B36bt935ns Parts

Secures components inside the freezer compartment. Replace if broken, cracked, or missing to keep parts properly positioned during door operation.

This sensor monitors operating conditions inside the appliance and reports to the control so cycles run correctly and safely. When the sensor fails, the control may receive inaccurate feedback, leading to irregular performance. What it does:

• Detects key conditions inside the appliance and sends a signal to the control
• Helps the control regulate heat and cycle progress
• Failure symptoms can include erratic cycle times, poor heating performance, or sensor-related error messages
• Can prevent the appliance from starting or completing a cycle if readings are out of range

• 1 sensor

• Disconnect power before servicing; shut off water supply if applicable
• Access the sensor and note wire orientation before removal
• Ensure any sealing surface is clean and the sensor is seated properly; check for leaks after reassembly where applicable
• Run a diagnostic or test cycle after installation to clear errors and verify operation

Seals the freezer door to prevent cold air leaks and maintain temperature. Replace if torn, cracked, or no longer sealing properly. Confirm fit with model.

The Water Inlet Valve is an OEM replacement part for Bosch refrigerators. It is responsible for controlling the flow of water to the ice maker and dispenser. Over time, inlet valves can fail due to mineral deposits, solenoid failure, or plastic housing cracks. 

Symptoms of a defective inlet valve include: 

• No water dispensing 
• Slow dispensing
• Leaks
• Ice maker not making ice

The inlet valve is compatible with Bosch, Thermador, Gaggenau and some Kenmore refrigerator models.

This temperature limiter safeguards the evaporator defrost heater by opening the circuit if temperatures rise too high. Replacing a failed limiter restores defrost safety and helps prevent frost buildup and inconsistent cooling performance.

• Protects the defrost circuit by cutting power to the evaporator heater when an over-temperature condition is detected
• An open/failed limiter prevents the heater from energizing, causing frost accumulation on the evaporator and warm refrigerator temps
• Designed to be installed in the original location and orientation for accurate temperature sensing

• Disconnect power before servicing; evaporator fins and sheet metal are sharp—use cut-resistant gloves
• Access the evaporator compartment and note the limiter's original mounting and wire routing before removal
• Transfer any clips/insulation sleeves and reconnect wiring to the same terminals; do not bypass this safety device
• Reassemble, restore power, and monitor for normal defrost operation

Not getting ice from your refrigerator? This icemaker assembly produces and dispenses ice cubes automatically. Moderate DIY repair in 30-45 minutes.

Refrigerator not cooling or display blank? This electronic control board manages power distribution and operating logic to restore reliable function.

Manufacturer-specified service tool for bottom-mount refrigerators. Used to safely remove, adjust, or install components during repair or maintenance procedures.

Inline connector that joins internal water hoses in your refrigerator. Replace if leaking or connections are loose to restore sealed fit. Confirm compatibility.

Bypass plug allows refrigerator water dispenser operation without a filter. Install when water is pre-filtered or filtration isn't needed. Verify fit with your model number before ordering.

Replacement glass shelf panel for bottom-mount refrigerators. Installs as a shelf surface. Needed when original is cracked, shattered, or missing.

Fixes ice buildup on evaporator coils and poor cooling. This defrost heater melts frost during the defrost cycle to restore airflow and temperature control.

Secures the water filter in your refrigerator for a snug, leak-free fit. Replace if lost during filter changes, cracked, damaged, or worn out over time.

Replace worn door seal gaskets that cause cold air loss, frost buildup, or temperature issues. Restores tight closure. Verify fit with your model number.

This is a replacement micro switch used in select Bosch-built appliances. It opens and closes an electrical circuit when actuated by a lever or cam, enabling functions like starting/stopping a cycle or detecting a position.

• Controls power or signals by opening/closing a low-voltage circuit when pressed
• Commonly used for on/off, door/lid, or position-sensing functions
• Failure may cause the unit not to start, intermittent operation, or features that won't engage
• May also present as unresponsive buttons or functions that only work when pressed a certain way

• Disconnect power before servicing; verify no voltage is present
• Access location varies by model; remove panels as needed to reach the switch
• Note wire positions and terminal orientation before removal
• Test continuity with a meter after installation to ensure proper operation

Refrigerator not cooling properly or running constantly? The temperature sensor monitors internal temps and signals the control board. DIY-friendly repair.