Bosch She3ar72uc Parts

Replacement tube for Bosch appliances that routes water or drainage between components, helping restore correct flow, reduce pooling and leaks, and maintain normal appliance performance. What it does:

• Channels water between valves, pump and drain to enable normal water movement.
• Replaces cracked, split or blocked tubing that can cause leaks or standing water.
• Helps restore proper drainage and prevent water from pooling inside or under the appliance.

• Always disconnect power and shut off the water supply before servicing the appliance.
• Inspect and replace any damaged clamps, seals or fittings when installing the tube.
• Route the tube exactly as the original to avoid kinks; secure with the factory clamps or equivalent.

This temperature sensor (NTC) monitors wash temperature and reports it to the control so the cycle heats and advances correctly. Replacing a faulty sensor can restore proper cleaning performance and normal cycle times. What it does:

• Measures water temperature and sends resistance changes (NTC) to the control
• Helps the control regulate heating and cycle progression
• Failure symptoms can include no/insufficient heat, extended cycles, or poor drying
• May trigger a temperature-sensor fault (e.g., E11 on some models)

• 1 temperature sensor

• Disconnect power and turn off water supply before servicing
• Access is typically at the sump/heat-pump area; remove the toe-kick/lower panel as needed
• Expect some residual water; place a towel or tray to catch drips
• Ensure the sensor seats fully and the seal is in good condition to prevent leaks

This seal creates a tight, leak-proof interface between mating components inside your appliance. Replacing a worn seal helps stop drips and protects nearby parts for reliable, leak-free operation.

• Forms a watertight barrier between connected parts
• Replaces cracked, flattened, or deformed sealing material that can leak
• Helps address puddling, dampness, or seepage around the unit
• Maintains proper performance and helps prevent water damage to surrounding components

• Disconnect power and shut off the water supply before servicing
• Access the sealed joint and note the original orientation and seating depth
• Clean mating surfaces; do not use sealants unless specified by the manufacturer
• Seat the new seal evenly; lightly lubricate with a water-safe lubricant and run a test cycle to check for leaks

Tall item spray head.
This Spray Head is an OEM part for Bosch Dishwashers. It plays a role in distributing water evenly during the dishwasher's washing cycles. Continuous exposure to hard water, debris, or mineral deposits can cause issues with this component.

What Causes a Bad Spray Head:
Hard water deposits, debris, or mineral buildup can clog or block the spray head, affecting its performance. Physical damage can also impair its functionality.

Symptoms of a Bad Spray Head:

• Inadequate cleaning of dishes
• Uneven water distribution
• Reduced water pressure during washing cycles

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.
 

White tray handle that restores a secure grip and smooth operation to your appliance's tray. Direct-fit replacement that matches the original handle's mounting points for an easy, reliable swap-out. What it does:

• Provides a secure grip for pulling out and pushing in the appliance tray.
• Stabilizes the tray to help prevent tipping or accidental drops when loaded.
• Addresses symptoms like cracked, broken, loose, or missing handle that make the tray hard to open.
• Matches the original shape and mounting locations for proper fit and function.

• Disconnect power at the breaker or unplug the appliance before working near electrical components.
• Remove the tray or rack as needed to access mounting screws or clips; retain original hardware unless replacement hardware is specified.
• Align the handle with the mounting points and secure using the existing screws/clips; avoid over-tightening to prevent damage.

This replacement push button restores a crisp, reliable press at your appliance's controls so you can select settings as intended. It replaces a damaged or missing button that no longer operates the underlying switch.

• Provides the physical input you press to actuate the switch behind the control panel
• Symptoms can include a cracked, missing, sticky, or sunken button
• Restores proper travel and feel at the user interface

• Disconnect power to the appliance before servicing
• Access the control panel/fascia to reach the button per your model's procedure
• Release retaining clips/tabs or screws and install the new button in the same orientation
• Reassemble and test each control for proper operation

The Handle is an OEM part for Bosch dishwashers. It provides the surface for securely grasping and maneuvering the dishwasher door during opening and closing. 

Causes of a bad handle can include wear and tear from ongoing grasping motions. Repeated lifting and adjusting of the door places stress on handle components over time.

Symptoms of a bad handle include:

• Looseness, wobbling or detachment from the door assembly
• Sharp edges, cracks or splits compromising a firm grip
• Reduced ability to precisely guide the door into position

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This factory screw secures select Bosch/BSH appliance components. Use it to replace a missing or damaged fastener so panels, brackets, or trim stay tight and rattle-free during operation.

• Tightens and holds appliance parts such as panels, brackets, or trim in place
• Helps correct issues like loose or vibrating panels caused by a missing/stripped screw
• Maintains proper fitment after service or disassembly
• Torx T20 drive head helps resist cam-out during tightening

• Unplug power and shut off any water supply before servicing
• Use a T20 Torx driver; hand-start to avoid cross-threading
• Do not overtighten—snug to manufacturer torque guidance if available
• Replace any additional missing or damaged fasteners for even clamping

The Support is an OEM part for Bosch dishwashers. This part supports the door hinges, ensuring that the dishwasher door opens and closes smoothly and securely. The hinge support is vital for maintaining the alignment of the door, preventing stress on other components, and ensuring a proper seal during operation to avoid leaks.

Causes of hinge support failure often include mechanical wear and tear from frequent use, accidental damage from forceful handling, or corrosion from exposure to moisture and cleaning chemicals.

Symptoms of a failing dishwasher door hinge support include:

• Difficulty in opening or closing the dishwasher door
• A door that hangs unevenly or does not close fully
• Noticeable creaks or squeaks during door movement
• Increased effort required to operate the door

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Dishwasher Inner Door Panel is an OEM part for Bosch dishwashers. It is located inside the dishwasher door and protects internal components. 

Symptoms of a bad inner door panel include:

• Scratches, cracks, or damage impairing the appearance of the door interior
• Loose screws or mounting points causing rattling 
• Difficulty closing or sealing the door properly

Causes of a bad inner door panel can include prolonged exposure to heat and steam, damage from impact or mishandling of dishes, or normal wear over time compromising the integrity of the panel. 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Insulating Part is an OEM component specifically designed for Bosch dishwashers. This part plays an important insulating and sealing role, helping to keep heat and moisture contained within certain areas of the dishwasher. 

Causes of a bad insulating part can include damage or wear over time that compromises its insulating and sealing abilities. Cracks, tears, or compression of the insulating material are signs it needs replacement.

Symptoms of a bad insulating part include:

• Inefficient washing and drying performance due to loss of heat and moisture
• Higher energy costs as the dishwasher works harder to achieve the proper temperatures
• Dripping or pooling of water outside the intended areas  

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers. Replace yours today and restore your dishwasher's optimal insulation and seal.
 

This factory fastener secures panels, brackets, and internal components in your appliance. Replacing a missing or damaged screw restores a snug fit, reduces vibration and rattles, and keeps assemblies properly aligned during service or reassembly.

• Anchors panels, trim, and internal parts to the appliance frame or subassemblies
• Helps prevent vibration, buzzing, and loose or shifting components
• Ideal replacement for lost, stripped, or corroded hardware
• Common symptoms include loose panels, gaps, rattling noises, or parts that won't stay secured

• Disconnect power and shut off water or gas before servicing
• Match this screw to the original and replace one-for-one in the same location
• Start threads by hand to avoid cross-threading; use the correct driver and do not overtighten
• Inspect the mating clip/insert; replace if stripped or damaged for a secure hold

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

Replacement hood canopy that restores the vent cover and exterior appearance of your range hood. Installs in place of a dented, rusted, or damaged canopy to keep ventilation components protected and maintain a finished look. What it does:

• Covers and protects internal blower, controls and filters from grease, dust and damage
• Directs exhaust airflow through the hood; bent or crushed can disrupt ventilation
• Restores exterior appearance—visible dents, rust or corrosion are common signs it needs replacement
• Provides the proper mounting surface for filters and related hood components

• Disconnect power to the appliance before starting any repair
• Retain existing mounting hardware and seals unless new hardware is specifically listed as included

This hose clamp secures a rubber or plastic hose to its fitting inside the appliance, helping prevent leaks at connection points. Replace a stretched, corroded, or damaged clamp to maintain a tight, reliable seal.

• Clamps the hose to a barb or fitting to keep it from slipping off
• Helps maintain a watertight connection and reduce drips at the joint
• Can help resolve leaks caused by a loose hose connection
• Common signs: moisture around a hose joint, visible rust/deformation, or a clamp that won't tighten

• Disconnect power and turn off the water supply before servicing
• Place a towel or tray to catch residual water; note hose routing and clamp position
• Use appropriate hand tools for your clamp style; fully seat the hose and tighten evenly
• After reassembly, run a brief test and inspect for leaks at the connection

This replacement outer door panel forms the visible front of the appliance's door. It refreshes appearance and helps shield the inner door components when the original panel is dented, scratched, or warped. What it does:

• Forms the exterior door surface and protects the inner door and insulation
• Provides mounting points for the handle, badge, and trim
• Helps the door sit flush and latch properly when the old panel is bent or misaligned
• Common symptoms: dents, deep scratches, corrosion, loose/bent handle area, door not closing flush, rattling or vibrating panel

• 1 outer door panel

• Disconnect power before servicing; wear cut-resistant gloves—panel edges can be sharp
• Support the panel while removing perimeter screws from the inner door
• Transfer the handle, nameplate, and any insulation from the old panel to the new one
• Reinstall screws evenly without overtightening; verify latch alignment and door operation