Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replace your washer drive belt if the drum won't spin or agitate. Connects motor to drum for proper washing cycles. Confirm fit with your model number.
Ordered new transmission, nut, split washer and spanner wrench to do the install. very straight forward fix after watching the video. spanner wrench is a must or the correct large socket with an impact driver. it was corroded on pretty well let the liquid wrench work for a while and then beat it off. approximately 2 hours to do to fix, spent some time cleaning stuff up also though. washer was 12 years old and debated scrapping it and getting a new one but then it would not match the dryer. ... Read more
Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.
The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job. Read more
Fix a washer that won't fill with hot water or overfills. This water inlet valve replacement takes about 45 minutes with basic tools and solves filling issues.
The new GE washers come with a fill valve that has a 1/8" hole for the hot water inlet. This is probably for energy savings or something. So, I installed the older style GE fill valve on my new machine. Since the older style has larger inlet holes for both hot and cold water, it fixed my problem easily. NOTE: The outlet nipple on the new style GE fill valves are larger than the older style. Therefore, I had to make a coupling piece to attach the older style GE valve outlet nipple to the... Read more
12-pack of inlet hose washers for washers and washer dryer combos. Replace cracked, worn, or missing washers to prevent leaks at water connections.
I called on your service, a person on the phone name Mr.Berry ask what the matter was . I told him the said a water valve should fix it . it sure was the right fix. thank you guys and thank you Mr. Berry. john m Read more
Seals the outer tub to prevent leaks during spin and drain cycles. Replace if washer leaks from the center or bottom. Confirm fit with your model number.
Outer basket had a lot of rust on the lip at the top of the basket, I ordered tub gasket, but when I removed the old gasket, some of the lip broke off, leaving gaps at the top, went to the hardware store, and purchased thin sheet of 8x10" aluminum, cut and shaped pieces from this sheet, to fit under the damaged lip, to bridge the gaps, rounded edges to fit against the rounded part of the outer tub, under the lip, once shaped, I glued them in place with emblem adhesive, did this all the way... Read more
Mounting screw for dryer drum support and internal components. Replaces lost, stripped, or damaged screws during repairs. Package of 12 screws included.
Watched the repair video. Saw what to look for. Found the dryer drum front support was broken and the slide bearings were worn. Replaced these items. Read more
Protective shield cover that installs inside your washer to guard internal components from heat and debris. Replace if cracked, broken, or missing.
Seals the washer tub to prevent water and oil leaks from the transmission area. Replace if you notice leaking during wash cycles. Verify fit with your model.
It is an old washing machine that is leaking oil from the transmission, and taking advantage of the disarmament want to change those parts that are damaged.the will rebuild replacing those parts and then paint it. Read more
Mounting screw for range installation and assembly. Replace missing, stripped, or damaged screws to secure panels, brackets, or components properly.
Cushions and supports the washer leg to reduce vibration and protect flooring. Replace if cracked, worn, or missing to stabilize and level your unit.
I ordered new foot pads and replaced the old ones. Now the washer runs better that it did when it was brand new. Read more
Supports washer drum for smooth, quiet rotation during spin cycles. Replace if you hear grinding noise or excessive vibration. Verify fit with your model.
Secures the door boot seal on your washer to prevent leaks. Replace if boot is loose, water leaks during cycles, or clamp is damaged. Verify fit.
Sound dampening pad that installs inside your washer to reduce vibration and noise. Replace if the original pad is cracked, torn, missing, or worn out.
Package of 12 screws with washers for securing washer panels, trim, and components. Replace missing, stripped, or damaged fasteners to restore fit.
Hose adapter for washer installation or stacking kits. Connects water supply lines to your machine. Replace if cracked, leaking, or missing threads.