Bosch She55m12uc Parts

The Push Button Set is an OEM part for Bosch dishwashers. It includes all buttons needed for cycle selection and temperature adjustments on the control panel.

Causes of a bad push button set can include wear from frequent use, moisture exposure compromising electronics, or physical damage from impact or other mishandling.

Symptoms of a bad push button set include:

• Buttons sticking, failing to depress properly, or malfunctioning entirely
• Inability to scroll through cycles or alter wash settings
• Control panel lights/display malfunctioning or unresponsive

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Float is an OEM part for Bosch dishwashers. This float senses water levels inside the dishwasher, signaling the inlet valve to refill when needed.

Causes of a float malfunctioning can be mineral deposits accumulating and weighing it down over time, or cracks in the plastic housing allowing water in.

Symptoms of a bad float include:

• The dishwasher not filling or filling slowly
• Error codes related to fill issues
• Improper water levels impacting wash results

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This control panel frame supports the user interface assembly and front fascia, keeping buttons and display properly aligned. Replacing a cracked or warped frame restores a secure console fit and consistent control response.

• Provides the structural housing and mounting points for the control/user interface assembly
• Maintains alignment of buttons, display, and touchpad overlay for reliable operation
• Secures the console and covers internal control components
• Typical signs of failure: loose or sagging control panel, broken tabs, gaps at the console, buttons sticking or misaligned

• Disconnect power before servicing; verify no voltage is present
• Support the console while removing screws/clips to protect wiring and connectors
• Transfer the user interface, control board, and hardware from the old frame to the new one one-for-one
• Ensure all tabs engage and do not overtighten screws to avoid cracking the frame

This actuator arm is the mechanical lever inside the dishwasher door's dispenser assembly. Working with its spring, it releases the detergent cup at the proper point in the cycle to restore consistent detergent dispensing. What it does

• Transfers motion from the control/drive mechanism to the dispenser latch to open the detergent cup
• Provides the spring tension needed for the lever to return to its home position
• Helps ensure detergent is dispensed at the intended time in the wash cycle
• Common symptoms include detergent left in the cup, a dispenser door that won't latch or opens inconsistently, or a visibly broken/missing lever

• 1 actuator arm with spring

• Disconnect power to the dishwasher before servicing
• Open the door and remove the inner door panel fasteners to access the dispenser linkage
• Note the spring orientation; move the spring to the new arm if needed and seat the arm in the correct pivot location
• Reassemble the door and manually test the dispenser action before running a cycle

Wax motor for detergent/rinse-aid dispenser.

Rear pump housing for the washer drain/pump assembly. Replaces the worn rear housing that supports the impeller and bearing, helping restore proper draining and reduce leaks or unusual pump noises when the housing fails. What it does:

• Houses and supports the pump impeller and bearing, forming the rear half of the drain pump assembly.
• Restores a sealed mounting surface to help prevent water leaks from the pump area.
• Helps re-establish correct water flow and draining when a cracked or worn housing impairs the pump.
• Addresses symptoms such as poor or no draining, water at the base of the appliance, or loud/grinding pump noises.

• Disconnect power and shut off water supply before starting; drain any standing water to avoid spills.
• Remove the washer access panels and pump assembly; transfer the impeller, seals, and any hardware as required.
• Inspect and replace pump gaskets/seals and the impeller if worn; tighten mounting fasteners to OEM torque where specified.

This replacement screw secures appliance panels and internal brackets so components stay tight and aligned during everyday use. Replacing missing or stripped hardware restores a solid fit and helps minimize vibration and rattling.

• Fastens covers, panels, and brackets to their mounting points
• Helps maintain alignment of the attached component
• Reduces movement that can cause noise or wear
• Typical reasons to replace: missing screw, stripped head/threads, loose panel or bracket

• Disconnect power and, if applicable, shut off water before servicing
• Use the driver bit specified for your model; hand start threads to avoid cross-threading
• Tighten snugly without over-torquing to prevent stripping
• Replace screws one at a time to maintain alignment

This factory screw secures appliance components per the original design, helping stop looseness and vibration. Replace a missing, stripped, or corroded fastener to restore a solid, rattle-free fit and protect nearby parts from damage.

• Secures panels, brackets, or internal components as specified by the manufacturer
• Helps maintain proper alignment and reduces vibration or rattling
• Replace if the head is stripped, threads are damaged, or the screw is missing
• Common signs include loose or misaligned panels/trim and hardware that won't stay tight

• Disconnect power and turn off water or gas supply as applicable before servicing
• Match length and thread to the original; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly without overtightening
• Retain any original washers, bushings, or clips used in the assembly

This control module is the electronic brain that manages power and cycle logic in your dishwasher. Replacing a failed module can restore start-up, cycle progression, and dependable operation when the control panel is unresponsive or the unit stops mid-cycle.

• Directs power to pumps, valves, and heaters and controls timing for each cycle
• Interfaces with the control panel and sensors to run the selected program
• Common failure symptoms: dead/unresponsive panel, won't start, stops mid-cycle or won't advance, intermittent operation, or electronic error codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Use ESD protection and handle the board by the edges only
• Photograph wiring and transfer connectors one at a time; secure the module in its housing
• Follow service instructions for any configuration/test mode after installation

Tall item spray head.
This Spray Head is an OEM part for Bosch Dishwashers. It plays a role in distributing water evenly during the dishwasher's washing cycles. Continuous exposure to hard water, debris, or mineral deposits can cause issues with this component.

What Causes a Bad Spray Head:
Hard water deposits, debris, or mineral buildup can clog or block the spray head, affecting its performance. Physical damage can also impair its functionality.

Symptoms of a Bad Spray Head:

• Inadequate cleaning of dishes
• Uneven water distribution
• Reduced water pressure during washing cycles

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.
 

This Filter Screen is an OEM part for Bosch Dishwashers. This filter screen efficiently traps debris and food particles, ensuring optimal washing performance.

A common issue with a faulty Filter Screen is clogging due to accumulated debris and food residue. Over time, this can obstruct water flow, resulting in poor cleaning performance or potential drainage problems.

Symptoms of a malfunctioning Filter Screen may include:

• Dirty dishes after a complete wash cycle
• Standing water at the bottom of the dishwasher
• An unpleasant odor emanating from the dishwasher

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This factory screw secures select Bosch/BSH appliance components. Use it to replace a missing or damaged fastener so panels, brackets, or trim stay tight and rattle-free during operation.

• Tightens and holds appliance parts such as panels, brackets, or trim in place
• Helps correct issues like loose or vibrating panels caused by a missing/stripped screw
• Maintains proper fitment after service or disassembly
• Torx T20 drive head helps resist cam-out during tightening

• Unplug power and shut off any water supply before servicing
• Use a T20 Torx driver; hand-start to avoid cross-threading
• Do not overtighten—snug to manufacturer torque guidance if available
• Replace any additional missing or damaged fasteners for even clamping

The Support is an OEM part for Bosch dishwashers. This part supports the door hinges, ensuring that the dishwasher door opens and closes smoothly and securely. The hinge support is vital for maintaining the alignment of the door, preventing stress on other components, and ensuring a proper seal during operation to avoid leaks.

Causes of hinge support failure often include mechanical wear and tear from frequent use, accidental damage from forceful handling, or corrosion from exposure to moisture and cleaning chemicals.

Symptoms of a failing dishwasher door hinge support include:

• Difficulty in opening or closing the dishwasher door
• A door that hangs unevenly or does not close fully
• Noticeable creaks or squeaks during door movement
• Increased effort required to operate the door

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This O-ring is a circular sealing gasket that creates a watertight joint between mating parts. Replacing a flattened or cracked ring restores a tight seal and helps prevent leaks during operation.

• Provides a compressible seal between fittings, hoses, or housings
• Helps prevent drips and leaks at joints under normal system pressure
• Maintains proper flow by keeping connections sealed
• Typical failure signs: visible cracking/flattening, seepage at a joint, pooling water near the appliance

• Disconnect power and shut off the water supply before servicing
• Relieve any line pressure and place a towel to catch residual water
• Clean and inspect mating surfaces; replace any damaged components
• Lightly lubricate the O-ring with approved silicone lubricant, seat evenly without twisting, and test for leaks after reassembly

This O-ring seals the NTC (negative temperature coefficient) temperature sensor where it inserts into the appliance. It restores a watertight seal at the sensor port to help prevent leaks and maintain reliable temperature-sensing performance.

• Provides a leak-tight seal between the NTC temperature sensor and its housing/tub/sump
• Helps prevent water seepage and moisture intrusion around the sensor opening
• Common symptoms of a failed seal: drips near the base, moisture in the leak tray, flattened/cracked ring, or a sensor that feels loose
• Good practice to replace when the NTC sensor is removed for service

• Disconnect power and shut off water supply before servicing
• Access the NTC sensor, remove the old O-ring, and clean mating surfaces
• Lightly moisten the new O-ring with water; seat it evenly to avoid pinching, then reinstall the sensor fully
• Run a brief test cycle and inspect for leaks

Small replacement O-ring that seals the dishwasher aqua sensor assembly to maintain a watertight seal and help ensure reliable sensor operation. Fits the sensor housing to reduce leaks and protect internal electronics. What it does:

• Seals the aqua/sensor housing to prevent water from escaping the sensor area
• Helps maintain accurate sensor readings by keeping the sensor dry and properly seated
• Commonly replaced when you see water pooling or dripping near the sensor assembly
• Used during aqua-sensor, pump, or housing repairs where the original seal is damaged

• Always disconnect power and turn off the water supply before starting repairs
• Replace the O-ring only when the sensor or housing is disassembled; inspect mating surfaces for damage or debris
• Ensure the O-ring is seated evenly in its groove before reassembly to avoid pinching or leaks