged or worn harness to help ensure the lid locks and unlocks reliably during cycles. What it does

• Provides the electrical connection between the lid lock switch and the washer control board
• Restores lost or intermittent lid-lock function caused by frayed or broken wiring
• Helps prevent the washer from starting or spinning when the lid is open (symptom: washer won't start or stops mid-cycle)
• Supports normal lock/unlock signaling during wash and spin cycles

• One lid lock wiring harness

• Disconnect power before starting — follow all electrical safety precautions
• Inspect connectors for corrosion or damage; replace harness only if matching connector type
• Route wiring clear of sharp edges and moving parts to avoid future wear

This replacement water inlet hose connects the home's water supply to the washer, restoring reliable water flow and preventing leaks at the rear hookup. Use when the original hose is cracked, split, or leaking. What it does:

• Carries incoming water from the fill valve to the tub for normal wash cycles
• Stops leaks caused by worn, cracked, or split inlet tubing
• Helps restore proper water fill when low or no-fill symptoms occur
• Matches OEM routing and connection points for a direct fit

• Disconnect power and shut off the water supply before beginning.
• Inspect and replace any worn clamps or fittings; tighten connections by hand then snug with a tool—do not overtighten.
• After installation, restore water and power, run a short fill cycle, and check all connections for leaks.