Cfe3050lsk Parts

This quick-connect clip secures 5/16-inch water tubing in push-to-connect fittings to prevent accidental release and leaks at the joint. Restore a reliable hold on dispenser and icemaker lines when the original clip is missing or damaged. What it does:

• Locks the release ring (collet) on a 5/16-inch quick-connect fitting to retain tubing
• Helps prevent water drips or leaks at the connector
• Keeps tubing from slipping out, supporting steady water flow to dispenser/ice maker
• Common symptoms: leak at fitting, loose/disconnected tubing, no/low water or ice

• 1 quick-connect clip (5/16)

• Unplug the appliance and shut off the water supply; dispense water to relieve line pressure
• Ensure the tubing end is cut square; push it fully into the fitting until seated
• Insert the clip beneath the fitting's collet to lock; tug gently to verify retention
• Restore water and power, then check all connections for leaks

• Designed for 5/16-inch OD water tubing quick-connect fittings

Replacement grille thermistor. This temperature sensor monitors air at the grille location and relays the signal to the control so cooling and defrost responses stay consistent and food stays within target temperatures.

• Senses ambient air temperature at the grille and varies resistance with temperature
• Sends data to the control to help regulate compressor/fan run time and defrost intervals
• Aids in maintaining stable refrigerator and freezer temperatures
• A failing sensor may lead to temperature swings, extended run time, or irregular defrosting

• Disconnect power before servicing
• Remove the grille/kickplate to access the sensor and its connector
• Disconnect the old sensor, install the new one, and route wiring as originally; ensure the sensor is fully seated and wires aren't pinched
• Restore power and allow up to 24 hours for temperatures to stabilize

Port Gasket forms a watertight seal around the refrigerator dispenser port to prevent leaks and moisture intrusion. Installing a fresh gasket restores proper sealing and helps stop dispenser drips and water pooling. What it does:

• Seals the dispenser/port opening to prevent water from leaking at the door area.
• Helps stop visible dripping or pooling near the dispenser and reduces moisture buildup.
• Replaces worn, cracked, flattened, or missing gaskets that allow leaks or drafts.
• Restores a proper seal so the dispenser operates without water escaping around the port.

• Disconnect power (and shut off the water supply if working near the dispenser) before beginning work.
• Remove the old gasket and thoroughly clean mating surfaces to ensure a full seal.
• Press the new gasket evenly into the port opening, making sure it seats all the way around.
• After installation, restore power/water and run a small dispense test to confirm no leaks.

Conduction heater for the freezer compartment that melts frost from the evaporator during defrost cycles, helping prevent ice buildup and maintain consistent cooling. Replaces a failed freezer conduction heater to restore defrost function. What it does:

• Heats the evaporator area during defrost cycles to melt accumulated frost and ice.
• Helps prevent excessive ice buildup that can reduce cooling efficiency.
• Common symptoms of a failing heater: visible ice/frost on the evaporator or freezer interior and inconsistent freezer temperatures.
• Designed as a replacement conduction heater for compatible GE freezer evaporator assemblies.

• Disconnect power to the appliance before servicing to avoid electric shock.
• Access typically requires removing the freezer evaporator cover or rear panel.
• Handle the element carefully to avoid damage.

The Slide Basket Lower Fz is an OEM part for GE freezers. This slide is responsible for smoothly gliding the freezer basket or drawer in and out, allowing for easy access and organization of frozen food items. It ensures that the freezer basket or drawer operates smoothly, making it effortless to retrieve items and maximize storage space.

A bad lower basket or drawer slide can occur due to wear and tear, damage, or other internal malfunctions. If you notice symptoms such as difficulty in sliding the freezer basket or drawer, sticking or jamming, or the basket or drawer not staying securely in place, it may be time to replace the slide.

Symptoms of a bad slide include:

• Difficulty in sliding the freezer basket or drawer
• Sticking or jamming of the basket or drawer
• Basket or drawer not staying securely in place

Restore organization to your GE freezer by replacing the faulty drawer slide with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

Right handed Hinge

This lint screen lid hinge connects the dryer's lint lid to its mounting point, allowing smooth, aligned opening and secure closing. Replacing a bent or broken hinge restores proper lid operation and helps keep lint contained in the trap.

• Provides the pivot point for the lint screen lid/cover
• Helps the lid sit flush and stay aligned when closed
• Symptoms of a failed hinge can include a loose or misaligned lid, difficulty opening/closing, or squeaking/binding at the hinge
• Replace when the hinge is bent, cracked, or missing

• Disconnect power before servicing; sharp cabinet edges—wear cut-resistant gloves
• Support the lint lid to avoid bending or scratching
• Remove the mounting screws, note the hinge orientation, and transfer the new hinge in the same position
• After reassembly, cycle the lid open/closed to ensure smooth operation before restoring power

Specs: 8-18 AB IHW 5/8 S

This retainer clip secures a component in place to prevent movement and maintain proper alignment during appliance operation. Replacing a damaged or missing clip helps restore safe, reliable performance.

• Holds the mating part firmly to reduce vibration and noise
• Helps prevent intermittent operation caused by loose fitment
• Common fix when a component feels loose, rattles, or won't stay seated

• Disconnect power and shut off gas/water before servicing
• Note original clip orientation and location before removal
• Use needle-nose pliers to carefully release and install the clip
• Do not over-bend the clip; replace if deformed or fatigued

Restore reliable heat to your dryer. This replacement heating element generates the hot air needed to dry laundry efficiently, helping cycles reach proper temperature and finish on time when the original element has failed.

• Converts electrical energy into heat to warm air passing through the drum
• Failure modes include open coil or short-to-housing
• Common symptoms: no heat, weak heat, longer dry times, visible breaks or hotspots on the coil, tripped breaker or thermal cutoff
• Useful diagnostic step: check the element for continuity and for shorts to ground

• Disconnect power before service; elements get extremely hot and retain sharp edges
• Handle the coil carefully and avoid bending or touching the bare element; support terminals/insulators during transfer
• Move any reusable brackets, insulators, or wiring from the original as required
• After installation, check related thermostats/thermal cutoffs if heat issues persist

Restore your appliance's factory look with this badge assembly. It replaces a missing, cracked, or faded logo on the refrigerator exterior, delivering a clean, professional appearance without affecting performance or operation.

• Decorative nameplate/logo for the refrigerator exterior
• Replaces cracked, faded, loose, or missing badge
• Restores a clean, factory appearance
• Cosmetic component; does not impact cooling or function

• Disconnect power before servicing the appliance
• Protect the finish; use a plastic trim tool to remove the old emblem if needed
• Clean and dry the mounting area; align with locating marks/holes and secure per your model diagram

Kit of 24 clips

Replacement drum baffle that lifts and tumbles clothes inside the dryer for more even drying and helps prevent garments from snagging. Restores proper drum agitation to reduce noise and improve drying performance. What it does:

• Lifts and separates clothes as the drum turns to promote even heat exposure and drying.
• Helps keep items from bunching or wrapping around the drum, which can cause uneven drying.
• Reduces rattling, thumping, or scraping noises tied to a loose or damaged lifter.
• Protects fabrics from snagging or rubbing against the drum surface.

• Disconnect power to the appliance before beginning service to avoid shock or injury.
• Access may require removing the dryer front panel or drum.
• Keep fasteners and mounting tabs aligned during reassembly to ensure the baffle seats correctly.

This SCR is a solid-state switching module that controls on/off power flow in select appliance circuits. Replacing a failed SCR helps stop intermittent operation and restores reliable switching for affected motors or heating elements. What it does:

• Regulates electrical switching in the control circuit to turn motors or heaters on and off.
• Used where a solid-state switch is required for smooth, repeatable control.
• Symptoms of a failing SCR: appliance won't start, runs intermittently, hums without operating, or a controlled circuit does not respond.
• Restores proper switching when the original SCR is shorted, open, or erratic.

• Disconnect power to the appliance before beginning service; follow lockout/tagout procedures.
• Handle as an electronic component—avoid static discharge and protect the spade terminals from bending or contamination.
• Ensure correct orientation and secure mounting; reconnect wiring exactly as shown on the appliance wiring diagram.

A replacement crossbar pinion that engages the ice-maker ejector crossbar to advance the harvest cycle. Installs on the ice maker drive assembly to restore proper rotation of the ejector and help clear ice from the mold. What it does:

• Drives the ice-maker crossbar/ejector during the harvest cycle so ice cubes are pushed out.
• Transfers rotation from the ice-maker motor/cam to the ejector crossbar.
• Common symptoms: ice maker won't advance or eject cubes, loud grinding or clicking from the ice bin, or visible broken/missing gear teeth.
• Restoring a worn or broken pinion can stop jamming and allow normal harvest cycles to resume.

• Disconnect power to the appliance before servicing; shut off the water if removing the ice maker assembly.
• Remove the ice maker per the manufacturer's instructions to access the pinion; handle plastic gears carefully to avoid damage.
• Inspect mating gears and the ejector crossbar for wear or damage and replace any damaged components to prevent repeat failure.
• After installation, restore power and run a test harvest cycle to ensure proper operation.

The Switch Paddle Assembly is an OEM component specifically designed for GE side-by-side refrigerators. This assembly consists of the control switch and controls access for various refrigerator features and functions. 

Causes of a bad switch paddle assembly can include repeated use over time, unintended impacts, liquid spills inside the fridge, or damage to internal wiring/electronics. 

Symptoms of a bad switch paddle assembly include: 

• Faulty or unresponsive control switches  
• Lights or compartments not functioning properly
• The control panel displaying error codes
• Internal refrigerator components running unexpectedly

Replace this assembly to restore full functionality to your refrigerator’s control center. This genuine GE OEM part ensures dependable access to cooling, dispensing, and other common settings. It is compatible with Hotpoint, RCA, and some Kenmore models as well.