Cdc22p2aww Parts

This door switch detects when the dishwasher door is fully closed and latched. Replacing a worn or intermittent switch restores reliable start/stop operation and ensures the safety interlock cuts power whenever the door is opened.

• Senses door-closed status and sends a signal to the control
• Interrupts power to the machine when the door opens
• Helps prevent operation with an unlatched door
• Typical failure symptoms: won't start, stops mid-cycle if the door is bumped, or only runs when pressing on the door

• Disconnect power at the breaker before servicing
• Access the latch/switch area by removing the inner door panel or console; note wire locations
• Transfer wires one at a time and secure the new switch in the bracket
• Verify latch engagement and switch actuation before restoring power

To order indicator lens use WP22001948.

This small retaining clip secures components in place inside the appliance, helping prevent movement, vibration, and premature wear. Replace a bent, fatigued, or missing clip to restore a solid, factory-tight hold.

• Holds panels, brackets, or tubing securely in their mounts
• Helps maintain alignment to reduce rattles, rubbing, or intermittent issues
• Common signs of failure: missing clip, loose fit, buzzing/vibration, parts that won't stay seated
• Restores proper retention after service, transport, or vibration-related fatigue

• Disconnect power and shut off gas/water before servicing
• Note the original clip's orientation; remove with needle-nose pliers
• Seat the new clip fully—do not over-bend; spring tension provides the hold
• Test operation before reassembly

This rack stop clips onto the end of a dishwasher rack rail to keep the rack from sliding off the track. Replacing a worn or missing stop helps the rack glide securely and prevents accidental pull-outs during use.

• Prevents the rack from being pulled out too far and falling off the rail
• Helps restore smooth, secure rack operation
• Common fix for racks that slide out too far or feel unstable

• Disconnect power and turn off water before servicing
• Pull the rack forward, depress the old stop's locking tab, and remove
• Align and snap the new stop onto the rail end until it locks
• Check rack travel to ensure the stop is fully engaged

This small rubber grommet seals the opening around the dishwasher's detergent/rinse-aid dispenser, helping prevent leaks and moisture intrusion so the dispenser operates reliably throughout the wash cycle.

• Seals the dispenser passage to keep water from leaking into or out of the dispenser cavity
• Helps ensure proper detergent or rinse-aid dispensing
• Can reduce moisture-related corrosion or staining in the dispenser area

• Disconnect power and turn off water before servicing
• Remove inner door panel to access the dispenser assembly
• Note grommet orientation; seat fully to ensure a watertight seal
• Inspect surrounding surfaces for debris or damage before reassembly

This O-ring seal fits into a groove to create a tight, leak-resistant barrier where two parts join. Replacing a worn O-ring helps stop drips at connections and keeps your appliance running reliably. What it does:

• Forms a compressible seal between mating parts (fittings, housings, or tubing)
• Helps prevent water or fluid leaks at joints
• Maintains proper pressure and flow within the sealed path
• Replace if you see seepage at the connection or the ring is cracked, flattened, brittle, or swollen

• 1 O-ring seal

• Disconnect power and shut off water supply before servicing
• Clean the groove and mating surfaces; remove debris that could compromise the seal
• Lightly lubricate with manufacturer-approved silicone grease; avoid petroleum-based products
• Seat the O-ring without twisting; reassemble carefully and check for leaks after testing

The Tub Wheel supports and guides the washer's tub assembly on its base during wash and spin cycles. Replacing a worn wheel restores smoother, quieter operation and helps reduce vibration and rubbing as the machine operates.

• Provides rolling support so the tub can move and self-balance during cycles
• Reduces friction between the tub and the base/frame
• Helps keep the tub centered to minimize noise and vibration
• Failure symptoms include squeaking or grinding, scraping noises, dragging movement, or visible flat spots/cracks on the wheel

• Disconnect power and water supply before servicing; wear appropriate gloves and eye protection
• Access the base/suspension per the service information and support the tub to remove load from the wheel
• Remove the retainer/axle, install the new wheel, and free rotation and correct orientation
• Reassemble, level the appliance, and run a spin test to check for noise and balance

Screw: 8-16 x 3/8 inch.

This replacement screw secures appliance panels, brackets, and components. Using the correct size restores a snug fit to reduce vibration, prevent loosening, and keep assemblies properly aligned during operation. What it does:

• Fastens sheet metal and component brackets in designated locations
• Replaces missing, stripped, or corroded hardware
• Helps eliminate rattling and vibration from loose panels
• Maintains proper alignment of covers and assemblies

• 1 screw

• Disconnect electrical power; shut off water or gas supplies if applicable
• Match length/thread to the original; replace one fastener at a time to preserve alignment
• Start by hand to avoid cross-threading; use the correct driver size
• Snug firmly but do not overtighten to prevent stripping

Specs: No.8X1/2 HEX WASHER HEAD

This twin-wheel caster replaces a worn or broken wheel on compatible portable appliances and carts, restoring smooth rolling and easier repositioning. A fresh caster helps improve stability and reduces dragging that can scuff floors.

• Supports the unit's weight and lets it roll for cleaning or repositioning
• Twin-wheel design helps distribute load and track smoothly
• Common signs of failure: cracked or missing wheel, caster won't swivel, flat spots, unit hard to move or sits unevenly
• Replacing damaged casters reduces wobble and noise when rolling

• Disconnect power and shut off water. Empty the unit as needed before moving.
• Carefully tip or elevate and support the appliance to access the caster; use a helper to avoid injury.
• Remove the retaining fastener/clip, transfer any spacers, and install the new caster in the same orientation.
• After installation, verify all casters are seated, the unit rolls smoothly, and it sits level.

This tub wheel mounts on the dishwasher's tub wall to guide and support the rack as it slides in and out. Replacing a worn wheel restores smooth rack movement and helps prevent binding, noise, and derailments.

• Mounts to the tub to provide rolling support for the dish rack/rail
• Replaces cracked, flattened, or missing wheels that impede rack travel
• Helps fix racks that stick, bind, are hard to pull/push, or derail
• Reduces grinding or squeaking from the rack area

• Disconnect power at the breaker before servicing
• Open the door and pull the rack forward for access
• Release the old wheel from its retainer/axle per your model's design; install the new wheel in the same orientation
• Ensure the wheel spins freely and the rack slides smoothly before use

Small replacement screw that secures panels and internal components on compatible appliances. Restores proper fastening to reduce rattling and loose parts so controls and panels stay aligned during normal use. What it does:

• Secures panels, brackets, and small components to the appliance frame or assemblies.
• Helps stop rattling, vibration-related noise, and movement from loose parts.
• Replaces a missing, worn, or stripped fastener to restore proper mounting.
• Used wherever the original manufacturer specified this screw in service diagrams.

• Disconnect power and water before working on the appliance to avoid shock or injury.
• Match the replacement screw to the original by fit and thread before installation; do not force mismatched fasteners.
• Start the screw by hand to avoid cross-threading; tighten securely but avoid over-torquing which can strip threads or damage components.
• Refer to the appliance's service manual or parts diagram for exact location and any torque or threadlocker recommendations.

This upper spray arm sprays water across the top rack to help remove food and rinse dishes for better cleaning coverage. It replaces a damaged or clogged upper spray arm to restore normal spray pattern. What it does

• Directs pressurized water to clean dishes on the upper rack
• Helps reduce missed spots and improve rinse performance
• Replaces worn, cracked, or clogged upper spray arms
• Works with the dishwasher's existing spray system and fittings

• Disconnect power to the dishwasher (unplug or turn off circuit breaker) before servicing
• Turn off the water supply to the appliance if required by your model
• Remove the upper rack to access the spray arm; handle gently and avoid forcing fittings
• Run a short test cycle after installation to ensure proper fit and spray coverage

A replacement tension spring designed to restore proper movement and return force to the appliance mechanism. Helps the affected component operate smoothly so doors, levers or assemblies move with correct tension and alignment. What it does:

• Provides return and holding tension for the appliance mechanism to restore normal movement.
• Helps reduce sagging, misalignment, or loose operation of the associated door or linkage.
• Minimizes noise and vibration caused by a worn or weakened spring.
• Works as the direct-fit part when the listed part number matches your appliance.

• Disconnect power and water (if applicable) before beginning any repair.
• Springs are often under tension—wear eye protection and use caution when removing or installing.
• Follow the appliance's service manual or OEM instructions for correct orientation and safe installation.

This jump-up nozzle directs water flow inside the dishwasher to improve rinse and spray coverage. It replaces a worn, cracked, or clogged nozzle to restore proper water routing for consistent wash performance. What it does:

• Directs water upward from the spray arm/dispenser area for targeted rinsing
• Helps maintain even spray distribution across dishes
• May cause poor rinsing, spotting, or uneven cleaning when damaged or clogged
• Compatible with dishwasher models that use a jump-up style water nozzle

• One jump-up nozzle

• Designed for drop-in or snap-fit replacement; inspect surrounding seals and clips
• Turn power off and shut off water supply before beginning repair
• Use basic hand tools; avoid overtightening plastic fittings
• Replace only with the exact nozzle specified for your model